Filtern
Erscheinungsjahr
Dokumenttyp
- Vortrag (30)
- Beitrag zu einem Tagungsband (27)
- Buchkapitel (9)
- Zeitschriftenartikel (5)
- Posterpräsentation (3)
- Beitrag zu einem Sammelband (1)
Sprache
- Englisch (38)
- Deutsch (34)
- Mehrsprachig (2)
- Italienisch (1)
Referierte Publikation
- nein (75) (entfernen)
Schlagworte
- Baustoffe (5)
- Autoclaved aerated concrete (AAC) (4)
- Earth block masonry (4)
- Earthen materials (4)
- Lehmbau (4)
- Rammed earth (4)
- Strengthening (4)
- Ultra-high performance concrete (UHPC) (4)
- Building Materials (3)
- Building materials (3)
- Cellular lightweight concrete (CLC) (3)
- Composite panels (3)
- Masonry tower (3)
- Seismic assessment (3)
- Adobe masonry (2)
- Ambient vibration tests (2)
- Compression behaviour (2)
- Cultural heritage (2)
- Diagonal compression test (2)
- Dynamic characterisation (2)
- Earth block (2)
- Earth construction (2)
- Earth masonry (2)
- Earthen Materials (2)
- Einpressmörtel (2)
- Finite element method (2)
- Grout mortar (2)
- Historical buildings (2)
- Historische Bauwerke (2)
- Hydraulic lime (2)
- Instandsetzung (2)
- Kalkhydrat (2)
- Lehmmauerwerk (2)
- Lehmsteinmauerwerk (2)
- Masonry towers (2)
- Material test (2)
- Mechanical behaviour (2)
- Mechanische Eigenschaften (2)
- Repair (2)
- Shear Behaviour (2)
- Shear behaviour (2)
- Shear strength (2)
- Stampflehm (2)
- Standards (2)
- Structural identification (2)
- AAC (1)
- Adobe (1)
- Aerogel (1)
- Ambient vibration measurements (1)
- Anchor pins (1)
- Ankerauszugsversuche (1)
- Ankertraglast (1)
- Autoclaved aerated concrete (1)
- Bemessung (1)
- Bond strength (1)
- Brickwork masonry (1)
- Cellular lightweight concrete ^ (1)
- Cob (1)
- Composite UHPC elements (1)
- Compressed earth blocks (1)
- Compression Behaviour (1)
- Compression and shear testing (1)
- Compressive strength (1)
- Crack pattern (1)
- Cracks (1)
- Cracks repair (1)
- Cultural Heritage protection (1)
- Cyclic tests (1)
- Cyclinc loading (1)
- Diagonal compression tests (1)
- Digital Image Correlation (1)
- Digital image corelation (1)
- Digital image correlation (1)
- Disaster risk reduction strategies (1)
- Druck- und Schubbeanspruchung (1)
- Druck- und Schubprüfung (1)
- Druckfestigkeit (1)
- Druckversuche (1)
- Dynamic identification (1)
- Dynamic loads (1)
- Earth blocks (1)
- Earth mortar (1)
- Earthen Structures (1)
- Earthen architecture (1)
- Earthen building materials (1)
- Environmental vibration tests (1)
- Erhaltung des kulturellen Erbes (1)
- Experimental tests (1)
- F.E.M. Modellierung (1)
- FEM analysis (1)
- FEM-Analyse (1)
- Facade composite panels (1)
- Facade panels (1)
- Failure mode (1)
- Feuchteabhängige Festigkeit (1)
- Finite Element Method (1)
- Finite element analysis (FEA) (1)
- Geopolymer binders (1)
- Grouting (1)
- Historical Buildings (1)
- Historische Gebäude (1)
- Hydraulic lime based grout (1)
- Hygrothermal behaviour (1)
- Inelastic torsion (1)
- Initial shear strength (1)
- Irregular buildings (1)
- Lehmstein (1)
- Lehmstein Mauerwerk (1)
- Lime mortar (1)
- Masonry (1)
- Mauerwerk (1)
- Mechanical behavior (1)
- Mechanical properties (1)
- Model tuning (1)
- Model updating (1)
- Modified earth plaster (1)
- Normung (1)
- Partial safety factors (1)
- Polyester fabric strips (1)
- Production technology (1)
- Prüfverfahren (1)
- Pull-out test (1)
- Risk analysis (1)
- Risk management (1)
- Rissmuster (1)
- Safety factors (1)
- Sand-lime block (1)
- Sandwich elements (1)
- Schubversuche (1)
- Seismic resistance (1)
- Seismic response (1)
- Shear bond test (1)
- Shear-compression tests (1)
- Slef-cleaning properties (1)
- Static loads (1)
- Statische Druck- und Schubbeanspruchung (1)
- Teilsicherheitsbeiwert (1)
- Test procedures (1)
- Textile reinforced concrete (TRC) (1)
- Triplet test (1)
- UHPC (1)
- Ultra-high performance concrete (1)
- Uniaxial compression test (1)
- Verbundfestigkeit (1)
- Verpressanker (1)
- Versagensart (1)
- Vulnerability (1)
- Wellerlehm (1)
- Ziegelmauerwerk (1)
- Zuverlässigkeit (1)
- Zyklische Belastung (1)
- ambient vibration tests (1)
- autoclaved aerated concrete (1)
- autoclaved aerated concrete (AAC) (1)
- cellular lightweight concrete (1)
- cellular lightweight concrete (CLC) (1)
- dynamic characterisation (1)
- earth block masonry (1)
