Filtern
Erscheinungsjahr
Dokumenttyp
- Vortrag (134)
- Zeitschriftenartikel (66)
- Beitrag zu einem Tagungsband (66)
- Beitrag zu einem Sammelband (32)
- Forschungsbericht (14)
- Posterpräsentation (13)
- Buchkapitel (1)
Sprache
- Englisch (170)
- Deutsch (149)
- Spanisch (5)
- Französisch (2)
Schlagworte
- Ground vibration (39)
- Layered soil (13)
- Slab track (11)
- Mitigation (10)
- Railway track (10)
- Bahnerschütterungen (9)
- Erschütterungen (9)
- Finite-element boundary-element method (9)
- Track-soil interaction (9)
- Train passage (9)
Organisationseinheit der BAM
- 7 Bauwerkssicherheit (82)
- 7.2 Ingenieurbau (82)
Eingeladener Vortrag
- nein (134)
Long wooden floor beams above a ball room in an old historical palace have been analysed experimentally. The eleven beams are weakly coupled by three layers of floor boards. It has been investigated if the state (the stiffness) of the wooden beams can be determined by vibration measurements of global or preferably local modes. Hammer, heel-drop and ambient excitations have been used. The vibration modes of the structure show dominating local deformations if an impact excitation is applied. This is understood as the positive superposition of several modes which yield the maximum at the excitation point but a cancellation at more distant points. Natural modes have been estimated from these vibration modes by standard and special methods which were necessary for the high damping of the wooden floor. It has been found that all floor beams contribute to each natural mode even for a weak coupling of the beams. In addition to the modal discussion, the impact tests have also been analysed for the wave propagation and amplitude attenuation with distance. The coupling of floor beams has been studied theoretically by an analytic multiple-beam model where the coupling by translational or rotational springs and by a common support motion has been assumed.
Messungen bei Fern- und Hochgeschwindigkeitsbahnen aus verschiedenen Ländern (Portugal, Spanien, Belgien, Großbritannien, Deutschland, Schweiz, China, Japan u.a.) sollen die besondere Wichtigkeit eines mittelfrequenten Erschütterungsanteils zeigen. Relativ einheitlich werden dabei drei zusammenhängende Terzen mit angehobenen Amplituden beobachtet. Dieser Erschütterungsanteil dominiert mit zunehmender Entfernung vom Gleis das Frequenzspektrum der Erschütterungen. Die hochfrequenteren Anteile nehmen aufgrund der Materialdämpfung des Bodens stärker ab, die tieffrequenteren Anteile aus der sogenannten Quasistatik, der Vorbeifahrt der statischen Achslasten, verschwinden innerhalb der ersten zehn Meter vom Gleis fast vollständig. Die Frequenzcharakteristik des mittelfrequenten Erschütterungsanteils wird durch die Achsfolge des Zuges bestimmt. Im Terzmaßstab ist die Achsfolge im Drehgestell maßgeblich für die Ausprägung von zwei Amplitudenminima, die den Frequenzbereich eingrenzen. Diese Achsfolgespektren sind auch bei Brückenschwingungen von Bedeutung. Sie können die schwächere oder stärkere Anregung einzelner Brückeneigenschwingungen regeln. Die Ursachen der Boden- oder Brückenschwingungen sind mit den Achsfolgespektren noch nicht geklärt. Bei der Brücke und beim Boden können kurzwelligere Gleislagefehler (auch Radunrundheiten 1. Ordnung) Fahrzeugbeschleunigungen und damit dynamische Kräfte auf das Gleis erzeugen. Bei der Brücke ist die diskontinuierliche Auf- und Abfahrt der Achsen ebenfalls eine relevante Anregung, während die Kraftimpulse auf das Gleis, die durch die Achsüberfahrten entstehen, für die Wellenausbreitung im Boden von Bedeutung sind. Heterogene Böden oder Gleise ergeben einen Zerstreuanteil der Achsüberfahrtimpulse. Fallbeispiele mit verschiedenen Böden und verschiedenen Fahrgeschwindigkeiten werden ausgewertet, um die Ursachen und Gesetzmäßigkeiten des mittelfrequenten Erschütterungsanteils zu erkennen.
