Filtern
Dokumenttyp
Referierte Publikation
- nein (8) (entfernen)
Schlagworte
Organisationseinheit der BAM
Paper des Monats
- ja (1)
Titanium and its alloys are known to allow the straightforward laser-based manufacturing of ordered surface nanostructures, so-called high spatial frequency laser-induced periodic surface structures (HSFL). These structures exhibit sub-100 nm spatial periods – far below the optical diffraction limit. The resulting surface functionalities are usually enabled by both, topographic and chemical alterations of the nanostructured surfaces. For exploring these effects, multi-method characterizations were performed here for HSFL processed on Ti–6Al–4V alloy upon irradiation with near-infrared ps-laser pulses (1030 nm, ≈1 ps pulse duration, 1–400 kHz) under different laser scan processing conditions, i.e., by systematically varying the pulse repetition frequency and the number of laser irradiation passes. The sample characterization involved morphological and topographical investigations by scanning electron microscopy (SEM), atomic force microscopy (AFM), tactile stylus profilometry, as well as near-surface chemical analyses hard X-ray photoelectron spectroscopy (HAXPES) and depth-profiling time-of-flight secondary ion mass spectrometry (ToF-SIMS). This provides a quantification of the laser ablation depth, the geometrical HSFL characteristics and enables new insights into the depth extent and the nature of the non-ablative laser-induced near-surface oxidation accompanying these nanostructures. This allows to answer the questions how the processing of HSFL can be industrially scaled up, and whether the latter is limited by heat-accumulation effects.
Femtosecond laser pulses are close to industrial use. The advantages of ultrashort laser pulses for micromachining applications especially in the case of dielectric and biological samples down to pulse durations of 5 fs have been established. The current international standards of laser safety are primarily concerned with CW and pulsed lasers down to the nanosecond range. Therefore, human tissue and laser-protection equipment was investigated with respect to its resistance and protection performance for femtosecond laser illumination down to 30 fs. This included filter glasses for laser protection eyewear, polymer and textile materials used in curtains and guards. Bulk absorber filters can provide enough protection against laser radiation, give a sufficiently broad absorption spectrum. Materials are damaged more easily by femtosecond laser radiation. The need for sufficient spectral broadness as well as the different damage thresholds have to be included in international laser safety standards. This work should trigger the development of novel eye-protection devices that are lighter and ergonomically more acceptable than present commercial models.
Single-pulse damage thresholds of hydrogenated amorphous carbon (a-C:H) films were measured for 8-ns laser pulses at 532-nm wavelength. Layer thicknesses from below the optical penetration depth to above the thermal diffusion length (60 nm13 µm) were examined. After correction of the damage-threshold values for the fraction of energy effectively absorbed by the material, the damage threshold was found to increase linearly with the layer thickness, also for film thicknesses below the optical penetration depth of a-C:H. The threshold fluence reached the bulk value for a layer thickness equal to the thermal diffusion length. The thermal diffusion coefficient was obtained from fitting the experimental data. Several phenomena like graphitization, blistering, exfoliation, and ablation were observed for different fluence regimes and film thicknesses.
In this paper, safety-related experiments with ultra-short laser pulses (down to 30 fs) on various components
(goggles, curtains) for laser protection are presented. The damage and failure behaviour of
protective devices has been investigated dependent on practical conditions such as pulse duration, laser
.uence, pulse number, and repetition rate.
The e.ects of laser-irradiation on materials can be roughly divided into transient ones like laserinduced
transmission (LIT) or short-lived colour centres and permanent damages like the stable colour
centres and ablation. The former e.ects are particularly important for transparent devices like laser
goggles.
To obtain a complete overview on laser safety issues and the prevention of failure there are two
important .elds of investigation:
1. the e.ects of laser radiation on human eyes and skin, and
2. on the possible protection materials.
Both .elds have been addressed during the recently .nished German project SAFEST (safety aspects
in femtosecond technology). The amount of safety data available in the ultrashort pulse region has
been increased remarkably. This allows for a re-evaluation of known laser protection materials for this
region of pulse durations and for the evaluation of new designs that promise high protection levels
while being light-weight and convenient to use.