Filtern
Erscheinungsjahr
Dokumenttyp
Schlagworte
- Fatty acids (2)
- High-spin molecule (2)
- Multiple spin transition (2)
- Multistability (2)
- Rhenium (2)
- 119mSn- and 57Fe-Mössbauer spectroscopy (1)
- 3D Scanning (1)
- ATR-FTIR spectroscopy (1)
- Albumin (1)
- Biochip (1)
Organisationseinheit der BAM
The precursor [FeIII(L)Cl] (LH2 = N,N'-bis(2'-hydroxy-3'-X-benzyliden)-1,6-diamino-3-N-hexane) is a high-spin (S = 5/2) complex (with X = -CH3, -O-CH3). This precursor is combined with the bridging unit [SnIV(CN)4] to yield star-shaped pentanuclear clusters, [(L-X-FeIII)4Sn(CN)4]Cl4 57Fe-Mössbauer, 119mSn-Mössbauer, and ESR spectroscopy are used to study our samples. For X = -CH3 the 57Fe-Mössbauer data show a multiple spin transition between iron(III) in the high-spin and low-spin state. Changing the functional group from X = -CH3 to X = -O-CH3 turns the switchability off.
Laser tissue soldering (LTS) based on indocyanine green (ICG)-mediated heat- denaturation of proteins might be a promising alternative technique for micro-suturing, but up to now the Problem of too weak shear strength of the solder welds in comparison to sutures is not solved. Earlier reports gave promising results showing that solder supported by carrier materials can enhance the cohesive strength of the liquid solder. In these studies, the solder was applied to the carriers by dip coating. Higher reliability of the connection between the solder and the carrier material is expected when the solder is bound covalently to the carrier material. In the present study a poly(ether imide) (PEI) membrane served as carrier material and ICG- supplemented albumin as solder substrate. The latter was covalently coupled to the carrier membrane under physiological conditions to prevent structural protein changes. As laser source a diode continuous-wave laser emitting at 808 nm with intensities between 250mW and 1500mW was utilized. The Albumin functionalized carrier membrane was placed onto the tunica media of explanted pig thoracic aortae forming an overlapping area of approximately 0.5×0.5 cm2. All tests were performed in a dry state to prevent laser light absorption by water. Infrared spectroscopy, spectro-photometrical determination of the secondary and Primary amine groups after acid orange II staining, contact angle measurements, and atomic force microscopy proved the successful functionalization of the PEI membrane with albumin. A laser power of 450mW LTS could generate a membrane-blood vessel connection which was characterized by a shear strength of 0.08±0.002MPa, corresponding to 15% of the tensile strength of the native blood vessel. Theoretically, an overlapping zone of 4.1mmaround the entire circumference of the blood vessel could have provided shear strength of the PEI membrane-blood vessel compound identical to the tensile strength of the native blood vessel. These in-vitro results confirmed the beneficial effects of solder reinforcement by carrier membranes, and suggest LTS with covalently bound solders on PEI substrates for further studies in animal models.
We report polyethylene glycol (PEG)-grafting antifouling surfaces using a plasma copolymerized (PcP) technique to monitor protease activity in complex media. By varying the mixing ratio of the PEG and ethylenediamine (EDA) precursors, the PcP-PEG-EDA (PcP-PE) film was able to easily control surface amine density with good preservation of the internal PEG structure. We found that nonspecific protein adsorption was dramatically reduced in serum-containing media on the PcP-PE films, as opposed to that on plasma polymerized-EDA (PP-E) films without PEG. When SPR sensor chips coated with PcP-PE film were employed to detect protease activity, biotinylated luciferase probes (luciferase-peptide-biotin) on streptavidin-conjugated SPR chips enabled real-time and label-free measurement of matrix metalloproteinase activity in cell culture media. Owing to its excellent antifouling ability, this newly developed method boasts minimal nonspecific binding and can serve as a biochip platform to promote a wide range of applications in the biological field.
The precursor [FeIII(L)Cl] (LH<sub2 = N,N'-bis(2'-hydroxy-benzyliden)-1,6-diamino-3-N-hexane is a high-spin (S = 5/2) complex. This precursor is combined with the bridging units [SnIV(X)4] (X = CN-, NCS-) to yield star-shaped pentanuclear clusters, [(LFeIII-X)4Sn]Cl4. For X = CN- the 57Fe-Mössbauer data show a multiple spin transition between iron(III) in the high-spin and low-spin state, while the 119mSn-Mössbauer data indicate a valence tautomerism between Sn(IV) and Sn(II). Changing the bridging unit from X = CN- to X = NCS- turns the switchability off.
Hemocompatible materials are needed for internal and extracorporeal biomedical applications, which should be realizable by reducing protein and thrombocyte adhesion to such materials. Polyethers have been demonstrated to be highly efficient in this respect on smooth surfaces. Here, we investigate the grafting of oligo- and polyglycerols to rough poly(ether imide) membranes as a polymer relevant to biomedical applications and show the reduction of protein and thrombocyte adhesion as well as thrombocyte activation. It could be demonstrated that, by performing surface grafting with oligo- and polyglycerols of relatively high polydispersity (>1.5) and several reactive groups for surface anchoring, full surface shielding can be reached, which leads to reduced protein adsorption of albumin and fibrinogen. In addition, adherent thrombocytes were not activated. This could be clearly shown by immunostaining adherent proteins and analyzing the thrombocyte covered area. The presented work provides an important strategy for the development of application relevant hemocompatible 3D structured materials.