Die Bedeutung von Eisenbahn-Achsüberfahrten für die Bodenerschütterungen und Brückenschwingungen
(2016)
Messungen bei Fern- und Hochgeschwindigkeitsbahnen aus verschiedenen Ländern (Portugal, Spanien, Belgien, Großbritannien, Deutschland, Schweiz, China, Japan u.a.) sollen die besondere Wichtigkeit eines mittelfrequenten Erschütterungsanteils zeigen. Relativ einheitlich werden dabei drei zusammenhängende Terzen mit angehobenen Amplituden beobachtet. Dieser Erschütterungsanteil dominiert mit zunehmender Entfernung vom Gleis das Frequenzspektrum der Erschütterungen. Die hochfrequenteren Anteile nehmen aufgrund der Materialdämpfung des Bodens stärker ab, die tieffrequenteren Anteile aus der sogenannten Quasistatik, der Vorbeifahrt der statischen Achslasten, verschwinden innerhalb der ersten zehn Meter vom Gleis fast vollständig. Die Frequenzcharakteristik des mittelfrequenten Erschütterungsanteils wird durch die Achsfolge des Zuges bestimmt. Im Terzmaßstab ist die Achsfolge im Drehgestell maßgeblich für die Ausprägung von zwei Amplitudenminima, die den Frequenzbereich eingrenzen. Diese Achsfolgespektren sind auch bei Brückenschwingungen von Bedeutung. Sie können die schwächere oder stärkere Anregung einzelner Brückeneigenschwingungen regeln. Die Ursachen der Boden- oder Brückenschwingungen sind mit den Achsfolgespektren noch nicht geklärt. Bei der Brücke und beim Boden können kurzwelligere Gleislagefehler (auch Radunrundheiten 1. Ordnung) Fahrzeugbeschleunigungen und damit dynamische Kräfte auf das Gleis erzeugen. Bei der Brücke ist die diskontinuierliche Auf- und Abfahrt der Achsen ebenfalls eine relevante Anregung, während die Kraftimpulse auf das Gleis, die durch die Achsüberfahrten entstehen, für die Wellenausbreitung im Boden von Bedeutung sind. Heterogene Böden oder Gleise ergeben einen Zerstreuanteil der Achsüberfahrtimpulse. Fallbeispiele mit verschiedenen Böden und verschiedenen Fahrgeschwindigkeiten werden ausgewertet, um die Ursachen und Gesetzmäßigkeiten des mittelfrequenten Erschütterungsanteils zu erkennen.
The damage detection and repair control have become important tasks for ballast and slab tracks. Measurements which compare the damaged and the repaired status of the same track section at different times, or which compare a damaged and an intact track section at the same time, have been successfully performed at some sites in Germany with slab tracks and ballast tracks and compared with the theoretical behaviour of intact and damaged tracks. The loss of contact between the sleeper and the plate, between the plate and the base layer, and some problems with soft or weakened soil have been analysed. The observed results, changes in the time histories of displacements and velocities due to train passages and in the transfer functions (compliances) due to hammer impacts, are encouraging that these measurements can be used to detect track damage. In addition, calculations with the combined finite-element boundary-element method have been used to confirm the conclusions about intact or damaged railway tracks.
The vibrations of soil and foundations are demonstrated for different types of loading. Train-induced ground vibrations are studied in a measurement campaign where a test train has run with regularly varied speeds. The measured train-induced soil vibration at 2 to 100 m distance from the track is compared with the wave propagation due to hammer excitation and with the theoretical wave field. The strong influence of the soil and the train speed on the amplitudes and frequencies of the vibration has been analysed for passages of the locomotive and the carriages. - The generation of ground vibration by strong explosions has been studied on a large testing area with sandy soil. The propagating waves were measured in a regular grid of measuring points in 10 to 1000 m. Therefore, the dominance of certain waves at certain distances and the changes of compressional waves and Rayleigh waves could clearly be observed. The results are compared with impulse hammer measurements in the range of 5 to 50 m. - A drop test facility has been built on the testing area of the Federal Institute of Materials Research and Testing (BAM). Heavy masses (containers) of up to 200 t can be dropped from 10 m height on a big reinforced concrete foundation. The foundation was instrumented by accelerometers, strain gauges and pressure cells to give information about the loading condition and by geophones to measure the vibration of the surrounding soil and building. Both excitation processes, the release of the mass and the impact, produce high vibration amplitudes. On a smaller drop foundation, the influence of the drop height and the target stiffness has been studied more systematically.
