Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (52)
- Beitrag zu einem Tagungsband (47)
- Vortrag (46)
- Beitrag zu einem Sammelband (19)
- Posterpräsentation (4)
- Buchkapitel (1)
- Forschungsbericht (1)
Sprache
- Englisch (170) (entfernen)
Schlagworte
- Ground vibration (38)
- Layered soil (12)
- Slab track (11)
- Railway track (10)
- Mitigation (9)
- Track-soil interaction (9)
- Train passage (9)
- Vehicle-track interaction (9)
- Finite-element boundary-element method (8)
- Hammer impact (8)
- Building vibration (7)
- Layered soils (7)
- Train-induced ground vibration (7)
- Vibration measurements (6)
- Excitation forces (5)
- Field tests (5)
- Track vibration (5)
- Train speed (5)
- Vehicle-track-soil interaction (5)
- Container loading (4)
- Drop test (4)
- Finite element method (4)
- Force transfer (4)
- Foundation load (4)
- Railway (4)
- Soil-building interaction (4)
- Track damage (4)
- Wavenumber integrals (4)
- Attenuation (3)
- Axle impulses (3)
- Axle sequence (3)
- Ballast track (3)
- Base isolation (3)
- Continuously inhomogeneous soils (3)
- Filter effects (3)
- Irregular soil (3)
- Irregularities (3)
- Measurement (3)
- Measurements (3)
- Pile bending stiffness (3)
- Pile foundation (3)
- Prediction (3)
- Railway bridge (3)
- Randomly heterogeneous soil (3)
- Scattering (3)
- Soil stiffness (3)
- Train passages (3)
- Wind energy tower (3)
- ground vibration (3)
- mitigation (3)
- railway track (3)
- 2-span bridge (2)
- Achsfolgespektren (2)
- Amplitude-distance laws (2)
- Apartment building (2)
- Axle box measurements (2)
- Axle-sequence spectrum (2)
- Ballast tracks (2)
- Bauteile (2)
- Bauwerke (2)
- Boundary element method (2)
- Bridge resonance (2)
- Brücken (2)
- Displacements (2)
- Dynamic testing (2)
- Environmental vibrations (2)
- Evaluation (2)
- Finite element models (2)
- Floating slab track (2)
- Foundations (2)
- Freight train (2)
- Ground vibration measurements (2)
- Hammer tests (2)
- High-speed train (2)
- High-speed trains (2)
- Irregular ballast (2)
- Modalanalyse (2)
- Office tower (2)
- Passenger train (2)
- Plate-soil interaction (2)
- Rail roughness (2)
- Railway measurement campaign (2)
- Railway tracks (2)
- Railway tunnel (2)
- Railway vibration (2)
- Railways (2)
- Rayleigh wave (2)
- Resonance (2)
- Scattered axle impulses (2)
- Soil properties (2)
- Soil-structure interaction (2)
- Soil-wall-floor model (2)
- Static axle loads (2)
- Surface line (2)
- Surface-tunnel reduction (2)
- Track damage monitoring (2)
- Train excitation (2)
- Under-ballast plate (2)
- Varying track stiffness (2)
- Vehicle–track interaction (2)
- Vibration measurement (2)
- Vibration reduction (2)
- Wave excitation (2)
- Wavenumber method (2)
- floor vibration (2)
- modal analysis (2)
- track-soil interaction (2)
- undersleeper (2)
- wave analysis (2)
- 1-D insertion loss (1)
- Amplitude-charge weight laws (1)
- Amplitude-distance law (1)
- Assessment (1)
- Axle loads (1)
- Axle pulses (1)
- Axle-load spectra (1)
- Axle-sequence (1)
- Ballast mat (1)
- Beam dynamics (1)
- Beam-soil interaction (1)
- Bending waves (1)
- Blasting charge (1)
- Boundary element (1)
- Boundary elements (1)
- Bridge (1)
- Bridge track (1)
- Bridge vibration (1)
- Building response (1)
- Cancellation (1)
- Cars (1)
- Column/wall resonance (1)
- Combined finite-element boundary-element method (1)
- Compliance function (1)
- Components of excitation (1)
- Continuous soil (1)
- Damage detection (1)
- Damping (1)
- Dispersion (1)
- Doppler effect (1)
- Downburst (1)
- Drop height (1)
- Dynamic axle loads (1)
- Dynamic loads (1)
- Dynamic pile and pile group stiffness (1)
- Elastic length (1)
- Elastic track elements (1)
- Emission (1)
- Experimental verification (1)
- Explicit Green´s functions (1)
- Explosion (1)
- Explosion-induced ground vibrations (1)
- FEBEM and simplified methods (1)
- Fequency domain (1)
- Filter effect of the soil (1)
- Finite element (1)
- Finite-element boudnary-element method (1)
- Finite-element method (1)
- Flexibility (1)
- Flexible car body (1)
- Flexible plate (1)
- Flexible wheelset (1)
- Floor amplification (1)
- Floor resonance (1)
- Floors (1)
- Footbridge (1)
- Foundation reduction (1)
- Frequency response function (1)
- Frequency-specific attenuation (1)
- Frequency-wavenumber method (1)
- Geometric trackbed irregularities (1)
- Geometric vehicle and track irregularities (1)
- High-Rise Building (1)
- High-rise buildings (1)
- Inertial Interaction (1)
- Inertial interaction (1)
- Inhomogeneous soils (1)
- Insertion loss (1)
- Interaction (1)
- Interior load (1)
- Kinematic Interaction (1)
- Kinematic and inertial soil-pile-building (1)
- Kinematic interaction (1)
