Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (27) (entfernen)
Schlagworte
Organisationseinheit der BAM
- 4 Material und Umwelt (10)
- 4.1 Biologische Materialschädigung und Referenzorganismen (8)
- 4.0 Abteilungsleitung und andere (2)
- 4.3 Schadstofftransfer und Umwelttechnologien (2)
- 1 Analytische Chemie; Referenzmaterialien (1)
- 1.8 Umweltanalytik (1)
- 3 Gefahrgutumschließungen; Energiespeicher (1)
- 3.1 Sicherheit von Gefahrgutverpackungen und Batterien (1)
- 5 Werkstofftechnik (1)
- 5.1 Mikrostruktur Design und Degradation (1)
Unterschiedliche Befeuchtungssysteme für Vitrinen, die die Ausstellungsobjekte bei definierter Luftfeuchtigkeit vor externen Einflüssen wie Staub bewahren sollen, wurden im Hinblick auf die Möglichkeit der potenziellen mikrobiologischen Kontamination untersucht. Ergänzend hierzu wurden Parameter wie pH-Wert und Leitfähigkeit des Wassers im Befeuchter untersucht und die mikrobiellen flüchtigen organischen Verbindungen (MVOC, microbial volatile organic compounds) in der Modellvitrine bestimmt. Die Leitfähigkeitsmessung kann als Indikator für den Verunreinigungsgrad des Wassers dienen, weil sie mit der mikrobiologischen Belastung korreliert. Weiterhin war eine mikrobiologische Belastung der Luft in der Modellvitrine auch bei relativ hoher Verunreinigung des Befeuchtungswassers nicht nachzuweisen.
The potential release of hazardous substances from polymer-based products is currently in the focus of environmental policy. Environmental simulations are applied to expose such products to selected aging conditions and to investigate release processes. Commonly applied aging exposure types such as solar and UV radiation in combination with water contact, corrosive gases, and soil contact as well as expected general effects on polymers and additional ingredients of polymer-based products are described. The release of substances is based on mass-transfer processes to the material surfaces. Experimental approaches to investigate transport processes that are caused by water contact are presented. For tailoring the tests, relevant aging exposure types and release quantification methods must be combined appropriately. Several studies on the release of hazardous substances such as metals, polyaromatic hydrocarbons, flame retardants, antioxidants, and carbon nanotubes from polymers are summarized exemplarily. Differences between natural and artificial exposure tests are discussed and demonstrated for the release of flame retardants from several polymers and for biocides from paints. Requirements and limitations to apply results from short-term artificial environmental exposure tests to predict long-term environmental behavior of polymers are presented.
Ursachen und Auswirkungen von Schimmel an zentralasiatischen Wandmalereien aus dem 5./6. Jh. n. Chr.
(2011)
Bereits bei der Entdeckung der zentralasiatischen Kultstätten gegen Ende des 19. Jh. durch zahlreiche Expeditionen waren Beschädigungen durch Schimmelpilze in situ festgestellt worden. Die von den deutschen Expeditionen in Zentralasien Vorgefundenen Kultstätten hatten unterschiedliche Erhaltungszustände.
Einige Höhlen waren komplett eingestürzt, verschüttet und mußten freigelegt werden. Bei anderen Höhlen waren die Vorhallen zerstört und es tropfte Wasser aus Deckenausbrüchen und Rissen im Felsgestein. Albert Grünwedel dokumentiert in seinem Buch „Kultstätten" auf S. 148 die Auffindung der sog. Malerhöhle (Höhle Nr. 17) und schreibt hierzu: „Diese alte und schöne Höhle war völlig durch eine Schlammrunse verschlossen und unsichtbar...
Als sie entdeckt wurde, waren die Wände dick mit Schimmel belegt. Da zu befürchten war, daß die Bilder abfallen würden, wurde nur eine kleine Öffnung gemacht, um der Luft Zutritt zu gewähren, da auch der Aufenthalt in der Höhle infolge des Geruchs der Pilze unmöglich war. Diese Öffnung wurde allmählich erweitert und als der Schimmelbeschlag getrocknet war, wurden die Wände mit chinesischem Branntwein gewaschen.
Dadurch fiel der aufgetrocknete Schimmel ab und es wurde möglich, sich in der Höhle aufzuhalten."