Der Erhalt und die Weiterentwicklung der Verkehrsinfrastrukturen werden auch zukünftig einen Investitions- und Forschungsschwerpunkt in Deutschland bilden. Gemäß den aktuellen Entwicklungsprognosen sowohl der Bundesregierung als auch der Deutschen Bahn wäre bei unveränderten Marktanteilen der Bahn eine Zunahme insbesondere des Güterverkehrs in den kommenden 10 Jahren um ca. 50% zu erwarten. Dieser Zuwachs erfordert erhebliche Entwicklungen sowohl in der technischen Konstruktion der Fahrwege als auch im Erschütterungs- und Lärmschutz infolge des Schienenverkehrs.
A survey of the phenomena and methods for floor vibrations is presented. Experimental results of floor vibrations are shown for many floors in six different buildings. The signals have been evaluated for waves and modes by simple procedures. General rules have been established between the material and the area of a specific floor, and its local eigenfrequency. The damping values of the floor vibrations have been found between D = 1 and 10 % where somewhat higher values have been measured for wooden floors, and a weak correlation with the eigenfrequency has been established. The velocities of bending waves propagating in a storey and the attenuation with distance in the building have been analysed. A considerable transfer of vibration from one room to far away parts of the building has been found in the studied buildings with concrete and wooden floors. An example building has been analysed for modes of coupled floor bays. The strong coupling of similar neighbouring floor bays would yield a wide band of global resonance frequencies. The measured wooden floor exhibits a weak coupling of the neighbouring floor bays and a narrower band of eigenfrequencies. A special method has been tested with the impulse measurements to estimate the coupled eigenmodes in presence of the high damping. From the ambient measurement, a low-frequency vibration mode has been detected which includes the vibration of the whole building and the soil. The coupling of floors to other floors and the whole building is an important phenomenon of structural dynamics which should be observed for the prediction of vibration due to internal and external sources.
Train-induced ground vibration can be excited by wheel and track irregularities and by two kinds of irregularities of the soil, by geometric irregularities or by the spatially varying soil stiffness. For both types of irregularities, the effective track irregularity on top of the track is calculated in wavenumber domain and with wavenumber integrals. For a general multi-beam track model, the wavenumber integrals are solved numerically. The irregularities of the soil are filtered by the track when transferred from the bottom to the top of the track. The high-wavenumber irregularities are strongly reduced due to the bending stiffness of the track and the compliance of the support. In addition, soft track elements reduce directly the stiffness variation of the support. Therefore, the mitigation effect of elastic track elements for these excitation components seems to be important. For under-sleeper pads and slab tracks, calculation and measurements are presented including additional excitation components and the dynamic vehicle–track interaction, and the relevance of the excitation mechanisms is discussed based on the dynamic forces which are acting on the ground. Due to the restricted amplitudes, the parametric excitation by the stiffness variation seems to be less important than the geometric irregularities. The calculations yield the correct trends of the measurements and many details of the measured ballast, slab, and under-sleeper-pad tracks.