- Laboratory tests (1)
- Long-span bridge (1)
- MASW (1)
- Mass drop (1)
- Material damping (1)
- Measured railway vibrations (1)
- Measurement campaigns (1)
- Mitigation measures (1)
- Modal analysis (1)
- Modal force spectrum (1)
- Modal load spectrum (1)
- Modes (1)
- Modes and waves (1)
- Monitoring (1)
- Movin load test (1)
- Moving load (1)
- Moving loads on tracks (1)
- Multi-beam method (1)
- Multi-beam model (1)
- Multi-beam track model (1)
- Multi-beam-on-support model (1)
- Non-synoptic wind event (1)
- Obstacles (1)
- Office building (1)
- Overhead transmission line (1)
- Parametric excitation (1)
- Pile Foundation (1)
- Pile foundations (1)
- Pile groups (1)
- Pile-soil interaction (1)
- Prediction of explosion induced ground and building vibration (1)
- Prediction software (1)
- Predictions (1)
- Propagation from a tunnel (1)
- Quasi-static response; (1)
- Radiation damping (1)
- Rail pad (1)
- Railbridge (1)
- Railway forces (1)
- Railway induced ground vibration (1)
- Railway induced vibration (1)
- Railway track vibration (1)
- Railway trafiic (1)
- Random dynamics and vibrations (1)
- Random stiffness variation (1)
- Reduction (1)
- Residential building (1)
- Rigid vehicle model (1)
- SASW (1)
- SPAC (1)
- Scattering damping (1)
- Simple and fast prediction (1)
- Simple prediction (1)
- Sleeper pad (1)
- Sleeper passage (1)
- Soft track elements (1)
- Soil forces (1)
- Soil transfer function (1)
- Soil-building resonance (1)
- Soil-pile interaction (1)
- Soil-wall floor model (1)
- Static railway loads (1)
- Stiffness (1)
- Stiffness variation (1)
- Surface Foundation (1)
- Switch (1)
- Target stiffness (1)
- Track (1)
- Track alignment (1)
- Track and vehicle irregularities (1)
- Track beam (1)
- Track compliance (1)
- Track damage quantification (1)
- Track deflection (1)
- Track deformation (1)
- Track displacements (1)
- Track dynamic (1)
- Track filter (1)
- Track filtering (1)
- Track irregularities (1)
- Track-soil and vehicle-track resonances (1)
- Train configuration (1)
- Train induced ground vibration (1)
- Train-induced vibration (1)
- Tran speed (1)
- Transfer fuction (1)
- Transfer function (1)
- Trench (1)
- Tunnel (1)
- Tunnel line (1)
- Tunnel track (1)
- Tunnel vibration (1)
- Tunnel-pile transfer (1)
- Tunnel-to-surface reduction (1)
- Turnout (1)
- Under sleeper pad (1)
- Under sleeper pads (1)
- Under-sleeper pads (1)
- Varying soil stiffness (1)
- Varying stiffness (1)
- Vibration (1)
- Vibration excitation (1)
- Vibration isolation (1)
- Wave attenuation (1)
- Wave propagation (1)
- Wave theory of attenuation (1)
- Wave velocity (1)
- Wave-number integrals (1)
- Wavenumber domain (1)
- Waves (1)
- Wheel out-of-roundness (1)
- Wheelset (1)
- Wheelset accelerations (1)
- Wide sleeper (1)
- layered soil (1)
- sleeper pads (1)
Organisationseinheit der BAM
- 7 Bauwerkssicherheit (59)
- 7.2 Ingenieurbau (59)
Eingeladener Vortrag
- nein (46)
This contribution presents some principles and some examples of the mitigation of railway-induced ground vibrations. The principles are different for the mitigation measures at the track, in the soil or at the building. Force transfer functions of isolated and un-isolated track-soil systems, reflected and transmitted wave amplitudes at walls and trenches in the soil, and the transfer of the (free-field) vibration amplitudes to the foundation amplitudes of the building are analysed. The mitigation effect can be calculated by exact or simplified formulas. Some examples with 3D (finite-element boundary-element), 2D (beam-on-support), and 1D track models, 2D and 1D soil models, detailed 3D building models and finite or infinite 1D wall-floor models are investigated to find out if simple models can be used for a satisfactory prediction of the mitigation effect. The 1D track examples show that the force transfer of the track without vehicle can be exactly calculated, whereas the total force transfer can be calculated approximately if appropriate wheelset masses per track length are used for the isolated and the un-isolated track. The mitigation effect of a filled trench is calculated by a 2D finite element model and the results compare with simple transmission formula if the stiffness per area rather than the wave impedances are used for the infill material. The base isolation of a building is analysed by a detailed 3D model and the results are similar to the analytic results of a single wall with floors on the soil. Other reduction measures as different floor and column dimensions are usually less effective so that the clearly best mitigation solution at a building is a partly or a complete base isolation.
