Filtern
Erscheinungsjahr
Dokumenttyp
Sprache
- Englisch (15) (entfernen)
Referierte Publikation
- ja (15) (entfernen)
Schlagworte
- High pressure airborne ultrasound (2)
- Kohlenstoffschichten (2)
- Thermo-acoustic (2)
- 4H–SiC (1)
- Accelerated testing (1)
- Air-coupled ultrasonic transducers (1)
- Alkali silica reaction (1)
- Amorphous (1)
- Amorphous state (1)
- Ar gas cluster gun (1)
Organisationseinheit der BAM
- 6 Materialchemie (4)
- 6.1 Oberflächen- und Dünnschichtanalyse (2)
- 6.7 Materialsynthese und Design (2)
- 4 Material und Umwelt (1)
- 4.1 Biologische Materialschädigung und Referenzorganismen (1)
- 6.6 Physik und chemische Analytik der Polymere (1)
- 7 Bauwerkssicherheit (1)
- 7.1 Baustoffe (1)
- 7.4 Baustofftechnologie (1)
The irradiation of ~0.9-µm-thick hydrogenated amorphous carbon (a-C:H) layers deposited on silicon substrates with single femtosecond (fs) laser pulses (35 fs pulse duration, 790 nm centre wavelength) in air is studied experimentally. Irradiation spots have been generated with different peak fluences and subsequently investigated by optical topometry, micro Raman spectroscopy and microscale mechanical indentation in order to evaluate their microscopic, topographical, structural and mechanical properties (e.g. elastic modulus). By this multi-method approach, a clear separation of different effects (delamination and graphitisation) becomes possible. The joint application of mechanical and spectroscopic techniques provides unique insights into the effects of the fs-laser radiation on the carbon layer.
Fluid-assisted mass transport reactions by dissolution-precipitation, where a precursor mineral reacts with a fluid, play an important role in metamorphism and metasomatism. We investigated titanite growth on rutile in time series experiments between one and 107 days at constant P-T conditions of 600 °C and 400 MPa in the system TiO2-CaO-SiO2-Na2O-HCl-H2O. A two-capsule assemblage allows for transport of Ca and Si from dissolving wollastonite to dissolving rutile, the Ti-source, in a NaCl-bearing aqueous fluid, according to the general reaction CaSiO3 + TiO2 = CaTiSiO5. Complete overgrowth of rutile by titanite occurred after just one day of experiment. Fine-grained lozenge-shaped titanite crystals of short-time runs (up to 14 days) reorganize to larger predominantly prismatic crystals after >14 days.
After investigation by scanning electron microscopy, the titanite overgrowth was removed from the rutile by hydrofluoric acid, to provide a three-dimensional view of the dissolution-reaction front on the rutile surface. The morphology of the rutile surface is dominated by humps or ridges beneath the central region of a titanite crystal and valleys at the grain boundaries between adjacent titanite crystals. The dissolution pattern on the rutile surface mimics the titanite overgrowth and changes with changing grain size and shape of the titanite with longer run times. The preferred dissolution of rutile in the valleys is clearly linked to the position of the titanite grain boundaries, which served as pathways for fluid-assisted element transport. Rutile-titanite and titanite-titanite boundaries show a significant porosity in transmission electron microscopy images of foils prepared by focused ion beam milling. The large-scale dissolution pattern on the rutile surface is independent of the crystallographic orientation of the rutile and entirely dominated by the arrangement of titanite crystals in the overgrowth. Dissolution features on a scale smaller than ~1 µm are dominated by stepwise dissolution and etch-pits following the crystallographic orientation of the rutile. Similar observations were made in experiments with an additional Al-source, although these experiments result in a different overgrowth pattern; i.e., an exposed rutile surface is always present and solitary titanite crystals are accompanied by partial overgrowths. Quantitative characterization of the surface morphology by white-light interference microscopy demonstrates that, with increasing grain size of titanite, dissolution of rutile is strongly enhanced at the titanite grain boundaries.
Natural examples of titanite overgrowths on rutile show the same relations between element pathways, arrangement of titanite crystals and 3D dissolution pattern on rutile as in the experimental systems. We conclude that the transport of Ti away from the rutile and of Ca + Si into the reaction rim occurred in a grain boundary fluid, the composition of which must have been strongly different from the composition of the bulk fluid in the experiment, as well as in the natural system. The reaction progress depends on the availability of a fluid, and relicts of rutile in titanite indicate restricted availability of fluid in the natural system (e.g., a fluid pulse that was consumed by the reactions). The reaction examined here can serve as a proxy for other reactions of the conversion of oxide minerals (e.g., spinel or corundum) into silicates.
In this contribution we present a novel thermo-acoustic approach for the generation of broad band airborne ultrasound and investigate the applicability of resonance-free thermo-acoustic emitters for very short high pressure airborne ultrasound pulses. We report on measurements of thermo-acoustic emitter consisting of a 30 nm thin metallic film on a usual soda-lime glass substrate, generating sound pressure values of more than 140 dB at 60 mm distance from the transducer and compare the results with conventional piezoelectric airborne ultrasound transducers. Our experimental investigations show that such thermo-acoustic devices can be used as broad band emitters using pulse excitation.