Train-induced ground vibrations are generated by static and dynamic axle loads which can be calculated by vehicle-track-soil models and the vehicle and track irregularities. A fast prediction method has been developed which uses approximate transfer functions of layered soils. In the present contribution, this prediction method is used for the inverse calculation of the axle-load spectra from the measured ground vibration. The layered soils of some measuring sites show very differing ground vibration spectra in the amplitude range of 0.0001–1.0 mm/s as a consequence of the soft layer and stiff half-space, differing layer frequencies, as well as the far- and near-field measuring points. The back-calculation, however, yields axle-load spectra within a single order of magnitude around 1 kN. Axle-box measurements confirm the amplitude level of the axle loads. This standard axle-load spectrum can be used for a basic prediction at a new site. The separation of train and site-specific components allows a better evaluation of railway vibrations, for example, of different trains and different tracks. By eliminating the effects of differing soil characteristics, an important mid-frequency component has been found which lies between 8 and 32 Hz depending on the train speed. The origin of this dominant mid-frequency component is discussed using advanced prediction methods like moving constant loads, scattered axle impulses and axle-sequence spectra.
Deckenschwingungen stellen in der Regel das größte Problem bei Erschütterungsgutachten dar. In diesem Übersichtsbeitrag werden folgende Aspekte der Deckenschwingungen mit einfachen bis komplexen Rechenmodellen dargestellt.
Die Resonanzanregung der Decken hängt von der Phasenlage der Auflagerschwingungen ab. Der Wellenlauf der anregenden Freifeldbodenschwingungen kann die Resonanzstärke deutlich verringern. - Der Wellenlauf kann bei Pfahl- oder Plattengründungen zu Abminderungen der Freifeldamplituden führen (kinematische Bauwerk-Boden-Wechselwirkung). - Die Steifigkeit des Untergrundes hat einen starken Einfluss auf die Resonanzstärke. Dies hat einerseits mit der Abstrahlungsdämpfung zu tun, andererseits auch mit einer Schwingungstilgung. Die Tilgung kann in einem vereinfachten Wand-Decken-Modell mit einer einheitlichen Deckeneigenfrequenz oder realistischer mit einem Eigenfrequenzband berechnet werden. In einem schmalen Frequenzband vor der Deckeneigenfrequenz können weitere (Wand-) Eigenfrequenzen und nach der Deckeneigenfrequenz eine Frequenzlücke auftreten. Normalerweise nehmen die Deckenamplituden mit der Höhe im Gebäude zu. In der Frequenzlücke hingegen nehmen die Amplituden mit der Höhe ab. - Benachbarte Deckenfelder können gemeinsame Deckeneigenfrequenzen besitzen, vor allem wenn sie die gleichen Abmessungen haben. Man bekommt dann ein Band von Deckeneigenfrequenzen. - Bei einer Schwingungsanregung im Gebäude auf einer Decke schwingen auch die benachbarten Deckenfelder mit. Im Frequenzbereich lassen sich Übertragungsfunktionen darstellen, im Zeitbereich können Amplituden-Abstandsgesetze betrachtet werden. - Bei großen Stützenbauwerken treten häufig Kopplungen der Decken verschiedener Stockwerke auf. - Mit den verschiedenen Methoden lassen sich typische Gesetzmäßigkeiten für die Amplituden und Frequenzen der Deckenschwingungen ableiten.
The reduction of train-induced ground vibration by elastic elements such as rail pads and sleeper pads has been analyzed by a combined finite-element boundary-element method. The dynamic compliance of the track, the transfer function of the total force on the ground and the ground vibration ratios have been calculated for a variety of isolated and un-isolated track systems. It has been found that the soil force transfer, which describes the excitation force of the soil, is an appropriate quantity to predict the reduction of the ground vibration and the effectiveness of isolated tracks. All force transfer functions of isolated tracks display a vehicletrack resonance where the wheelset on the compliant track is excited by wheel and track irregularities. At higher frequencies, considerable reductions of the amplitudes are observed as the benefit of the resilient element. The influence of the stiffness of the rail or sleeper pads, the ballast and the soil, and the mass of the sleeper and the wheelset on the resonance frequency and the reduction has been investigated. Sleeper pads are advantageous due to the higher mass that is elastically supported compared to the rail-pad track system. The combination of elastic rail and sleeper pads has been found to be disadvantageous, as the second resonance occurs in the frequency range of intended reduction.