This contribution presents some principles and some examples of the mitigation of railway-induced ground vibrations. The principles are different for the mitigation measures at the track, in the soil or at the building. Force transfer functions of isolated and un-isolated track-soil systems, reflected and transmitted wave amplitudes at walls and trenches in the soil, and the transfer of the (free-field) vibration amplitudes to the foundation amplitudes of the building are analysed. The mitigation effect can be calculated by exact or simplified formulas. Some examples with 3D (finite-element boundary-element), 2D (beam-on-support), and 1D track models, 2D and 1D soil models, detailed 3D building models and finite or infinite 1D wall-floor models are investigated to find out if simple models can be used for a satisfactory prediction of the mitigation effect. The 1D track examples show that the force transfer of the track without vehicle can be exactly calculated, whereas the total force transfer can be calculated approximately if appropriate wheelset masses per track length are used for the isolated and the un-isolated track. The mitigation effect of a filled trench is calculated by a 2D finite element model and the results compare with simple transmission formula if the stiffness per area rather than the wave impedances are used for the infill material. The base isolation of a building is analysed by a detailed 3D model and the results are similar to the analytic results of a single wall with floors on the soil. Other reduction measures as different floor and column dimensions are usually less effective so that the clearly best mitigation solution at a building is a partly or a complete base isolation.
Long wooden floor beams above a ball room in an old historical palace have been analysed experimentally. The eleven beams are weakly coupled by three layers of floor boards. It has been investigated if the state (the stiffness) of the wooden beams can be determined by vibration measurements of global or preferably local modes. Hammer, heel-drop and ambient excitations have been used. The vibration modes of the structure show dominating local deformations if an impact excitation is applied. This is understood as the positive superposition of several modes which yield the maximum at the excitation point but a cancellation at more distant points. Natural modes have been estimated from these vibration modes by standard and special methods which were necessary for the high damping of the wooden floor. It has been found that all floor beams contribute to each natural mode even for a weak coupling of the beams. In addition to the modal discussion, the impact tests have also been analysed for the wave propagation and amplitude attenuation with distance. The coupling of floor beams has been studied theoretically by an analytic multiple-beam model where the coupling by translational or rotational springs and by a common support motion has been assumed.
Long wooden floor beams above a ball room in an old historical palace have been analysed experimentally. The eleven beams are weakly coupled by three layers of floor boards. It has been investigated if the state (the stiffness) of the wooden beams can be determined by vibration measurements of global or preferably local modes. Hammer, heel-drop and ambient excitations have been used. The vibration modes of the structure show dominating local deformations if an impact excitation is applied. This is understood as the positive superposition of several modes which yield the maximum at the excitation point but a cancellation at more distant points. Natural modes have been estimated from these vibration modes by standard and special methods which were necessary for the high damping of the wooden floor. It has been found that all floor beams contribute to each natural mode even for a weak coupling of the beams. In addition to the modal discussion, the impact tests have also been analysed for the wave propagation and amplitude attenuation with distance. The coupling of floor beams has been studied theoretically by an analytic multiple-beam model where the coupling by translational or rotational springs and by a common support motion has been assumed.
In the last three decades, the vibrations of many floors and bridges have been measured. The contribution shows some evaluation methods, experimental results and some modelling and theoretical results. Simple evaluation methods have been developed for single and coupled floors. Two coupled beams have been measured in good agreement with the theory. A more complex coupling model has been found for a large wooden floor in a castle consisting of six floor bays which correlates well with the measurements. Damaged and intact poles have been tested by their natural frequencies and damping values, and a fair correlation between the degree of damage and the shift of the frequency. Road bridges have been analysed in detail and some examples are presented. Railway bridges and trains are studied for resonant excitation. The risk of resonance can be estimated in frequency domain by using axle-sequence spectra of the train and the natural frequencies of the bridge. A measurement example shows the amplification, but even stronger the cancellation of the subsequent axle responses. Several high-speed trains and freight trains have been analysed for their potential resonance amplification.
In the last three decades, the vibrations of many floors and bridges have been measured. The contribution shows some evaluation methods, experimental results and some modelling and theoretical results. Simple evaluation methods have been developed for single and coupled floors. Two coupled beams have been measured in good agreement with the theory. A more complex coupling model has been found for a large wooden floor in a castle consisting of six floor bays which correlates well with the measurements. Damaged and intact poles have been tested by their natural frequencies and damping values, and a fair correlation between the degree of damage and the shift of the frequency. Road bridges have been analysed in detail and some examples are presented. Railway bridges and trains are studied for resonant excitation. The risk of resonance can be estimated in frequency domain by using axle-sequence spectra of the train and the natural frequencies of the bridge. A measurement example shows the amplification, but even stronger the cancellation of the subsequent axle responses. Several high-speed trains and freight trains have been analysed for their potential resonance amplification.
The present contribution evaluates four measuring series made by the Federal Institute of Material Research and Testing for the relations between train speed and ground vibration amplitudes. This experimental evaluation is supported by the simulation of the train passages at the different sites by using appropriate excitation mechanisms and forces as well as layered soil models which have been derived from impact measurements at each site.
The present contribution evaluates four measuring series made by the Federal Institute of Material Research and Testing for the relations between train speed and ground vibration amplitudes. This experimental evaluation is supported by the simulation of the train passages at the different sites by using appropriate excitation mechanisms and forces as well as layered soil models which have been derived from impact measurements at each site.
