Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (56)
- Buchkapitel (1)
Sprache
- Englisch (57)
Referierte Publikation
- ja (57) (entfernen)
Schlagworte
- Nanocomposites (6)
- Broadband dielectric spectroscopy (5)
- Graphene (5)
- Rubber (5)
- Biodiesel (4)
- Dilation (4)
- Environmental stress cracking (ESC) (4)
- Molecular mobility (4)
- Nanocomposite (4)
- Polymers of intrinsic microporosity (4)
Organisationseinheit der BAM
- 7 Bauwerkssicherheit (28)
- 7.5 Technische Eigenschaften von Polymerwerkstoffen (28)
- 6 Materialchemie (15)
- 6.6 Physik und chemische Analytik der Polymere (14)
- 5 Werkstofftechnik (10)
- 5.3 Polymere Verbundwerkstoffe (10)
- 6.5 Synthese und Streuverfahren nanostrukturierter Materialien (4)
- 8 Zerstörungsfreie Prüfung (2)
- 8.5 Röntgenbildgebung (2)
- 4 Material und Umwelt (1)
A report is presented on the development of a test for determining the long-term oxidation resistance of polyolefin materials, which is accelerated not only by elevated temperatures but also by increased oxygen pressure and a stirred aqueous medium. The method permits durability tests to be carried out at markedly lower temperatures with reasonable testing durations and significantly reduced diffusion limited oxidation effects and allows for physical and chemical impacts of aqueous media. Oxidative durability can be assessed by autoclave immersion exposures at three different temperatures (60, 70 and 80 degrees C) and 50 bar oxygen pressure and at 80 degrees C and two different oxygen pressures (usually 10 and 20 bar). Accelerated test data are evaluated by modified Arrhenius equations with the application of a three-dimensional regression analysis. The application of the test method to various materials, including PP non-woven materials and geosynthetics is demonstrated. 10 refs.
Dielectric Study of Molecular Mobility in Poly(propylene-graft-maleic anhydride)/Clay Nanocomposites
(2005)
Polymer/clay nanocomposite materials based on poly(propylene-graft-maleic anhydride) (PPgMAH) and two different organophilic modified clays were investigated by dielectric relaxation spectroscopy (DRS). In contrast to ungrafted polypropylene (PP), PPgMAH shows a dielectrically active relaxation process which can be assigned to localized fluctuations of the polar maleic anhydride groups. Its relaxation rate exhibits an unusual temperature dependence, which could be attributed to a redistribution of water molecules in the polymeric matrix. This is confirmed by a combination of Raman spectroscopy and thermogravimetric experiments (TGA) with real-time dielectric measurements under controlled atmospheres. In the nanocomposites this relaxation process is shifted to higher frequencies up to 3 orders of magnitude compared to the unfilled polymer. This indicates a significantly enhanced molecular mobility in the interfacial regions. In the nanocomposite materials a separate high-temperature process due to Maxwell-Wagner-Sillars (MWS) polarization was observed. The time constant of this MWS process can be correlated with characteristic length scales in nanocomposites and therefore provides additional information on dispersion and delamination/exfoliation of clay platelets in these materials. These properties also influence the diffusivity of the water molecules as revealed by real-time dielectric investigations.
Pyrolysis, flammability, fire behavior, melt viscosity, and gas diffusion of bisphenol A polycarbonate/acrylonitrile-butadiene-styrene (PC/ABS) were investigated, with bisphenol A bis(diphenyl phosphate) (BDP), with 10 wt.% talc and with BDP in combination with 5, 10 and 20 wt.% talc, respectively. Compared to PC/ABS, PC/ABS + BDP results in an increased decomposition temperature of PC, a higher char yield, a significantly increased LOI, a V-0 classification in UL 94, a reduced peak heat release rate (pHRR), and a reduced total heat release (THR) in the cone calorimeter. This efficient flame retardancy is due to mechanisms in both the gas and condensed phases. PC/ABS + 10 wt.% talc shows a decrease in the PC decomposition temperature. The fire behavior is improved in part compared to PC/ABS, with an increased LOI and reduced pHRR. PC/ABS + BDP + 10 wt.% talc shows a strong synergism in LOI, a V-0 classification, and a decrease in pHRR, whereas THR is slightly increased compared to PC/ABS + BDP. Talc decreases the gas diffusion and enhances the flow limit for low shear rates, both of which influence the pyrolysis and flammability results. Further, talc improves the protection properties of the fire residues. Nevertheless it also partly suppresses flame inhibition and the charring effect of BDP. The synergism between BDP and talc in LOI is obtained even for low talc loadings in PC/ABS + BDP + talc, whereas for higher loadings saturation is observed.
