Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (80) (entfernen)
Sprache
- Englisch (80) (entfernen)
Schlagworte
- Additive manufacturing (17)
- Additive Manufacturing (13)
- 3D printing (6)
- Ceramics (6)
- Bone regeneration (4)
- Ceramic (4)
- Computed tomography (4)
- Microstructure (4)
- Porosity (4)
- 3D-Printing (3)
- 3D-printing (3)
- Glass-ceramic (3)
- Sintering (3)
- Additive Fertigung (2)
- Binder Jetting (2)
- Binder jetting (2)
- Bioactive glass (2)
- Bioactivity (2)
- Bioceramics (2)
- Flowability (2)
- Glass microspheres (2)
- KNN (2)
- Keramik (2)
- Large animal model (2)
- Large animal model sheep (2)
- Laser (2)
- Layerwise slurry deposition (2)
- Lunar regolith (2)
- Mars (2)
- Mechanical properties (2)
- Osteoporotic vertebral fracture (2)
- Printing (2)
- Scaffold (2)
- Si3N4 (2)
- Silicon carbide (2)
- Silicon nitride (2)
- Space (2)
- Strength (2)
- Vertebroplasty (2)
- 2PP (1)
- 3-D printing (1)
- 3D (1)
- ATZ (1)
- Additive manufacturing, 3D printing (1)
- Al2O3 reaction bonding (1)
- Al2O3-Y2O3-ZrO2 (1)
- Alcium alkali phosphate (1)
- Alkali-activated materials (1)
- Alpha-tricalcium phosphate (1)
- Alumina toughened zirconia (1)
- Anisotropic grain growth (1)
- Bacteria (1)
- Binders/binding (1)
- Bio Ceramic (1)
- Bio Ceramics (1)
- Bio active ceramic (1)
- Bioactive bone grafting material (1)
- Bioactive glass scaffold (1)
- Biphasic calcium phosphate (1)
- Bone marrow extrusion (1)
- Bone marrow-derived mesenchymal stem cell (1)
- Bone tissue engineering (1)
- Brushite-forming calcium phosphate cement (1)
- Calcium alkali orthophosphate (1)
- Calcium alkali orthophosphate materials (1)
- Calcium alkaline orthophosphates (1)
- Calcium alkaline phosphates (1)
- Calcium phosphat cement (1)
- Calcium phosphate cement (1)
- Cell culture media (1)
- Cellular (1)
- Cement injection (1)
- Cement-based materials (1)
- Ceramic nano particles (1)
- Characterisation (1)
- Clay ISRU (1)
- Compressive strength (1)
- Crystallization (1)
- Crystallization behavior (1)
- Cuttlefish (1)
- D. ZrO2 (1)
- Debinding (1)
- Defect detection (1)
- Dense alumina (1)
- Drywood termite (1)
- Efficiency (1)
- Emissivity (1)
- Endothelial progenitor cell (1)
- Environment (1)
- Eutectic ceramics (1)
- Ex vivo (1)
- Fatigue (1)
- Fetal bovine serum (1)
- Firing (1)
- Fungi (1)
- Gas flow assisted powder deposition (1)
- Glass ceramics (1)
- Graded (1)
- Grain boundary (1)
- Hausner ratio (1)
- High- viscosity PMMA cement (1)
- Hot stage microscopy (1)
- Hybrid Manufacturing (1)
- ISRU (1)
- Image-based analysis (1)
- In vivo (1)
- In-situ Process Monitoring (1)
- In-vivo (1)
- Infrared optical properties (1)
- Inkjet (1)
- LAS (1)
- LIBS (1)
- LSD print (1)
- Laser beam melting (1)
- Laser processing (1)
- Laser-induced slip casting (1)
- Laserwise-slurry-deposition (LSD) (1)
- Lattices (1)
- Layer-wise slurry deposition (1)
- Layerwise Slurry Deposition (1)
- MGS-1 regolith simulant (1)
- Mandible (1)
- Manufacturing (1)
- Materials science (1)
- Mean pore diameter (1)
- Melting (1)
- Meta material (1)
- Metallic Glass (1)
- Micro-scale bone scaffolds (1)
- Minimal-invasive (1)