The present contribution evaluates four measuring series made by the Federal Institute of Material Research and Testing for the relations between train speed and ground vibration amplitudes. This experimental evaluation is supported by the simulation of the train passages at the different sites by using appropriate excitation mechanisms and forces as well as layered soil models which have been derived from impact measurements at each site.
Some results of our measurements of the Intercity experimental are presented together with simulated results and their interpretation. Three frequeny ranges could be measured and calculated: low frequencies which decrease very rapidly with distance (the quasi-static part), high frequencies (mainly due to the sleeper passage), and a mid-frequency which has the weakest attenuation with distance and is therefore dominant at the far field. Mono-frequent excitations get a wide frequency band due to the Doppler effect of the moving high-speed train.
Prediction of building noise and vibration – 3D finite element and 1D wave propagation models
(2021)
Construction work or traffic excite nearby buildings, and the perceptible or audible vibration can be a nuisance for the inhabitants. The transfer of the vibration from the free field to the building has been calculated by the finite element method for many models in consultancy and research work. The analysis for all storeys of certain building points such as walls, columns and floors unveiled some rules, some typical modes, and some wavetype responses. A simplified building-soil model has been created, which includes well these effects of building-soil resonance, wall/column resonance, floor resonances, and the high-frequency reduction. The model consists of one wall for a wall-type apartment building or a column for each specific part (mid, side or corner) of a column-type office building. The building response in the high-frequency (acoustic) region is calculated as mean values over all storeys and over wider frequency bands, by wave-type asymptotes of an infinitely tall building, and by the soil to wall ratio of impedances. The secondary noise is predicted by Transfer values between the building vibration (center of floors, walls at a room corner) and the sound pressure.
Prediction of building noise and vibration – 3D finite element and 1D wave propagation models
(2021)
Construction work or traffic excite nearby buildings, and the perceptible or audible vibration can be a nuisance for the inhabitants. The transfer of the vibration from the free field to the building has been calculated by the finite element method for many models in consultancy and research work. The analysis for all storeys of certain building points such as walls, columns and floors unveiled some rules, some typical modes, and some wavetype responses. A simplified building-soil model has been created, which includes well these effects of building-soil resonance, wall/column resonance, floor resonances, and the high-frequency reduction. The model consists of one wall for a wall-type apartment building or a column for each specific part (mid, side or corner) of a column-type office building. The building response in the high-frequency (acoustic) region is calculated as mean values over all storeys and over wider frequency bands, by wave-type asymptotes of an infinitely tall building, and by the soil to wall ratio of impedances. The secondary noise is predicted by Transfer values between the building vibration (center of floors, walls at a room corner) and the sound pressure.
Explosion-induced ground vibrations have been measured at several places. Results about the wave propagation are shown in this contribution. The particle velocities of the soil have been measured at up to 1000 m distance from the explosion and are presented as time records (seismograms) and one-third octave band spectra (transfer functions). The results are compared with the results of hammer impacts. The seismograms clearly show different wave types, compressional waves of the air, the water and the soil, and the Rayleigh wave. The hammer impacts yield good results up to 100 m and incorporate higher frequencies at about 50 Hz, whereas the explosion results in a ground vibration with frequencies around 10 Hz and a longer range of influence. Explosion and hammer excitations are evaluated for the wave velocities of the soil by using the wavenumber and the spatial auto-correlation method. The attenuation of the ground vibration amplitudes A with distance r can well be presented by a power law A ~ r -q. This type of amplitude-distance law and the corresponding power q > 1 are substantiated in the contribution. The influence of the charge weight W is evaluated as an additional power law A ~ W -p for each measuring site. The power is found quite similarly around q 0.6 as all sites have a medium soft soil such as sand and clay. The obtained amplitude-charge-distance law can be used to predict the explosion-induced ground and building vibrations at other sites.
A simple and fast prediction scheme is presented for train-induced ground and building vibrations. For the emission, finite-element boundary-element or multiple-beam-on-continuous-soil models of the track have been analysed and approximated by faster track-on-Winkler-soil models. The vehicle-track interaction due to irregularities yields the excitation forces. For the transmission of waves in the soil, the wavenumber integral of the compliance of layered soils has been evaluated. The calculation time is reduced for the prediction by using the solution of a homogeneous half-space with a frequency-dependent wave velocity (the dispersion) of the soil. For the immision, many 2 and 3-dimenisonal finite-element building models have been investigated, and a good approximation has been established by a 1-dimensional soil-wall-floor model. In addition, the axle sequence of the train, the quasi-static and the “scattered” response of the soil, and the wave propagation from a tunnel to a pile foundation of a building have been included.
A simple and fast prediction scheme is presented for train-induced ground and building vibrations. For the emission, finite-element boundary-element or multiple-beam-on-continuous-soil models of the track have been analysed and approximated by faster track-on-Winkler-soil models. The vehicle-track interaction due to irregularities yields the excitation forces. For the transmission of waves in the soil, the wavenumber integral of the compliance of layered soils has been evaluated. The calculation time is reduced for the prediction by using the solution of a homogeneous half-space with a frequency-dependent wave velocity (the dispersion) of the soil. For the immision, many 2 and 3-dimenisonal finite-element building models have been investigated, and a good approximation has been established by a 1-dimensional soil-wall-floor model. In addition, the axle sequence of the train, the quasi-static and the “scattered” response of the soil, and the wave propagation from a tunnel to a pile foundation of a building have been included.
