Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (35)
- Beitrag zu einem Sammelband (16)
- Beitrag zu einem Tagungsband (16)
- Vortrag (6)
- Buchkapitel (1)
Sprache
- Englisch (38)
- Deutsch (35)
- Mehrsprachig (1)
Schlagworte
- Wear (12)
- Friction (10)
- Fretting (9)
- Reibung (8)
- Tribologie (6)
- Verschleiß (6)
- Temperature (5)
- Keramik (4)
- Wires (4)
- Contact pressure (3)
Eingeladener Vortrag
- nein (6)
The influence of temperature and counterbody material on the tribological properties of a-C:H coatings deposited on Cronidur 30 steel has been investigated in a lubricated ball on disk contact situation. The results show, that the wear volumes of the system increase exponentially with increasing temperature. Two different wear mechanisms seem to have a major influence: First, the abrasive action due to materials hardness and second, the tribooxidation when silicon nitride is counter material.
The influence of temperature and counterbody material on the tribological properties of a-C:H
coatings deposited on Cronidur 30 steel has been investigated in a lubricated ball on disk
contact situation with alpha-alumina and silicon nitride as counterbodies. The results show, that the wear volumes of the systems increase exponentially with increasing temperature, for alpha-alumina more than for silicon nitride. Two different wear mechanisms seem to have a
major influence: First, the abrasive action due to materials hardness and second, the tribo-oxidation when silicon nitride is counter material.
After having checked in a previous study the influence of stroke and normal load in laboratory fretting tests accomplished with thin steel roping wires, in this paper the effect of the contact pressure (test configuration), environmental conditions (relative humidity) and reduction of the friction coefficient (lubricants) on the wear behaviour were analysed. The wires were 0.45 mm in diameter and the material was a cold-drawn eutectoid carbon steel (0.8% C) with a Tensile Strength over 2800 MPa. The tests were performed on an oscillating test rig and the volumetric wear of both specimens of the tribocouple was determined separately from three-dimensional topographies of the wear scars acquired by means of a confocal profiler, and a calculation algorithm developed in using MATLAB®. The strong effect of humidity and lubrication on wear behaviour was proved, whereas a slight effect of contact pressure was derived.
A new method for sampling wear particles directly from the lubricant reservoir has been developed and applied successfully for analyzing wear particles by high-resolution scanning electron microscopy in transmission mode having coupled energy-dispersive X-ray spectroscopy. The lubricated tribological testing was carried out with fully formulated as well as with non-formulated synthetic base oil. It was possible to analyze individual particles with dimensions as small as about 5–30 nm which are likely the 'primary' wear particles. A majority of the particles, however, are agglomerated and, thus, lead to the formation of larger agglomerates of up to a few micrometers. Chemical analysis led to the conclusion that most of the observed particles generated in formulated oil, especially the larger ones, are composed of the additives of the lubricant oil. In non-formulated base oil, the primary particles are of similar dimensions but contain only iron, chromium and oxygen, but most likely stem from the mating materials. This finding points to the fact that the main wear mechanism under lubricated conditions with fully formulated oil is more like a continuous shearing process rather than a catastrophic failure with the generation of larger primary particles. When the oil is non-formulated, however, several wear mechanisms act simultaneously and the wear rate is increased significantly. Generated larger primary particles are milled down to the nanoscale. When the oil is fully formulated, wear mainly takes places at the additive layer or tribofilm; thus, the steel surface is protected.
Main focus was on the correlation of the coefficient of friction (COF) with the geometrical parameters of the surface during early stage of the running-in period. TiN, TiAlN and AlTiN coatings were prepared by using rotating cathode arc evaporation unit. The roughness of the WC-Co substrate Ra ranged from 0.05 to 0.2 µm and the coating thickness was 2.3 ± 0.2 µm. Part of the samples were subjected to the surface modification by the drag grinding finishing. Geometrical parameters of the surface were evaluated by means of atomic force microscopy (AFM) and fretting tests were conducted with 10 mm diameter alumina ball under 2 N load, 100 µm slip distance and the frequency of 10 Hz. It was found that the distribution of macroparticles strongly influences the geometrical parameters of the surface and the number of macroparticles increases with increasing Al content in the coating. In the case of the positive skewness Ssq of the coating surface, the kurtosis Sku provides a statistically significant effect on the COF, namely the COF depends inversely on the kurtosis Sku. The kurtosis value for TiN was the highest among as-deposited coatings, subsequently, the slowest increase rate in the COF was observed for the TiN coating.
Diamantähnliche Kohlenstoffschichten (DLC) zeichnen sich durch ein sehr günstiges Reibungs- und Verschleißverhalten aus. Auf vielen Werkzeugen und hochbelasteten Bauteilen ist DLC daher bereits erfolgreich im Einsatz. In naher Zukunft wird die Bedeutung dieser Schichten als Oberflächenschutz in tribologischen Systemen weiter ansteigen.
Wie viele Applikationsbeispiele zeigen, ist die Leistungsfähigkeit von DLC als Schicht zur Verringerung von Reibung und Verschleiß zwar groß, weist aber auch Grenzen auf. Vor allem bei höheren Temperaturen (> 300 °C) treten Strukturveränderungen oder sogar Oxidationsvorgänge auf, die auch die tribologischen Eigenschaften der Schichten verschlechtern können.
Reibungs- und Verschleißuntersuchungen (Schwingungsverschleiß) von DLC-Schichten wurden im Temperaturbereich von 25 °C bis 250 °C durchgeführt und zeigen ein schnelleres Durchreiben der Schicht bei höheren Temperaturen. Die Lebensdauer der Schichten wird mit zunehmender Prüftemperatur reduziert. Einsatzgrenzen für DLC-Schichten können abgeleitet werden.