ABSTRACT: A collection of thioimidazolium salts were synthesized and used as a new class of nonvolatile alkylating agents. Their nonvolatility prevents exposure during use or handling and are thus drastically safer than conventional alkylating agents. We discovered that thioimidazolium Iodide salts cannot release volatile compounds in the solid state, but instead only decompose when molten. Since decomposition proceeds via alkyl iodide elimination, SN2 of iodide on the thioimidazolium cation is constrained in the solid state, and instead can occur only upon melting when ions are mobile. By smart design of these alkylators, the melting point and thus the decomposition temperature of these salts can be increased from 106 to 169 °C and release negligible volatile organic compounds prior to melting. Thioimidazolium-bis(trifluoromethanesulfonyl)imide (TFSI) ionic liquids act as a completely nonvolatile and air-stable TFSI-based alkylating agent and can be used for high-throughput Synthesis of TFSI ionic liquids without solvent. Alkyl groups from methyl to dodecyl can be transferred to a nucleophile and the product purified by sublimation of the thione byproduct, which can then be recycled. We also found that thioimidazolium salts with a dodecyl chain are bactericidal, yet can hydrolyze in water to form benign neutral products, and thus wont accumulate in the environment. These results demonstrate that thioimidazolium salts are a designable platform for the pursuit of safer and more environmentally friendly alkylating and antiseptic agents.
The biodeterioration of water-based manufactured formulations, such as polymer dispersions, is a major problem for the producing companies and the users of such products. Industrial preservatives, also known as biocides, are therefore used to protect these and similar products from the effects of microorganisms, predominantly bacteria and yeasts. In the absence of internationally recognised standard methods for determining the resistance of polymer dispersions to microbial growth and the efficacy of biocides used in them, protocols for testing other products, e.g., paints, have been adapted, and other methods produced by manufacturing companies, test laboratories, and academic institutions have been used. Often these do not take into account the specific nature of the materials being tested, the types of organism commonly causing contamination, and the conditions that the polymer dispersions will be exposed to during manufacture, storage, and use. By conducting a series of round-robin, collaborative tests, the member organisations of the International Biodeterioration Research Group Polymer Dispersion Working Group have identified the bacteria that commonly infect polymer dispersions, defined the main parameters necessary for a standard method of test, and developed a protocol that is robust, repeatable, and reproducible. The recommended test involves three repeat inoculations of the material with a previously determined mix of seven Gram-negative bacteria and evaluation of living cells by a simple plating technique. The work reported here, carried out by nine participating laboratories, is a final statistical validation and suggests that the method is eminently suitable as a standard test method.
Trichothecene mycotoxins, with T-2 and HT-2 toxins being the main representatives of the type A subgroup, are naturally and worldwide occurring contaminants frequently found in grain-based food and feed. Due to the high consumption of these products and the potential health risk associated herewith, concerns about the safety and quality of food and feed have increased over the last decades at both governmental and consumer levels. Since it is not possible to avoid their occurrence, tremendous efforts have been performed to identify and monitor mycotoxins in food and feed to make their consumption safe. However, suitable certified reference materials (CRMs) intended for quality assurance and quality control purposes are still lacking for many mycotoxin-matrix combinations. Therefore, in the framework of a European Reference Material (ERM®) project, the first CRM for T-2 and HT-2 toxin in ground oat flakes (ERM®-BC720) was developed according to the requirements of ISO Guide 35. The whole process of ERM®-BC720 development, including sample preparation, homogeneity and stability studies and value assignment, is presented. The assignment of the certified mass fractions was based upon an in-house study using high-performance liquid chromatography isotope-dilution tandem mass spectrometry. Simultaneously, an interlaboratory comparison study involving 24 expert laboratories was conducted in order to support the in-house certification study. The certified values and their corresponding expanded uncertainties (k=2) for both T-2 and HT-2 toxin in ERM®-BC720, traceable to the international system of units, are (82±4) µg kg-1 and (81±4) µg kg-1, respectively.