Train passages induce static and dynamic forces on the track, the train-induced vibrations propagate through the soil and excite neighbouring buildings. The problem of train vibrations is divided into the parts emission, which is the excitation by railway traffic (the present contribution), transmission, which is the wave propagation through the soil, and immission, which is the transfer into a building, - The calculation of the axle loads are based on the vehicle-track-soil interaction. This interaction uses the dynamic stiffness of the vehicle (the inertia of the wheelset) and the dynamic stiffness of the track-soil System. Based on various time consuming finite-element boundary-element calculations, an approximate track-soil model has been established. The vehicle-track-soil analysis yields several transfer functions between the various geometric or stiffness irregularities and the axle loads of the train. Geometric irregularities of the vehicle (the wheels) and the track (rail surface and track alignment) are the simplest components. Geometric irregularities of the subsoil (trackbed irregularities) have to be transferred to effective irregularities at rail level. The bending stiffness of the track is filtering out the short-wavelength contribution. Stiffness irregularities occur due to random variations in the bailast or the subsoil, which must also be transferred to effective track irregularities, and due to the discrete rail support on sleepers. The axle loads due to the effective track errors from stiffness variations have their specific vehicle-track transfer function. - All necessary formula for the prediction of axle-load spectra will be presented. The prediction method is compared with axle-box measurements at a Standard ballasted track. Moreover, ground Vibration measurements at numerous sites are exploited for the axle-load spectra and the Validation of the prediction method.
Train-induced ground vibrations are generated by static and dynamic axle loads which can be calculated by vehicle-track-soil models and the vehicle and track irregularities. A fast prediction method has been developed which uses approximate transfer functions of layered soils. In the present contribution, this prediction method is used for the inverse calculation of the axle-load spectra from the measured ground vibration. The layered soils of some measuring sites show very differing ground vibration spectra in the amplitude range of 0.0001–1.0 mm/s as a consequence of the soft layer and stiff half-space, differing layer frequencies, as well as the far- and near-field measuring points. The back-calculation, however, yields axle-load spectra within a single order of magnitude around 1 kN. Axle-box measurements confirm the amplitude level of the axle loads. This standard axle-load spectrum can be used for a basic prediction at a new site. The separation of train and site-specific components allows a better evaluation of railway vibrations, for example, of different trains and different tracks. By eliminating the effects of differing soil characteristics, an important mid-frequency component has been found which lies between 8 and 32 Hz depending on the train speed. The origin of this dominant mid-frequency component is discussed using advanced prediction methods like moving constant loads, scattered axle impulses and axle-sequence spectra.
The reduction in train-induced ground vibrations by different railway lines and by mitigation measures in the propagation path was analysed in a unified approach by two-dimensional finite element calculations. In general, there was no reduction at low frequencies, and the reduction be-came stronger with increasing frequencies. A maximum reduction of 0.1 at high frequencies was established with an open trench. Reductions between 0.7 and 0.2 have been found for the other sit-uations, filled trenches, walls, plates, and blocks, as well as for railway lines on dams, in cuts and in a tunnel. Bridges can produce amplifications due to their resonance frequencies, but also strong reductions due to massive bridge piers. The influence of some parameters has been analysed, such as the bridge span, the inclination of the dam and the cut, the stiffness of the soil, and the tunnel structure. The dynamic track stiffnesses of a surface, bridge, and tunnel track have been calculated using the 3D finite-element boundary-element method for comparison with corresponding meas-urements.
In this article, the passage of different trains over different bridges will be studied for resonant excitation. The intensity of the resonance will be estimated in frequency domain by using three separated spectra. At first, the excitation spectrum of the modal forces is built by the mode shape and the passage time of the train over the bridge. The second spectrum is the frequency response function of the bridge which include the modal frequency, damping and mass. The third part is the spectrum of the axle sequence of the train. The influences of train speed, bridge length, bridge support, track irregularities, and train type on the resonance amplitudes will be analysed for each of these spectra separately for getting a better insight. A variety of axle-sequence spectra and corresponding rules will be presented for different vehicles and trains. As examples, the passage of a slow freight train over a long-span bridge, a normal passenger train over a medium-span bridge, and a high-speed train over a short bridge will be analysed. Corresponding measurements show the amplification, but also the cancellation of the subsequent axle responses. Namely in one of the measurement examples, the first mode of the bridge was amplified and the second mode was cancelled at a low speed of the train and vice versa at a higher speed.
The soilstructure interaction of elastic plates on homogeneous or layered soils excited by horizontally propagating waves is analysed. Large plates are modelled by a combined finite-element boundary-element method (FEBEM), whereas the response of infinitely long plates is calculated by a numerical integration in the frequencywavenumber domain. The finite-element boundary-element method yields the complete soilplate transfer function of frequency and distance whereas the frequencywavenumber solution of the infinitely long plate can serve as an approximation for long distances on a finitely long plate. The soilplate transfer function starts to decrease strongly at the coincidence frequency, where the bending stiffness equals the plate inertia. A strong decrease follows at mid frequencies and a strong reduction of less than 0.1 of the ground vibration is reached at high frequencies. Rules for the characteristic frequencies are derived from the numerical results clearly indicating the strongest influence of the soil stiffness and the weaker influence of the bending stiffness of the plate. The influence of the mass, length and width of the plate are shown to be limited in case of realistic parameters, but it should be noted that the reduction effects are less effective for layered soils and for nearer observation points.