- Mixed Ca-K-Na phosphates (1)
- Moon (1)
- Multiresolution modeling (1)
- Multiscale FEA (1)
- Na and K rhenanites (1)
- Nano-ceramic-additive-manufacturing photoresin (1)
- Nano-powder (1)
- NanoCAM (1)
- Nanopowder (1)
- Networking (1)
- Non-destructive Materials (1)
- Osteogenesis (1)
- Oxide ceramic (1)
- PLGA cement (1)
- PV modules (1)
- Parabolic flight (1)
- Particle size (1)
- Particle size gradation (1)
- Phase diagram (1)
- Phase transformations (1)
- Phototrophs (1)
- Photovoltaic modules (1)
- Plasma imaging (1)
- Plasticity (1)
- Polymer (1)
- Polymeric Materials (1)
- Porcelain (1)
- Porous ceramics (1)
- Powder bed (1)
- Powder bed additive manufacturing (1)
- Powder bed density (1)
- Powder flow (1)
- Powder processing (1)
- Powder rheology (1)
- Powder-based processes (1)
- Preceramic polymer (1)
- Preceramic polymers (1)
- Process (1)
- Process development (1)
- Processing window (1)
- Quality assurance (1)
- Rapid nitridation (1)
- Rapid prototyping (1)
- Reaction Sintering (1)
- Reaction bonding (1)
- Real-time deformation (1)
- Real-time qPCR (1)
- Regolith (1)
- Roughness (1)
- SEM micrography (1)
- Safety (1)
- Sand blasting (1)
- Scaffold geometry (1)
- SchwarzP cells (1)
- Selective laser sintering (1)
- Selective laser sintering (SLS) (1)
- Self-Assembly (1)
- Self-organization (1)
- Shadowgraphy (1)
- Shaping (1)
- Sheep (1)
- Si3N4/SiC porous ceramics (1)
- SiO2 (1)
- Silicate glass-ceramics (1)
- Silicon Carbide (1)
- Silicon release (1)
- Sinus floor augmentation (1)
- Slurry (1)
- Smectite (1)
- Softening temperature (1)
- Solar panels (1)
- Standardisation (1)
- Stressed (1)
- Three-dimensional Bone tissue engineering (1)
- Three-dimensional printing (1)
- Trabecular structures (1)
- Transmittance (1)
- Transparency (1)
- Transparent ceramic (1)
- Tricalcium Phosphate (1)
- Triply Periodical Minimal Surface (1)
- Two-photon polymerization (1)
- Two-photon-polymerization (1)
- Unstressed (1)
- Vertebral (1)
- Viscous sintering (1)
- Void defect (1)
- Wetting (1)
- X-ray refraction (1)
- X-ray tomographic (1)
- Yttria stabilized zirconia (1)
- Zirconia: yttria stabilized (1)
- ZnO (1)
- µ-gravity (1)
- µCT (1)
Organisationseinheit der BAM
- 5 Werkstofftechnik (43)
- 5.4 Multimateriale Fertigungsprozesse (43)
- 8 Zerstörungsfreie Prüfung (6)
- 6 Materialchemie (5)
- 8.5 Röntgenbildgebung (4)
- 4 Material und Umwelt (3)
- 7 Bauwerkssicherheit (3)
- 7.4 Baustofftechnologie (3)
- 4.0 Abteilungsleitung und andere (2)
- 5.1 Mikrostruktur Design und Degradation (2)
Paper des Monats
- ja (3)
In additive manufacturing the powder bed based processes binder jetting and powder bed fusion are increasingly used also for the production of ceramics. Final part properties depend to a high percentage on the powder bed density. Therefore, the aim is to use the best combination of powder deposition method and powder which leads to a high packing of the particles. The influence of flowability, powder properties and deposition process on the powder bed density is discussed and the different deposition processes including slurry-based ones are reviewed.