The computation of the wave propagation in homogeneous and layered soils can be performed by a numerical integration in wavenumber domain. The numerical difficulties of an infinite integral and an integrand with poles can be solved. But if this computation must be repeated for many distances, many frequencies, many loads, or many soil models, it becomes a time consuming task which is not acceptable for a user-friendly prediction tool for railway induced ground vibration. Therefore, an approximate method for the computation of the wave field has been developed. The computation consists of several steps. At first, an approximate dispersion profile is calculated according to rules which have been derived from exact solutions. Secondly, the dispersion is used to achieve the amplitude for a certain frequency and a certain distance by calculating the approximate solution of a corresponding homogeneous half-space. Thirdly, three layer corrections are added which include lowfrequency near-field effects, high-frequency far-field effects, and a resonance amplification around the layer frequency. This procedure yields the wave field due to a point load. For a train load, many of these point-load responses have to be summed up, and a frequencydependant reduction factor has to be multiplied to incorporate the effect of the load distribution along and across the track. - The prediction method is applied to real sites, and the appropriate soil models are identified by approximating the measured transfer functions (frequency-dependant amplitudes) which is presented as an alternative to the approximation of the dispersion (frequency-dependant wave velocities). These examples demonstrate the general behavior of layered soils: the low amplitudes of the stiff half-space at low frequencies, the high amplitudes of the softer layer at high frequencies, the strong increase of amplitudes and a possible resonance amplification at mid frequencies. The material damping of the layer yields a strong attenuation of the amplitudes with the distance for high frequencies. The response depends strongly on the resonance or layer frequency which is shown for different layer depths and velocities always in good agreement with measurements. The layer frequency can be of immense influence if train-speed effects are analysed in a layered soil. The good agreement with many measurements in this contribution as well as in the references validates the prediction of ground vibration based on the theory of a layered half-space.
The ground vibrations, which are generated by trains on different tracks, have been calculated by finite-element boundary-element models. The ballasted track is modelled in detail by the finite element method. The infinite soil is modelled by the boundary element method as a homogeneous or layered half-space. The track-soil system is coupled to a simple rigid mass model of the vehicle so that the vehicle-track interaction is completely included. Transfer functions are calculated in frequency domain without and with vehicle-track interaction, the compliance of the track and the mobilities of the soil at different distances from the track. Finally, the ratios between the ground vibration amplitudes with and without mitigation measures are calculated to quantify the effectiveness of the mitigation measures.
Tracks with under-sleeper pads have been investigated in a wide parameter study for the RIVAS project. The main parameters that influence the reduction of ground vibration are the stiffness of the under-sleeper pad, the mass and the width of the sleeper. The softest sleeper pad yields the best reduction of the ground vibration. The influence of the sleeper mass is not so strong, as the characteristic frequency is ruled by the mass of the sleeper and the mass of the wheelset as well.
Ground vibrations due to different technical sources are analysed in theory and experiment for the dispersion of Rayleigh waves and the admittance spectra. Both tasks are theoretically based on the same concept: The admittance function in frequencywavenumber domain yields the dispersion as its maxima, and the admittance function in space domain is obtained by integrating it over the wavenumbers. On the experimental side, many signal processing methods have been applied to many sites and have been developed by the authors in the last 35 years, i.e., time-domain methods, including the cross-correlation method, and frequency-domain methods such as the spectral analysis of surface waves with two or multiple sensors, the wavenumber-transform method, and the spatial autocorrelation method. All methods are presented by their basic formula and by at least one example site. Different sensor arrays and deterministic and stochastic sources have been tested for the spatial autocorrelation method and the wavenumber-transform method at several sites. In addition, all frequency-domain methods are presented for a specific layered site comparing their quality. The evaluated dispersion curves are very similar, but a somewhat higher frequency range has been found for the fastest method, i.e., the multi-sensor spectral-analysis-of-surface-waves method. The theoretical solutions have been used for the inversion of the measured dispersion to the soil profile of the specific layered soil. The theoretical soil model has subsequently been used to predict the ground vibration spectra of hammer and railway excitation that exhibit a good agreement with the corresponding measurements. Thus, the contribution shows the benefit of active and passive seismic methods for the prediction of railway vibration, including a new version of the spatial autocorrelation method for technical vibrations. On the other hand, technical and namely railway vibrations are considered a seismic source for the exploration of near surface soils.