Two measurement campaigns of train-induced ground vibrations are evaluated for the vehicle-track-soil interaction. Ground vibrations, track vibrations and vehicle vibrations have been measured for train passages and impulse excitation and compared with theoretical results. The soil and the track-soil system are calculated by wavenumber integrals. The influence of the vehicle is introduced by a substructure method. By comparing theory and measurement the different components of excitation force and ground vibration can be analysed, the quasi-static excitation, track-alignment errors, the out-of-roundness of wheels, the wheel and rail roughness, and moreover, scattered axle impulses and ineffective high-frequency parts of the wheelset accelerations and forces.
Seismic reponse of three-dimensional structures using a Green's function approach to the soil
(1986)
Seismic response of three-dimensional structures using a green's function approach to the soil
(1986)
Simple and advanced boundary-element method for the soil and its application to railway dynamics
(2007)
Simple and advanced boundary-element method for the soil and its application to railway dynamics
(2007)
A simple and fast prediction scheme is presented for train induced ground and building vibrations. Simple models such as (1-dimensional) transfer matrices are used for the vehicle-track-soil interaction and for the building-soil interaction. The wave propagation through layered soils is approximated by a frequency-dependent homogeneous half-space. The prediction is divided into the parts “emission” (excitation by railway traffic), “transmission” (wave propagation through the soil) and “immission” (transfer into a building). The link between the modules is made by the excitation force between emission and transmission, and by the free-field vibration between transmission and immission. All formula for the simple vehicle-track, soil and building models are given in this article. The behaviour of the models is demonstrated by typical examples, that is the mitigation of train vibrations by elastic track elements, the low- and high-frequency cut-offs characteristic for layered soils, and the interacting soil, wall and floor resonances of multi-storey buildings. It is shown that the results of the simple prediction models can well represent the behaviour of the more time-consuming detailed models, the finite-element boundary-element models of the track, the wavenumber integrals for the soil, and the three-dimensional finite-element models of the building. In addition, measurement examples are given for each part of the prediction confirming that the methods provide reasonable results. As the prediction models are fast in calculation, many predictions can be done, for example to assess the environmental effect along a new railway line. The simple models have the additional advantage that the user needs to know only a minimum of parameters. So, the prediction is fast and user-friendly, but also theoretically and experimentally well-founded.
A complex measuring campaign has been performed including the simultaneous measurement of vehicle, track, and soil vibrations during train runs at 16, 25, 40, 63, 80, 100, 125, 140, 160 km/h, and impulse measurements of the passenger car, three track sections and the soil. A ballast track on the soil surface and on a concrete bridge have been investigated as well as a slab track in a tunnel. The evaluation and comparison of all these data shows a generally good agreement for all components if the strong low- and high-frequency cut-off characteristics of the layered and damped soil are incorporated. There is a strong causal correlation between the vehicle and the soil by the dynamic excitation forces and a weak relation between the track and the soil by the axle-sequence spectrum of the train. However, the similarity between the axle-impulse spectrum observed at the track and the spectra of the ground vibration lead to the special excitation component of “scattered axle impulses” which is pre-dominant at the far-field points of the soil.
The propagation of ground vibrations is theoretically analysed with frequency-wavenumber and simplified methods. Experimental methods are presented which can characterise the site-specific ground vibrations by wave velocities, stiffness and damping. Measurements with hammer and train excitation have been performed at several sites. The one-third octave spectra show the stiffness-dependent amplitudes and the low- and high-frequency filter effects due to the layering and the damping of the soil. Specific train effects, an additional high-frequency filter, the sleeper passage frequency, and an amplified mid-frequency component can be clearly found. The attenuation with distance is analysed in detail where the theoretical exponential and the empirical frequency-dependent power law are considered. Hammer and train excitation show the same site-specific effects which are mainly due to the stronger or weaker damping of the soil. The train attenuation is generally weaker than the hammer attenuation. The attenuation exponent of the power law, which is strongly dependent on the site and the frequency, is reduced for the train vibration by 0.3 to 0.5 in agreement with the theory. Reasons are discussed for the overall power law and for the dominating mid-frequency component.
This contribution intends to give an overview on the vibration behaviour of slab tracks in comparison of measurements and calculations and also by comparison of different track types at more than ten different measuring sites.
In theory, tracks on continuous soil are calculated by the frequency-wavenumber domain method. In experiment, geophone measurements are transformed to displacement results. Two aspects of track behaviour are considered, the frequency-dependant compliance of the track, measured by hammer impact, and the deflection under a passing axle load. In theory, the response to a single axle can be calculated, whereas in experiment, only the passage of the whole train can be measured. For comparison of theory and experiment, the calculated deflection under a single axle is superposed to get the response of the whole train. As a result, the slab track characteristics are completely different from the ballast track characteristics where each axle can be seen in the time histories. The slab track has a more global behaviour where only a whole bogie can be found in the track response and moreover, the two neighbouring bogies are not completely separated. The measurement of the different track elements (rail, sleeper, track plate, base layer) and the frequency-dependant compliances with possible resonances yield further information About the properties of the track elements. The calculations show that the soil has the dominant influence on the amplitudes and the width of the track-plate displacements. In the measurement results, the following
parameters are analysed: slab track vs. ballast track, different types of slab tracks, damaged slab tracks, different trains, switches at different measuring points, voided sleepers, an elastic layer, the mortar layer, and different soils at different places. Finally, a good agreement between measured and calculated results is found for the normal and some special (damaged, floating) slab tracks.