It turns out that powder bed density reached by slurry-based layer deposition exceeds conventional powder deposition, however, layer drying and depowdering are extra steps or more time-consuming for the slurry route.
Depending on the material properties needed the most suitable process for the part has to be selected.
Frass (fine powdery refuse or fragile perforated wood produced by the activity of boring insects) of larvae of the European house borer (EHB) and of drywood termites was tested as a natural and novel feedstock for 3D-printing of wood-based materials. Small particles produced by the drywood termite Incisitermes marginipennis and the EHB Hylotrupes bajulus during feeding in construction timber, were used. Frass is a powdery material of particularly consistent quality that is essentially biologically processed wood mixed with debris of wood and faeces. The filigree-like particles flow easily permitting the build-up of woodbased structures in a layer wise fashion using the Binder Jetting printing process. The Quality of powders produced by different insect species was compared along with the processing steps and properties of the printed parts. Drywood termite frass with a Hausner Ratio HR = 1.1 with ρBulk = 0.67 g/cm3 and ρTap = 0.74 g/cm3 was perfectly suited to deposition of uniformly packed layers in 3D printing. We suggest that a variety of naturally available feedstocks could be used in environmentally responsible approaches to scientific material sciences/additive manufacturing.
This study suggests a tool for a better control on the sintering/crystallization of 3D-printed bioactive glassceramics bodies. A small cantilever in form of a bar with square cross section attached to a base and inclined 34◦ with the horizon, was used to monitor the viscous flow and sintering/crystallization headway of a glassceramic systems. 3D printing and sintering of bioactive glass-ceramics is of great interest for medical care applications.
Viscous flow ensures sufficient densification of the typically low density printed green bodies, while crystallization prevents the structure from collapsing under the gravitational load. As a model system, a bioactive glass called BP1 (48.4 SiO2, 1 B2O3, 2 P2O5, 36.6 CaO, 6.6 K2O, 5.6 Na2O (mol%)), which has a chemical composition based on that of ICIE16, was employed in this work. In addition, ICIE16 was used as a reference glass. The results show that the suggested design is a very promising tool to track the real-time deformation of 3D printed glass-ceramic specimens and gives a good indication for the onset of crystallization as well.
The flow behavior of powders has an essential role in many industrial processes, including powder bed additive manufacturing. The characterization of the flow behavior is challenging, as different methods are available, and their suitability for an application in additive manufacturing is still controversial. In this study, six standardized methods (measurement of bulk density by ISO 60 and by ASTM B329, angle of repose by ISO 4324, discharge time by ISO 6186 and by ASTM B964-16, and Hausner Ratio by ASTM 7481 – 18), the rotating drum method (by GranuDrum) and powder rheometry (Anton Paar powder cell), were applied to five size fractions of a crushed quartz sand powder and compared. A statistical approach is proposed and discussed to correlate the obtained flowability indexes with the packing density of powder beds deposited layer-by-layer, and these correlations are compared between methods. Overall, the measurement of bulk density by ASTM B329 that showed the best correlation with the powder bed density. Advanced methods such as the rotating drum method and powder rheometry did not demonstrate particularly good correlations, however they provided complementary information which can be useful to assess the dynamic behavior of powders.
Influence of the dispersant on the parts quality in slurry-based binder jetting of SiC ceramics
(2022)
Binder jetting is establishing more and more in the ceramic industry to produce large complex shaped parts. A parameter with a great impact on the quality of the parts is the binder–powder interaction. The use of ceramic slurries as feedstock for this process, such as in the layerwise slurry deposition–print technology, allows a great flexibility in the composition. Such slurries are typically composed of ceramic powder, water, and small amounts of various additives. The understanding of the effect of these components on the printing quality is thus essential for the feedstock development. Four models were developed regarding the impact of additives, such as dispersants on printing. These models were confirmed or rebutted by experiments performed for an SiC slurry system with two different concentrations of a dispersant and a commercial phenolic resin used as a binder. It is shown that for this system the influence of the dispersant on the curing behavior and the clogging of the pores by dispersant can be neglected. The redispersion of the dispersant after the curing of the resin has no or only a minor effect. However, the wetting behavior determined by the surface energies of the system seem to be most crucial. In case the surface energy of the slurry additive is significantly lower than the surface energy of the binder, the strength of the green parts and the printing quality will be low. This was shown by inverse gas chromatography, contact angle measurement, rheological characterization, and mechanical tests with casted samples.