Train passages induce static and dynamic forces on the track, the train-induced vibrations propagate through the soil and excite neighbouring buildings. The problem of train vibrations is divided into the parts emission, which is the excitation by railway traffic (the present contribution), transmission, which is the wave propagation through the soil, and immission, which is the transfer into a building, - The calculation of the axle loads are based on the vehicle-track-soil interaction. This interaction uses the dynamic stiffness of the vehicle (the inertia of the wheelset) and the dynamic stiffness of the track-soil System. Based on various time consuming finite-element boundary-element calculations, an approximate track-soil model has been established. The vehicle-track-soil analysis yields several transfer functions between the various geometric or stiffness irregularities and the axle loads of the train. Geometric irregularities of the vehicle (the wheels) and the track (rail surface and track alignment) are the simplest components. Geometric irregularities of the subsoil (trackbed irregularities) have to be transferred to effective irregularities at rail level. The bending stiffness of the track is filtering out the short-wavelength contribution. Stiffness irregularities occur due to random variations in the bailast or the subsoil, which must also be transferred to effective track irregularities, and due to the discrete rail support on sleepers. The axle loads due to the effective track errors from stiffness variations have their specific vehicle-track transfer function. - All necessary formula for the prediction of axle-load spectra will be presented. The prediction method is compared with axle-box measurements at a Standard ballasted track. Moreover, ground Vibration measurements at numerous sites are exploited for the axle-load spectra and the Validation of the prediction method.
An drei Straßenbrücken unterschiedlicher Länge und Bauart wurden vor Inbetriebnahme ambiente Schwingungsmessungen mit bis zu 350 Messpunkten durchgeführt, um auch höhere Eigenformen detaillierter zu ermitteln. An einer Eisenbahnbrücke der Strecke Hannover-Würzburg wurden bei Testzugfahrten mit definierten Geschwindigkeiten verschiedene Resonanzanregungen beobachtet. Dies wird mit dem Achsfolgespektrum des ganzen Zuges erklärt, wobei eher spezifische Frequenzauslöschungen als Resonanzanregungen maßgeblich sind.
The maintenance of the transport infrastructures and their further development are going to remain focal points for investment and research in Germany in future. According to the latest development forecasts made by both the federal government and Deutsche Bahn, even if rail´s percentage share of the market were to remain unchanged, growth of around 50% would be expected in the next ten years, especially in freight traffic. This growth is necessitating considerable development both in the technical design of the tracks and in the abatement of the noise and vibration caused by railway traffic.
Durch Schienenverkehr angeregte Wellenausbreitung durch den Boden - Stand der Simulationsmethoden
(2014)
The layered soil is calculated in the frequency wavenumber domain and the solutions for fixed or moving point or track loads follow as wavenumber integrals. The resulting point load solutions can be approximated by simple formula. Measurements yield the specific soil parameters for the theoretical or approximate solutions, but they can also directly provide the point-load solution (the transfer function of that site). A prediction method for the train-induced ground vibration has been developed, based on one of these site-specific transfer functions. The ground vibrations strongly depend on the regular and irregular inhomogeneity of the soil. The regular layering of the soil yields a cut-on and a resonance phenomenon, while the irregular inhomogeneity seems to be important for high-speed trains. The attenuations with the distance of the ground vibration, due to point-like excitations such as vibrator, hammer, or train-track excitations, were investigated and compared. All theoretical results were compared with measurements at conventional and high-speed railway lines, validating the approximate prediction method.