Hydrogen-Containing Amorphous Carbon Layers as Optical Materials in the Near-IR Spectral Range
(2007)
Hydrogenated amorphous carbon layers were deposited on various substrates by means of a plasma CVD process with a RF substrate bias as well as an ECR plasma source. The optical properties of the a-C:H layers were obtained via spectroscopic ellipsometry and correlated with their mechanical and chemical properties. The layers from pure RF plasma exhibit a higher absorption constant in the visible spectral range and a higher refractive index. All layers are nearly transparent in the NIR spectral range making them candidates for optical thin layer systems. The laser damage behaviour of the a-C:H layers was investigated with ultrashort pulses. The damage thresholds were consistent with the absorption constants of the layers. Interesting damage morphologies were observed indicating a sensitivity of this experiment to sub-structures in the layer.
Most of the polymeric materials used are easy to ignite and show extensive flame spread along their surfaces. Apart from extensive heat release rates, their short time to ignition (tig), in particular, is a key fire hazard. Preventing ignition eliminates fire hazards completely. Protection layers that shift tig by more than an order of magnitude are powerful flame retardancy approaches presenting an alternative to the usual flame retardancy concepts.
Coatings are proposed that consist of a three-layer system to ensure adhesion to the substrate, acting as an infrared (IR) mirror and protecting against oxidation. The IR-mirror layer stack is realised by physical vapour deposition in the sub-micrometre (<1 µm) range, reducing heat absorption by up to an order of magnitude. Not only is the ease of ignition diminished (tig is increased by several minutes), the flame spread and fire growth indices are also remarkably reduced to as little as 1/10 of the values of the uncoated polymers open for further optimization. Sub-micrometre thin IR-mirror coatings yielding surface absorptivity <0.1 are proposed as a novel and innovative flame retardancy approach.
The extremely low acoustic impedance of polypropylene ferroelectret combined with its piezoelectric properties makes this material suitable for construction of aircoupled ultrasonic transducers for non-destructive testing. For the fabrication of transducers with a stable quality, the reproducibility of their key parameters is of interest.
The reproducibility was evaluated by means of (i) impedance spectroscopy and (ii) pulse-echo measurements. (i) Impedance spectroscopy was applied to identify the resonance frequency, the coupling factor and the acoustic impedance of several nominally identical transducers. (ii) Pulse-echo measurements yielded the signal form of these transducers.
The variation of the signal amplitude measured with pulseecho technique was about 10 dB. A part of this variation Comes from the deposition of transducer electrodes and another part from local variations of ferroelectret properties. The variation of the signal amplitude was caused by the observed variation of the coupling factor, which was also about 10 dB. The variation of the acoustic impedance was only about 1 dB, thus having no effect on the variation of the signal amplitude.
These results indicate that the variability can be reduced by improving the control of electrode deposition and by optimizing the production technology affecting the reproducibility of material properties.
A novel approach for the generation of broadband airborne ultrasound by using the thermo-acoustic effect is presented in this contribution. We investigate the applicability of resonance-free thermo-acoustic emitters for generation of very short high pressure airborne ultrasound pulses. A thermoacoustic emitter consisting of a 30 nm thin metallic film on a usual soda-lime glass substrate generates sound pressure values of more than 140 dB at 60 mm distance. The results are compared with conventional piezoelectric airborne ultrasound transducers. Our investigations show the applicability of the thermo-acoustic devices for broadband and high pressure ultrasound emitters using pulse excitation.
Alkali-silica reaction (ASR) is a chemical reaction within concrete which can lead over time to cracking and spalling. Due to the complexity of the problem, it still causes damage to concrete constructions worldwide.
The publication aims to illustrate the interdisciplinary research of the German Federal Institute for Materials Research and Testing (BAM) within the last 20 years, considering all aspects of ASR topics from the macro to the micro level. First, methods for characterization and assessment of ASR risks and reaction products used at BAM are explained and classified in the international context. Subsequently the added value of the research approach by combining different, preferably nondestructive, methods across all scales is explained using specific examples from a variety of research projects. Aspects covered range from the development of new test-setups to assess aggregate reactivity, to analysis of microstructure and reaction products using microscopical, spectroscopical and X-ray methods, to the development of a testing methodology for existing concrete pavements including in-depth analysis of the visual damage indicator and the de-icing salt input using innovative testing techniques. Finally, research regarding a novel avoidance strategy that makes use of internal hydrophobization of the concrete mix is presented.
Deep understanding of the effects associated with fabrication parameters and their influence on the resulting structures shape is essential for the further development of direct laser writing (DLW). In particular, it is critical for development of reference materials, where structure parameters are precisely fabricated and should be reproduced with use of DLW technology. In this study we investigated the effect of various fabrication and preparation parameters on the structural precision of interest for reference materials. A well-studied photo-curable system, SZ2080 negative photo-resist with 1 wt.% Michler's ketone (Bis) photo-initiator, was investigated in this work. The correlation between applied laser power, laser velocity, fabrication direction on the deviations in the structure shape were observed by means of white light interferometry microscopy. Moreover, influence of slicing and hatching distances as well as prebake time were studied as function of sample shape. Deviations in the structure form between the theoretically expected and the one detected after DLW fabrication were observed in the range up to 15%. The observed shape discrepancies show the essential importance of fine-tuning the fabrication parameter for reference structure production.
The growing interest in artificial bioorganic Interfaces as a platform for applications in emerging Areas as personalized medicine, clinical diagnostics, biosensing, biofilms, prevention of biofouling, and other fields of bioengineering is the origin of a need for in Detail multitechnique characterizations of such layers and interfaces. The in-depth analysis of biointerfaces is of special interest as the properties of functional bioorganic coatings can be dramatically affected by in-depth variations of composition.
In worst cases, the functionality of a device produced using such coatings can be substantially reduced or even fully lost.