- facade composite panels (1)
- historical earthen building (1)
- masonry towers (1)
- material characterisation (1)
- partial safety factors (1)
- photocatalysis (1)
- rammed earth (1)
- seismic assessment (1)
- self-cleaning (1)
- self-cleaning properties (1)
- static monitoring (1)
- super hydrophobicity (1)
- ultra-high performance concrete (UHPC) (1)
- uniaxial compression test (1)
Organisationseinheit der BAM
- 7 Bauwerkssicherheit (4)
- 7.1 Baustoffe (4)
Eingeladener Vortrag
- nein (30)
The repair of earthen structures is not an easy task. Earth as a construction material has comparatively weak mechanical properties. It is also susceptible towards liquid water, were it can lose cohesion very quickly if certain moisture contents are exceeded. Repair concepts of structures built with such materials are therefore challenging. Historical earthen structures often exhibit damages in form of extensive cracking, which may have been caused by static or dynamic loads. Frequently these cracks are insufficiently or inappropriately repaired because of lack of knowledge and / or technology. In particular, the behaviour of crack repair by grouting poses a challenge in earthen materials and demands specific requirements for the grouting mortar, such as low water content, good water retention, low shrinkage. Grouting materials require additional specifications such as compatible strengths and Young’s modulus as well as good adhesion to the earthen substrates. In addition, grouts have to be sufficiently flowable to fill small cracks and voids without segregation or bleeding. Therefore, the rheological behaviour has to be well understood and controlled to gain the desired effects.
The repair of cracks in earthen buildings is traditionally done by stuffing manually mortar into the gap. Naturally, this method is only usable for cracks with large widths. Another disadvantage is that cracks going through thicker walls cannot be completely reached by the tools used for stuffing the mortar into the crack. Lime based grouts for earthen materials were usually used for re-attachment of plasters but less for structural reasons. Due to the nature of earthen materials grouts based on formulated or hydraulic lime (according to the definition in EN 459-1) have to meet considerable demands on a variety of properties, which are related to compatibility, durability and in particular to the ability of being injected. The goal of this study was to create a grout, which can be used to re-establish structural continuity in cracked earthen masonry or other massive earth walls (rammed earth and cob) with the focus on grouting cracks. The grout material was based on hydrated lime (calcium hydroxide) with additions of pozzolana and lime stone filler.
Traditional earthen structures of cultural value are often damaged by static or dynamic loads. This is usually manifested by the appearance of cracks. All too often these cracks are insufficiently or inappropriately repaired if at all because of lack of knowledge and/or technology. In particular, the behavior of crack repair by grouting poses a challenge in earthen materials and demands specific requirements for the grouting mortar, such as low water content, good water retention, low shrinkage, etc. If dynamic loads, e.g. induced by earthquakes, are expected, the grouting material requires additional specifications such as a compatible strength and modulus of elasticity as well as good adhesion to the earthen materials. The study presents results from the development of a grouting material based on hydraulic lime mortar suitable for the repair of cracks in a variety of earthen building techniques. The goal was to develop a material also compatible with earthen structures exposed to dynamic load. The grouting mortar was designed to be adaptable in strength properties and at the same time to have sufficient robustness for the use on the construction site. First results show a satisfactory performance of the grout concerning fresh and hardened mortar properties as well as injectability. The study is part of our work in the framework of the ongoing project NIKER, funded by the European Commission dealing with improving imovable Cultural Heritage assets against the risk of earthquakes.