En este artículo se presentan 2 metodologías basadas en las formulaciones del Método de los Elementos de Contorno y del Método de los Elementos Finitos para estudiar el efecto de la interacción suelo-estructura en el comportamiento dinámico de edificaciones. Se ha estudiado la respuesta de un edificio de 3 plantas producida por un campo de ondas incidente con los 2 métodos propuestos. Los resultados obtenidos presentan un buen grado de acuerdo entre ellos. A partir de estos resultados se ha validado un modelo aproximado para estudiar este tipo de problemas y se han examinado diferentes tipologías de edificaciones. Las conclusiones alcanzadas muestran que la respuesta global de las estructuras se debe a la deformación de los forjados y depende de su superficie, de las condiciones de apoyo y del acoplamiento con los forjados de la misma planta. Del mismo modo, se ha observado un acoplamiento del comportamiento de pilares y forjados cuando las rigideces de ambos son similares.----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- This paper presents 2 methodologies based on the Boundary Element Method and the Finite Element Method to study soil-structure interaction effect on building behaviour. A 3-story building response induced by an incident wave field is studied using both methods. The results obtained show a good agreement. Then, a simplified model is validated from these methods and several buildings are analysed. Conclusions show that structural responses are due to floor deformation, and depend on their area, support conditions and coupling. A coupling between floors and columns when both elements have similar stiffness is also observed.
Vibration of normal apartment, office and production buildings, which are excited by technically induced ground vibrations are considered. Many wavelengths of the Rayleigh waves of the soil fit into the foundation dimensions. The related high discretization effort can nowadays be realized with detailed soil-structure interaction method. The combined finite-element boundary-element method is used here as a detatiled method. Simplified method can be used with less computation time, but these methods must be calibrated by exact results. One simplification is to extent the structure to infinity and to solve the problem by wavenumber domain methods. Another simplification is the use of a Winkler soil instead of the continuous soil. Usually, the Winkler parameters are not only soil parameters but depend also on the rigid or flexible foundation structure. Substructure methods use commercial FEM software for the building part. The contribution will show some detailed and some simplified results on large structural elements such as foundation plates, walls, storey plates on columns as well as results on complete buildings. The reduction of the ground vibration by stiff elements and the amplification due to floor or building resonances are discussed which are the most important phenomena of the soil-building interaction.
A variety of isolation measures exists to reduce the vibration in the neighbourhood of railway lines. They can be roughly classified as elastic or stiffening systems. There are the following elastic elements, rail pads or resilient fixation systems between rail and sleeper, under sleeper pads or sleeper shoes under the sleepers, and ballast mats under the ballast. Stiffening systems (plates) are used as slab tracks, floating slab tracks, or mass-spring systems. In the EU project “Railway induced vibration abatement solutions (RIVAS)”, elastic under sleeper pads have been investigated. The dynamic behaviour of the track and the surrounding soil has been calculated by the combined finite-element boundary-element method in a systematic parameter study. It has been shown that the mitigation effect can be improved by soft under sleeper pads or by heavy sleepers. Consequently, such track elements (soft under sleeper pads and heavy sleepers) have been thoroughly investigated in laboratory tests to establish the static and dynamic parameters as well as their serviceability. Finally, field tests at and near railway tracks with and without under sleeper pads have been performed. To determine the reduction effect of the isolated track, the ground vibrations excited by trains or artificial sources have been measured. The soil properties at the different sites have also been measured so that the comparison of the isolated and un-isolated track can take into account possible differences of the soil parameters. The contribution shows how the different (numerical, laboratory and field) methods and results can be combined to achieve an improved mitigation solution with soft under sleeper pads and heavy sleepers for ballasted and slab tracks.
The soilstructure interaction of elastic plates on homogeneous or layered soils excited by horizontally propagating waves is analysed. Large plates are modelled by a combined finite-element boundary-element method (FEBEM), whereas the response of infinitely long plates is calculated by a numerical integration in the frequencywavenumber domain. The finite-element boundary-element method yields the complete soilplate transfer function of frequency and distance whereas the frequencywavenumber solution of the infinitely long plate can serve as an approximation for long distances on a finitely long plate. The soilplate transfer function starts to decrease strongly at the coincidence frequency, where the bending stiffness equals the plate inertia. A strong decrease follows at mid frequencies and a strong reduction of less than 0.1 of the ground vibration is reached at high frequencies. Rules for the characteristic frequencies are derived from the numerical results clearly indicating the strongest influence of the soil stiffness and the weaker influence of the bending stiffness of the plate. The influence of the mass, length and width of the plate are shown to be limited in case of realistic parameters, but it should be noted that the reduction effects are less effective for layered soils and for nearer observation points.