The antileaching efficacy of sol-gel-derived TiO2- and SiO2-based precursors has been evaluated through laboratory leaching trials with pine sapwood in two different ways. In a one-step process, wood was vacuum impregnated by the precursor solutions containing CuCl2. The copper (Cu) emission rates of the sol-gel-based impregnated woods were up to 70% lower than that of wood treated with pure CuCl2 solution at the same level of concentration. More improvement (80%) could be achieved in a two-step process, in which sol-gel precursors were introduced into an already CuCl2-treated wood. The refinement was attributed to several effects. In the one-step approach, Cu was embedded in the TiO2/SiO2 gels formed in the wood texture. During a two-step impregnation, gel layers that were formed in the wooden interior acted as an effective diffusion barrier. The sol-gel impregnations made wood more hydrophobic; therefore, the low amount of water that penetrated the cell wall was less efficient to leach out Cu.
Wood treated with nano metal fluorides is found to resist fungal decay. Sol−gel synthesis was used to synthesize MgF2 and CaF2 nanoparticles. Electron microscopy images confirmed the localization of MgF2 and CaF2 nanoparticles in wood. Efficacy of nano metal fluoride-treated wood was tested against brown-rot fungi Coniophora puteana and Rhodonia placenta. Untreated wood specimens had higher
mass losses (∼30%) compared to treated specimens, which had average mass loss of 2% against C. puteana and 14% against R. placenta, respectively. Nano metal fluorides provide a viable alternative to current wood preservatives.
As the results of a 14 weeks outdoor exposure of a series of automotive coatings in South Florida, the panels were found to be overgrown with an almost closed layer of mildew. Pinholes remained as permanent surface damage after removing the mildew mycelium. The extent of the damage differed in dependence of the kind of the coating. By tracing the images and profiles of the coating surfaces systematically over all phases of weathering and the subsequent cleaning procedure, a connection between formation of pinholes and mildew growth could be found. Outdoor weathering tests in other regions of Florida as well as in Europe and Australia showed that pinholes caused by mildew attack could also be found in all other locations, but always to a lower extent than in South Florida. The standardised mildew tests EN ISO 846 and MIL-STD 810F for laboratory exposure failed to reproduce the formation of pinholes.
Material performance testing of wood-plastic composites (WPC) requires adequate and time-efficient evaluation of the resistance against fungal colonisation and decay. This study investigates the effects of weathering on WPCs and subsequent material degradation by fungi. Weathering using UV radiation, water spray and repeated frost incidents caused micro- and macro-cracks. Fourier transform infrared spectroscopy (FTIR) demonstrated delignification of wood particles at the weathered WPC surface. Despite of increased surface area, accessibility for fungal hyphae and moisture content, weathering enhanced mass loss due to fungal decay only subtly but not significantly. These potentially enhancing effects for fungal decay are assumed to be outbalanced by delignification due to photo-oxidation and leaching of degradation products resulting in loss of nutrient sources essential for fungal growth.
Flame retarded wood-plastic composites (WPCs) should allow safe application in areas of fire risk. Halogen-free flame retardants can contain high amounts of nitrogen, phosphorus or sulphur, which may serve as nutrition source for wood degrading fungi and accelerate wood decay. Therefore, the material resistance of WPCs with each of four flame retardants against both fire or fungal decay was examined in comparison to WPC without flame retardant. Expandable graphite showed the best performance against fire in cone calorimetry and radiant panel testing. Two ammonium polyphosphates and a third nitrogen-containing flame retardant were not as effective. Contrary to the possibility that flame retardants might enhance fungal decay of WPC, the opposite effect occurred in case of the wood-degrading fungi Trametes versicolor and Coniophora puteana according to determination of mass loss and decrease of bending modulus of elasticity. Only the surface mould Alternaria alternata slightly increased the degradation of WPCs with nitrogen-containing flame retardants compared to WPC without flame retardant according to mass loss data and FTIR-ATR analyses. Finally, WPC including expandable graphite as flame retardant was effective against both fire and fungal decay.
The metabolism of moulds results in the formation of various microbial volatile organic compounds (MVOCs). These substances can be used as an indicator for the presence of moulds in the indoor environment. Three different mould strains were cultivated on culture media and IMS spectra of gaseous mould metabolites were recorded using a portable mini system with a tritium source and a 5 cm drift cell. The headspace spectra are characteristic for mould species and their age. Typical gaseous components of the metabolites were identified and compared with results obtained from gas chromatography using a mass spectrometer detector. It was observed that the MVOCs formation depends on mould species and their growing stage with a maximum of MVOCs emission occurring during the first 10 days. These preliminary results show that IMS can be applied to detect MVOCs in indoor environment and indicate hidden mould growth.