This study presents diagnostic techniques to assess the structural vulnerability of earthen buildings. Medieval structures at Ambel (near Zaragoza, Spain), once a preceptory or monastic house belonging to the Military Orders, provide a useful case study. After more than a thousand years of construction, failure and repair from the 10th century to the present day, Ambel preceptory today is characterised by marked inhomogeneities: construction materials and structural typologies are juxtaposed, with structural discontinuities at the interfaces between construction phases. This paper argues that, while static analysis is an essential prerequisite before a suitable maintenance program can be defined, no evaluation of the structural behaviour of any historic building can ignore an understanding of the building’s history.
The goal of the present study is to assess the feasibility to develop a first reliable database of materials parameters for Earth Block Masonry (EBM). The database is crucial when defining the materials safety factors. In the first part an experimental campaign of compressive tests were carried out on two types of earth block and two types of earth mortar. The results showed that the mean variation of the compressive strength was remarkably less than expected. This low variation is related to a production with high quality standards of the materials employed. In the second part a partial safety factor for EBM under uniaxial compression was determined through the reliability method. The results proved the reliability of a common calculation method for EBM based on partial safety factors following the current standards.
The goal of the present study is to assess the feasibility to develop a first reliable database of materials parameters for Earth Block Masonry (EBM). The database is crucial when defining the materials safety factors. In the first part an experimental campaign of compressive tests were carried out on two types of earth block and two types of earth mortar. The results showed that the mean variation of the compressive strength was remarkably less than expected. This low variation is related to a production with high quality standards of the materials employed. In the second part a partial safety factor for EBM under uniaxial compression was determined through the reliability method. The results proved the reliability of a common calculation method for EBM based on partial safety factors following the current standards.
Das Wissen über die Materialeigenschaften und die Versagensmechanismen bei Lehmbaustoffen ist begrenzt und lückenhaft. Im Rahmen des EU-Projekts NIKER (www.niker.eu) wurden deshalb die mechanischen Eigenschaften von Bauteilen aus Lehm unter statischer Druck- und Schubbeanspruchung bestimmt. Ziel der Untersuchungen war es, grundlegende Daten zum Verformungs- und Versagensverhalten von Lehmbauteilen zu erhalten und dieses mit einem numerischen Modell zu beschreiben. Die Versuchsergebnisse belegten das spröde Verhalten von Lehmsteinmauerwerk bei uniaxialer Druckbelastung und zeigten, dass das Versagen von Lehmsteinmauerwerk infolge Schubbelastung nach Erstrissbildung in Mörtelfugen und Lehmsteinen durch Gleiten der Lehmsteine entlang der Mörtelfugen erfolgt. Die numerische Makromodellierung erbrachte zwar befriedigende Resultate hinsichtlich des Spannungs-Dehnungs-Verhaltens, jedoch konnte bei der simulierten Rissbildung keine Übereinstimmung mit den in den Versuchen beobachteten Rissbildern erzielt werden. Bei Lehmsteinmauerwerk ist also eine wesentlich aufwendigere Mikromodellierung notwendig, um das Versagensverhalten korrekt beschreiben zu können.--------------------------------------------------------------------------------------------------------------
Knowledge of the material properties and failure mechanisms of earthen materials is limited and scattered. Within the framework of the NIKER project (www.niker.eu) funded by EC, the mechanical properties of earthen material elements were therefore determined under static compression and shear loads. The aim was to obtain fundamental data on deformation behaviour and failure mechanisms of earthen material structural elements and to describe them by means of a numerical model. The test results confirmed the brittle behaviour of earth block masonry under monoaxial compressive load and showed that the failure of earth block masonry under shear load occurs by sliding of the earth blocks along the mortar joints after initial cracking in mortar joints and earth block. Numerical macro modelling showed satisfying results with regard to stress-strain behaviour, but the simulated crack pattern was not consistent with experimental observations. In the case of earth block masonry, it is thus necessary to use micro modelling approaches in order to correctly predict the failure process at local level.