The dynamics of slab tracks and floating slab tracks are analyzed by multibeam models for the track and by integration in the wave-number domain for the soil, which is modeled as a layered half-space. Frequency-dependent compliances and force transfers are calculated for a great variety of track and soil parameters. The distribution of the load and the displacements along the track is investigated as well as the wave propagation perpendicular to the track and the ground vibration amplitudes. The floating slab track has a dominating plate-mat resonance and a strong high-frequency reduction. A track-soil resonance can also be recognized for an unisolated slab track in the case of layered soils. Generally, there is a strong damping of the track by the soil. The reduction effect of the slab mat is mainly owing to the elimination of this strong damping. The continuous soil yields slightly different rules for the displacements and force densities than those of a Winkler support. The total force transfer from the rail to the soil is the best criterion to judge the effectiveness of a floating slab track in reducing the ground vibration at some distance from the railway line. The total force transfer is easier to calculate than the double Fourier integrals of the ground vibration amplitudes, namely in the far field, and it has the best correlation with the reduction of the ground vibration.
Vehicle, track and ground vibration as well as their interaction are considered in a combined finite-element boundary-element (FEBEM) approach. The layered soil is calculated in frequency wavenumber domain and the solution for fixed or moving point or track loads follow as wavenumber integrals. The soil results from the measurements and the detailed models are approximated by simple formula which are used for the prediction of train-induced ground vibration. The influence of the track and the soil on the train induced ground vibration is analysed by the detailed models. The ground vibrations strongly depend on the regular and random inhomogeneity of the soil. The regular layering of the soil yields a cut-on and resonance phenomenon while the random inhomogeneity yields a scattering of the axle impulses which proved to be important for high-speed trains. The attenuation with distance of the ground vibration due to the point-like excitations such as vibrator or hammer excitations and the train-track excitation are investigated and compared. All theoretical results are compared with measurements at conventional and high-speed railway lines.
Um die Erschütterungen infolge von Schienenverkehr zu reduzieren, werden elastische Elemente in den Eisenbahnfahrweg eingebaut: elastische Zwischenlagen zwischen Schiene und Schwelle, elastische Schwellensohlen zwischen Schwelle und Schotter und Unterschottermatten unterhalb des Schotters. Das elastische Element führt zu einer ausgeprägten Eigenfrequenz des Gesamtsystems bestehend aus Fahrzeug, Fahrweg und Untergrund. Die Wirkung der elastischen Elemente beruht darauf, dass die Frequenzen oberhalb dieser Eigenfrequenz abgemindert werden. Für die Ermittlung der Wirksamkeit der Minderungsmaßnahme werden das Gleis mit elastischem Element und das Gleis ohne elastisches Element berechnet. Beide Eisenbahnfahrwege werden mit der kombinierten Finite-Element- Randelement-Methode berechnet, wobei das Gleis einschließlich des Schotters mit der Finite-Element-Methode berechnet wird, der Gleisuntergrund hingegen mit der Randelementmethode. Für die erschütterungsmindernden Gleise erweist es sich als vorteilhaft, spezielle Gleisendelemente an den Seiten des FE-Modells anzufügen. Dadurch wird zusätzlich zur Unendlichkeit des Untergrundes auch die unendliche Länge des Gleises berücksichtigt. Für die Ermittlung der Minderungswirkung werden die frequenzabhängige Nachgiebigkeit des Gleise, die Kraftübertragung des Gleises, und die Fahrzeug-Fahrweg-Wechselwirkung berechnet. Schließlich werden die Kraftminderungen verschiedener Eisenbahnfahrwege dargestellt und der Einfluss der wesentlichen Parameter untersucht.