Filtern
Erscheinungsjahr
- 2011 (4) (entfernen)
Dokumenttyp
Sprache
- Englisch (4)
Referierte Publikation
- nein (4)
Schlagworte
- Co-firing (2)
- Ferrite (2)
- LTCC (2)
- Aggregation (1)
- Azoverbindungen (1)
- Calcium peroxide (1)
- Constrained sintering (1)
- EOS (1)
- Grenzflächenreaktion (1)
- IGUS (1)
- Keramische Multilayer (1)
- Nanostrukturen (1)
- Photochromie (1)
- Polymere (1)
- Round robin (1)
- Shrinkage behavior (1)
- Sodium nitrate (1)
- Sodium perborate monohydrate (1)
- Solid oxidizer test (1)
- United Nations (1)
The classification of solid oxidizers according to the regulations on the transport of dangerous goods (based on the UN Recommendations/Model Regulations and accepted by all international organisations for the transport of dangerous goods as ADR, IMO, IATA) and in future also according to the GHS (Globally Harmonized System of Classification and Labelling of Chemicals) is performed on the basis of the results of the UN test O.1 (UN test O.1 ―Test for oxidizing solids‖ described in chapter 34.4.1 in the Recommendations on the Transport of Dangerous Goods – Manual of Tests and Criteria, see [1]). This test was introduced into the UN Manual of Tests and Criteria in 1995 as a replacement for a similar test from 1986. Even if the UN O.1 test as described in the current 5th revised edition of UN Manual of Tests and Criteria gives some improvements compared to the old test, which had had many deficiencies, there are still some problems left with this test in terms of e.g. repeatability or reproducibility of test results, how to handle compacted or multilayer formulations like tablets, toxicity and partly significantly varying particle size distribution within defined fractions of 150 μm to 300 μm of the reference oxidizer potassium bromate (KBrO3). For this reason the IGUS EOS working group installed an ad-hoc working group in 2002 assigned with the task to propose solutions for the existing problems. The appropriateness of such proposed solutions has to be proved by the method of interlaboratory (round robin) tests before they are presented for the adoption to the UN Committee of Experts on the TDG and on the GHS with a proposal of a completely revised test procedure.
Integration of magnetic functional components in LTCC Circuit boards calls for co-firing of dielectric and ferrite tapes. Ni-Cu-Zn ferrites with permeability of p=900 were developed which can be fully densified at the Standard LTCC sintering temperature of 900 °C. Successful co-firing of this ferrite with dielectric tapes requires the adaptation of the shrinkage behavior of the materials as well as the thermal expansion during the cooling period - especially in the temperature range below the transformation point of the glassy phase of the dielectric tape. To match these preconditions, a new dielectric LTCC material with steep sintering curve and high thermal expansion coefficient was designed. Sintered multilayer composed of Ni-Cu-Zn ferrite and tailored dielectric tapes are free of cracks and possess no open porosity. No significant interdiffusion between the ferrite and dielectric tapes was found by EDX measurements. Compared to pure ferrite laminates the permeability of co-sintered Ni-Cu-Zn ferrite layers is drastically reduced to 400, i.e. a decrease of more than 50 %.
To investigate the origin of this permeability reduction, Ni-Cu-Zn ferrite laminates were sintered separately, and in combination with alumina release tapes or dielectric tapes, respectively. SEM and EDX analysis of co-fired laminates reveal differences in the ferrite grain growth behavior. Ferrite laminates with homogeneous microstructure and grain size up to 50 pm exhibit large permeability. However, growth of ferrite grains does not take place near the interface between ferrite and release or dielectric tapes. There is a strong correlation between high permeability and volume fraction of large ferrite grains. Regions of fine and coarse grains inside the ferrite layers show different bismuth concentration; the Bi-content is larger in regions of fine ferrite grains.
Further miniaturization of electronic packaging calls for integration of magnetic functional components into LTCC modules. For integration of magnetic function into LTCC, low fired MnZn- and NiCuZn-ferrites which can be fully densified at the standard LTCC sintering temperature of 900°C were developed. To co-fire these ferrite tapes with dielectric tapes the sintering shrinkage and the coefficient of thermal expansion of ferrite and dielectric tapes must be matched. For each ferrite material a new LTCC dielectric material was designed. The embedded ferrite tapes into new LTCC dielectric tapes can be sufficiently densified during co-firing at 900°C without any cracking. Compared to separately sintered ferrites the permeability of embedded ferrite tapes is reduced. For embedded NiCuZn ferrites permeabilities between 230 and 570 (at 2 MHz) according to the thickness of the embedded ferrite layer were measured. For embedded MnZn ferrites a permeability of 300 was measured.
Synthetic molecular systems undergoing structure and property changes as a response to external stimuli offer a series of relevant functions. Their direct use in solution, immobilized at surfaces, or integrated into adequate matrices, allow for the elaboration of nano-carriers, molecular electronic memory circuits, adaptive systems, artificial muscles, or healable materials, among others. Reversible systems are commonly generated by utilizing molecular switches as responsive bi-stable molecules. Of particular interest are switches controlled by non-invasive triggers, especially light, which can display high spatial and temporal resolution. Photoswitches were used to change properties, such as conductance and basicity, based on light-induced alteration of the molecular geometry, that is, their dimensions and shape. In nature, light-induced geometrical modifications of molecular systems lead to primary biological functions, such as the visual perception in vertebrates, or proton pumping in some bacteria, two examples that nicely illustrate the potential of photo-inducing structural modifications in organic systems.