The pore geometry of bone scaffolds has a major impact on their cellular response; for this reason, 3D printing is an attractive technology for bone tissue engineering, as it allows for the full control and design of the porosity. Calcium phosphate materials synthesized from natural sources have recently attracted a certain interest because of their similarity to natural bone, and they were found to show better bioactivity than synthetic compounds. Nevertheless, these materials are very challenging to be processed by 3D printing due to technological issues related to their nanometric size. In this work, bone scaffolds with different pore geometries, with a uniform size or with a size gradient, were fabricated by binder jetting 3D printing using a biphasic calcium phosphate (BCP) nanopowder derived from cuttlebones. To do so, the nanopowder was mixed with a glass-ceramic powder with a larger particle size (45–100 µm) in 1:10 weight proportions. Pure AP40mod scaffolds were also printed. The sintered scaffolds were shown to be composed mainly by hydroxyapatite (HA) and wollastonite, with the amount of HA being larger when the nanopowder was added because BCP transforms into HA during sintering at 1150 ◦C. The addition of bio-derived powder increases the porosity from 60% to 70%, with this indicating that the nanoparticles slow down the glass-ceramic densification. Human mesenchymal stem cells were seeded on the scaffolds to test the bioactivity in vitro. The cells’ number and metabolic activity were analyzed after 3, 5 and 10 days of culturing.
The cellular behavior was found to be very similar for samples with different pore geometries and compositions. However, while the cell number was constantly increasing, the metabolic activity on the scaffolds with gradient pores and cuttlebone-derived powder decreased over time, which might be a sign of cell differentiation. Generally, all scaffolds promoted fast cell adhesion and proliferation, which were found to penetrate and colonize the 3D porous structure.
Porous Si3N4 ceramics were prepared via partial nitridation and self-propagating high temperature synthesis (SHS) process. Raw Si and additive Y2O3 were mixed and molded under 10 MPa into a compact, the compact was partial nitridation at 1300 °C to form a porous Si/Si3N4, and then it was buried in a Si/Si3N4 bed for SHS to obtain porous Si3N4 with rod-like β-Si3N4 morphology. The processing combined the advantages of the nitridation of Si and SHS with low cost, low shrinkage and time saving. Porous Si3N4 with a porosity of 47%, a strength of 143 MPa were obtained by this method.
Tapes, cast by blade deposition of a lithium aluminosilicate glass slurry, were sintered using a YAG-fiber laser, with the aim of finding suitable parameters for an additive manufacturing process based on layer-wise slurry deposition and selective laser densification. The influence of the laser parameters (output power and scan velocity) on the sintering was evaluated, by scanning electron microscopy and by X-ray diffraction, on the basis of the quality of the processed layer. Well densified samples could be obtained only in a small window of values for the output power and the scan velocity. The measurement of the width of a set of single scanned lines allowed also to estimate the minimum resolution of the system along the layer plane.
The production of agglomerate-free SiO2 particles exhibiting a monomodal distribution of particle sizes of around 300 nm by means of direct laser fuming of micrometric SiO2 powders has been successfully demonstrated. With a 12 kW cw CO2 laser system, a production rate of up to 1 kilogram powder per hour was achieved. Almost ideal spherical amorphous SiO2 particles in a broad particle size distribution between 10 nm and several 100 nm (d50 ≈ 300 nm) were synthesized. Several observations suggest weak agglomeration forces between the particles. A temperature reduction of 200 °C for sintering powder compacts was observed.