Improved Durability of Wood Treated with Nano Metal Fluorides against Brown-Rot and White-Rot Fungi
(2022)
Low-water soluble metal fluorides such as magnesium fluoride (MgF2) and calcium Fluoride (CaF2) were evaluated for decay protection of wood. Initially, the biocidal efficacy of nano metal fluorides (NMFs) against wood destroying fungi was assessed with an in-vitro agar test. The results from the test showed that agar medium containing MgF2 and CaF2 was more efficient in preventing fungal decay than stand-alone MgF2 or CaF2. These metal fluorides, in their nanoscopic form synthesized using fluorolytic sol-gel synthesis, were introduced into the sapwood of Scots pine and beech wood and then subjected to accelerated ageing by leaching (EN 84). MAS 19F NMR and X-ray micro CT images showed that metal fluorides were present in treated wood, unleached and leached. Decay resistance of Scots pine and beech wood treated with NMFs was tested against Wood destroying fungi Rhodonia placenta and Trametes versicolor in accordance with EN 113. Results revealed that mass losses were reduced to below 3% in wood treated with the combination of MgF2 and CaF2.
It is concluded that NMFs provide full protection to wood even after it has been leached and can be used as wood preservatives in outdoor environments.
Materials that confer antimicrobial activity, be that by innate property, leaching of biocides or design features (e.g., non-adhesive materials) continue to gain popularity to combat the increasing and varied threats from microorganisms, e.g., replacing inert surfaces in hospitals with copper. To understand how efficacious these materials are at controlling microorganisms, data is usually collected via a standardised test method. However, standardised test methods vary, and often the characteristics and methodological choices can make it difficult to infer that any perceived antimicrobial activity demonstrated in the laboratory can be confidently assumed to an end-use setting. This review provides a critical analysis of standardised methodology used in academia and industry, and demonstrates how many key methodological choices (e.g., temperature, humidity/moisture, airflow, surface topography) may impact efficacy assessment, highlighting the need to carefully consider intended antimicrobial end-use of any product.
Test methods for efficacy assessment of antimicrobial coatings are not modelled on a hospital environment, and instead use high humidity (>90%) high temperature (37 ◦C), and no airflow. Therefore, an inoculum will not dry, resulting in an antimicrobial surface exhibiting prolonged antimicrobial activity, as moisture is critical to activity. Liquids will dry quicker in a hospital ward, resulting in a reduced antimicrobial efficacy compared to the existing test, rendering the test results artificially favourable to the antimicrobial claim of the product. This study aimed to assess how hospital room environmental conditions can affect the drying time of an inoculum, and to use this data to inform test parameters for antimicrobial efficacy testing based on the hospital ward. The drying time of different droplet sizes, in a range of environmental conditions likely found in a hospital ward, were recorded (n = 630), and used to create a model to inform users of the experimental conditions required to provide a drying time similar to what can be expected in the hospital
ward. Drying time data demonstrated significant (p < 0.05) variance when humidity, temperature, and airflow were assessed. A mathematical model was created to select environmental conditions for in vitro antimicrobial efficacy testing. Drying time in different environmental conditions demonstrates that experimental set-ups affect the amount of time an inoculum stays wet, which in turn may affect the efficacy of an antimicrobial surface. This should be an important consideration for hospitals and other potential users, whilst future tests predict efficacy in the intended end-use environment.
During their growth on wood many fungi produce characteristic volatile organic compounds as secondary metabolites. These microbial volatile organic compounds (MVOCs) can be used as indicators of fungal growth even when such growth is concealed. In order to investigate the formation of these volatile metabolites on building materials, specimens of pine sapwood on agar media colonized by the dry-rot fungus Serpula lacrymans and a mixture of six moulds were examined. MVOCs from this fungal growth were studied over a period of up to half a year by ion mobility spectrometry (IMS) headspace analysis using a sensitive, portable IMS mini-device. The IMS headspace spectra from the growing fungal specimens obtained during this time span are differed from non-incubated wood specimens and indicate the presence of a mixture of MVOCs. The composition and amount of volatile metabolites of the fungi changed during cultivation. This was confirmed by a principal component analysis (PCA). Identification of different MVOCs in the headspace according to drift time and the mobility of ionized gaseous species in reference to GC-MS investigations were proposed. It was concluded that IMS can be used as a rapid and sensitive on-site method to indicate actively growing fungi concealed within wood.