Effect of well dispersed amorphous silicon dioxide in flame retarded styrene butadiene rubber
(2013)
Spherically shaped amorphous silicon dioxide with broad size particle distribution was used in combination with aluminium trihydroxide (ATH) in styrene butadiene rubber composites. The pyrolysis, flammability, fire properties, flame spread and gas diffusion were investigated. The kind and amount of ATH, but in particular the fine silicon dioxide chosen as an additive, influenced the thermal decomposition and fire behaviour of styrene butadiene rubber composites. Gravimetric gas sorption measurements showed that the gas diffusion was systematically lower with silicon dioxide. The initial pyrolysis gas release was hindered, increasing the temperature at which decomposition begins as well as the ignition time in fire tests. During combustion, ATH and silicon dioxide accumulate on the surface of the specimen, forming a residual protective layer. A reduced peak heat release rate and fire spread were observed. The addition of a special kind of silicon dioxide is proposed to play a key role in optimising fire retardancy.
Detailed atomistic simulations were carried out for swelling polymer/gas systems related to experimental sorption and dilation data for CO2 and CH4 in three glassy polymers (polysulfone PSU, the polyimide 6FDA-TrMPD, and a polymer of intrinsic microporosity PIM-1) at 308 K (35 °C) and pressures up to 50 bar. Corresponding experiments were performed with a gravimetric sorption balance and a dilatometer based on a capacitance distance sensor. For each polymer/gas system molecular packing models were prepared and equilibrated for two reference states: the pure polymer is taken as reference for the respective 'unswollen' state and similarly the state of the highest penetrant pressure reached in the corresponding experiment is taken to represent the 'swollen' state. Models for the latter were constructed in agreement with experimental data (pressure, temperature, gas concentration and volume dilation). Concentration–pressure isotherms of each polymer/gas system were obtained using Grand Canonical Monte Carlo (GCMC) simulations for both reference states (depleted of gas molecules), which are in good agreement with the experimental data in the respective pressure range. As expected these isotherms – due to the simulation technique used, merely based on hole-filling in a static host matrix – do not represent the sorption behavior over a broader range of gas pressures which may involve significant structural rearrangements as well as swelling and relaxational phenomena. Nevertheless, a linear combination of the two GCMC-isotherms allows the interpolation in order to describe the nonlinear gas sorption in the glassy polymers under investigation covering the penetrant pressure range between the reference states in good agreement with the experimental results.
Nanocomposites were prepared by solution blending of polyhedral oligomeric silsesquioxane with phenethyl substituents (PhenethylPOSS) into polystyrene (PS). The prepared materials were investigated by dielectric spectroscopy, differential scanning calorimetry (DSC), and density measurements. Additional FTIR investigations were carried out. Pure polystyrene shows two relaxation processes, an intermediate β*-process at lower and the α-relaxation at higher temperatures, the latter corresponding to segmental dynamics (dynamic glass transition). The molecular assignment of the β*-process needs further investigation. PhenethylPOSS can be incorporated into PS up to about 40 wt % without any indication of phase separation. With increasing PhenethylPOSS content, the α-relaxation of the composites shifts to lower temperatures and the loss peak broadens. Thus, the main effect of the nanofiller in the polystyrene matrix is to enhance the segmental dynamics, i.e., plasticization. The incorporation of approximately 40 wt % (approximately 5 mol %) PhenethylPOSS shifts the glass transition temperature Tg by 50 K to lower temperatures. The obtained results for polystyrene are discussed together with those reported recently for polycarbonate where a phase-separated morphology is observed for higher concentrations of PhenethylPOSS. The different behavior of PhenethylPOSS in polystyrene and polycarbonate is interpreted in terms of the different interaction of the phenyl rings within the POSS substituents with the phenyl rings of the polymers. For polystyrene, the interaction is stronger than for polycarbonate which probably leads to the enhanced miscibility of PhenethylPOSS into polystyrene. A detailed analysis of the temperature dependence of the dielectric relaxation strengths points also to additional interactions in the nanocomposites when compared to pure polystyrene. The broadening of the loss peak with increasing concentration is discussed in the framework of composition fluctuations.