The soil-foundation-structure interaction is always important when building vibrations due to train passages have to be considered. The frequency range for train vibrations is up to 100 Hz. Normally, soft surface soils are crucial so that the wavelength can be much smaller than the foundation dimensions. Three topics are of interest for the prediction and the under-standing of building vibrations. 1. The „kinematic interaction“ or the „added foundation ef-fect“, which is calculated either by the combined boundary-element finite-element method or by the wavenumber domain method, results in a reduction of the free-field vibration. The stiff-ness of the foundation resists the wave deformation, plates and walls for horizontally propa-gating waves or piles for vertically incident waves. 2. The „inertial interaction“ or the „added building effect“ yields an amplification around the vertical building resonance, which may be a rigid mode on the compliant soil or a flexible mode for high-rise buildings, and a reduction at higher frequencies. This has been analysed by detailed finite element models of apartment and office buildings. 3. Base isolation is a method to further reduce building vibrations. It is important to know the soil-foundation impedance for the possible reduction, as well as the correct building impedance. A high-rise building cannot be considered as a rigid mass model. It has a frequency-dependent behaviour with longitudinal waves travelling from the founda-tion to the top of the building which include the effect of floor vibrations. Experiences from building projects in Vienna, Frankfort and Berlin will give some additional results for the ex-citation from tunnel lines, the kinematic response of pile foundations, and the inertial re-sponse of the flexible multi-storey buildings.
The soil-foundation-structure interaction is always important when building vibrations due to train passages have to be considered. The frequency range for train vibrations is up to 100 Hz. Normally, soft surface soils are crucial so that the wavelength can be much smaller than the foundation dimensions. Three topics are of interest for the prediction and the under-standing of building vibrations. 1. The „kinematic interaction“ or the „added foundation ef-fect“, which is calculated either by the combined boundary-element finite-element method or by the wavenumber domain method, results in a reduction of the free-field vibration. The stiff-ness of the foundation resists the wave deformation, plates and walls for horizontally propa-gating waves or piles for vertically incident waves. 2. The „inertial interaction“ or the „added building effect“ yields an amplification around the vertical building resonance, which may be a rigid mode on the compliant soil or a flexible mode for high-rise buildings, and a reduction at higher frequencies. This has been analysed by detailed finite element models of apartment and office buildings. 3. Base isolation is a method to further reduce building vibrations. It is important to know the soil-foundation impedance for the possible reduction, as well as the correct building impedance. A high-rise building cannot be considered as a rigid mass model. It has a frequency-dependent behaviour with longitudinal waves travelling from the founda-tion to the top of the building which include the effect of floor vibrations. Experiences from building projects in Vienna, Frankfort and Berlin will give some additional results for the ex-citation from tunnel lines, the kinematic response of pile foundations, and the inertial re-sponse of the flexible multi-storey buildings.
The resonances of railway bridges have often been analysed for short bridges under periodical high-speed trains, for simply supported one-span bridges, for the fundamental bridge mode, and by time-domain analyses. Many time-consuming calculations have been performed to establish simplified rules for standards. In this contribution, the passage of different (existing, new and hypothetic) trains over different bridges will be analysed in frequency domain by using three separated spectra with the purpose to get a better physical insight in the phenomena. At first, the excitation spectrum of the modal forces is built by the mode shape and the passage time of the train over the bridge. The second spectrum is the frequency response function of the bridge which include the modal frequency, damping and mass. The third part is the spectrum of the axle sequence of an arbitrary train which is not limited to periodical or specific (conventional, articulated, regular or standard) trains and which does not include any bridge parameters. The final solution in frequency domain is obtained as the product of these three complex, strongly varying spectra for the dominating bridge mode or in general as the sum of these products over all relevant bridge modes. The time domain solution is obtained via the inverse Fourier transform, and the resulting time histories have been successfully compared with some measurement results. The method is applied to the vertical and torsional modes of a mid-long 1-span bridge on elastomeric bearings under standard train speeds, and to a long multi-span integral bridge under long periodical freight trains. Different resonance and cancellation effects have been found for systematically varied train speeds according to the axle sequence of the whole train which is dominated by the two locomotives in that case. To be more specific, the first torsional mode of the mid-span bridge is excited for a train speed of 100 km/h whereas the second bending mode is excited for a train speed of 160 km/h. In both cases, the other mode is suppressed by the minima of the axle-distance spectra. In addition, the case of the German high-speed train ICE4 and the very high-speed hyperloop case will be discussed briefly. In general, it is shown that resonance effects are also worth to be studied for freight and passenger trains with lower speeds.
The resonances of railway bridges have often been analysed for short bridges under periodical high-speed trains, for simply supported one-span bridges, for the fundamental bridge mode, and by time-domain analyses. Many time-consuming calculations have been performed to establish simplified rules for standards. In this contribution, the passage of different (existing, new and hypothetic) trains over different bridges will be analysed in frequency domain by using three separated spectra with the purpose to get a better physical insight in the phenomena. At first, the excitation spectrum of the modal forces is built by the mode shape and the passage time of the train over the bridge. The second spectrum is the frequency response function of the bridge which include the modal frequency, damping and mass. The third part is the spectrum of the axle sequence of an arbitrary train which is not limited to periodical or specific (conventional, articulated, regular or standard) trains and which does not include any bridge parameters. The final solution in frequency domain is obtained as the product of these three complex, strongly varying spectra for the dominating bridge mode or in general as the sum of these products over all relevant bridge modes. The time domain solution is obtained via the inverse Fourier transform, and the resulting time histories have been successfully compared with some measurement results. The method is applied to the vertical and torsional modes of a mid-long 1-span bridge on elastomeric bearings under standard train speeds, and to a long multi-span integral bridge under long periodical freight trains. Different resonance and cancellation effects have been found for systematically varied train speeds according to the axle sequence of the whole train which is dominated by the two locomotives in that case. To be more specific, the first torsional mode of the mid-span bridge is excited for a train speed of 100 km/h whereas the second bending mode is excited for a train speed of 160 km/h. In both cases, the other mode is suppressed by the minima of the axle-distance spectra. In addition, the case of the German high-speed train ICE4 and the very high-speed hyperloop case will be discussed briefly. In general, it is shown that resonance effects are also worth to be studied for freight and passenger trains with lower speeds.
Offshore wind energy towers are dynamically loaded by waves and wind. Pile foundations provide stiffness and damping and should be properly calculated. A combined finite-element boundary-element method for the dynamic interaction of flexible structures and the soil has been developed. The flexible structures such as single piles or complete wind energy towers are modeled by the finite element method whereas the homogeneous or layered soil is modeled by the boundary element method which uses the Green’s functions for interior loads in the layered half-space to establish the dynamic stiffness matrix of the soil. Soils with a stiffness that is continuously increasing with depth can be modeled as multi-layer soils with step-wise increasing stiffness. The effects of different parameters such as the stiffness of the soil, the axial and bending stiffness of the pile, and the radius of the cylindrical contact area will be analysed for the different components of excitation (vertical, horizontal, rotation and coupling). The results can be determined as specific power laws which are different for the different load cases and for the different soil models (Winkler support, homogeneous continuum, continuum with increasing stiffness). The dynamic effect of radiation damping will be analysed by the frequency-dependent compliance functions. A clear layering of the soil can cause noticeable changes in the dynamic compliances as reductions of the stiffness and the damping in certain frequency ranges (below and around layer resonance frequencies). The distribution of the displacements along the pile help to explain the observed laws. An example of an offshore wind energy tower has been modeled and calculated for wind, wave and weight loads. The resonances of the tower are usually limited by the radiation damping which is strongest for a soft soil.
Offshore wind energy towers are dynamically loaded by waves and wind. Pile foundations provide stiffness and damping and should be properly calculated. A combined finite-element boundary-element method for the dynamic interaction of flexible structures and the soil has been developed. The flexible structures such as single piles or complete wind energy towers are modeled by the finite element method whereas the homogeneous or layered soil is modeled by the boundary element method which uses the Green’s functions for interior loads in the layered half-space to establish the dynamic stiffness matrix of the soil. Soils with a stiffness that is continuously increasing with depth can be modeled as multi-layer soils with step-wise increasing stiffness. The effects of different parameters such as the stiffness of the soil, the axial and bending stiffness of the pile, and the radius of the cylindrical contact area will be analysed for the different components of excitation (vertical, horizontal, rotation and coupling). The results can be determined as specific power laws which are different for the different load cases and for the different soil models (Winkler support, homogeneous continuum, continuum with increasing stiffness). The dynamic effect of radiation damping will be analysed by the frequency-dependent compliance functions. A clear layering of the soil can cause noticeable changes in the dynamic compliances as reductions of the stiffness and the damping in certain frequency ranges (below and around layer resonance frequencies). The distribution of the displacements along the pile help to explain the observed laws. An example of an offshore wind energy tower has been modeled and calculated for wind, wave and weight loads. The resonances of the tower are usually limited by the radiation damping which is strongest for a soft soil.
The dynamics of un-isolated and isolated ballast tracks have been analysed by multi-beam models for the track and by a layered half-space model for the soil. The solution is calculated in frequency-wavenumber domain and transformed back to space domain by a wavenumber integral. This is a faster method compared to other detailed track-soil interaction methods and almost as fast as the widely used Winkler-soil method, especially if the compliances of the soil have been stored for repeated use. Frequency-dependent compliances and force transfer functions have been calculated for a variety of track and soil parameters. The ballast has a clear influence on the high-frequency behaviour whereas the soil is dominating the low-frequency behaviour of the track. A layering of the soil may cause a moderate track-soil resonance whereas more pronounced vehicle-track resonances occur with elastic track elements like rail pads, sleeper pads and ballast mats. Above these resonant frequencies, a reduction of the excitation forces follows as a consequence. The track deformation along the track has been analysed for the most interesting track systems. The track deformation is strongly influenced by the resonances due to layering or elastic elements. The attenuation of amplitudes and the velocity of the track-soil waves change considerably around the resonant frequencies. The track deformation due to complete trains have been calculated for different continuous and Winkler soils and compared with the measurement of a train passage showing a good agreement for the continuous soil and clear deviations for the Winkler soil model.