Filtern
Dokumenttyp
- Beitrag zu einem Tagungsband (17)
- Sonstiges (1)
Sprache
- Englisch (10)
- Deutsch (7)
- Mehrsprachig (1)
Referierte Publikation
- nein (18) (entfernen)
Schlagworte
- Damping concrete (4)
- Dehnratenabhängigkeit (3)
- Materialmodellierung (3)
- Drop test (2)
- Dynamic (2)
- Dämpferbeton (2)
- Material models (2)
- Penetration (2)
- Polyurethan Schaum (2)
- Polyurethane foam (2)
In Germany dual purpose casks for spent nuclear fuel (SF) or high level radioactive waste (HLW) are used for safe transportation and interim storage. Key safety issues in both fields are the safe enclosure of the radioactive material, the safe removal of decay heat, securing nuclear criticality safety, limitation of radiation exposure to acceptable levels and keeping it as low as reasonable achievable (ALARA principle).
Whereas these safety requirements during transportation are ensured by the Type-B(U)-design testing and approval procedure on basis of internationally agreed IAEA (International Atomic Energy Agency) requirements storage licenses are issued on national and site specific safety analyses.
This paper presents experiences from recent interim storage safety evaluation and licensing procedures in Germany on basis of a Type-B(U) certified cask designs concerning specific differences from Operation and accident conditions inside the storage facility. The focus is laid on the interaction of cask and building structures with regard to shielding, heat removal and accident analyses including aircraft crash. Basic safety is assured by thick-walled metal casks with monitored double lid Systems. They also reduce radiation to levels where workers can safely operate and maintain the casks inside the storage facility. The storage building e. g. provides additional shielding and protection against extemal hazards depending on the building construction. In addition, the storage building helps to reduce radiation levels at the boundary of the storage site well below regulatory limits given by the German Radiation Protection Ordinance (StrSchV).
Abfallgebinde, die im Endlager Konrad eingelagert werden sollen, müssen die Anforderungen und Kriterien erfüllen, die in den Endlagerungsbedingungen (SE-IB-29/08-Rev-1 [1]) und in der Produktkontrolle (SE-IB-30/08-Rev-1) festgelegt sind. Die Qualifizierung der Abfallbehälter erfolgt auf dieser Grundlage in Form von Bauartprüfungen, die von der Bundesanstalt für Materialforschung und -prüfung (BAM) im Auftrag des Bundesamtes für Strahlenschutz (BfS) durchgeführt werden. Darüber hinaus sind die im Hinblick auf Behälterbauartprüfungen relevanten Nebenbestimmungen aus dem Planfeststellungsbeschluss für das Endlager Konrad zu berücksichtigen. Zur besseren Anwendbarkeit werden diese Nebenbestimmungen in die Endlagerungsbedingungen und die Produktkontrolle eingearbeitet. Begleitend ist als Hilfestellung für die Abfallablieferer und Behälterhersteller ein Leitfaden geplant, der praktikable Nachweisstrategien aufzeigt und, soweit erforderlich, Hintergrundinformationen zu den Spezifikationen der Regelwerke liefert. Die BAM ist vom BfS beauftragt, hierfür Vorschläge zu entwickeln und Empfehlungen abzugeben.
Im Zuge des Forschungsvorhabens ENREA (Entwicklung rechnerischer Analysemethoden für stoßdämpfende Strukturen beim Anprall oder Absturz von Abfallgebinden) führt die BAM systematische Untersuchungen an stoßdämpfenden Werkstoffen, unter anderem an Fichtenholz, durch. Zweck der mit diesen Untersuchungen erzeugten Datenbasis ist die Erstellung und Parametrierung eines Finite-Elemente- (FE-) Materialmodells, das die Modellierung holzgefüllter stoßdämpfender Bauteile von Transportbehältern für radioaktive Stoffe in der FE-Simulation ermöglichen soll.
Anhand von Ergebnissen aus der ersten Versuchsphase werden der Einfluss der Dehnrate und der Faserorientierung auf das Kraft-Verformungs-Verhalten von Fichtenholz diskutiert. Anschließend wird die rechnerische Modellierung von Fichtenholz diskutiert und die Anforderungen an ein Materialmodell werden erläutert.
Elastomer seals are widely used as barrier seals in containers for low and intermediate level radioactive waste and in some countries for spent fuel transportation casks. Depending on the area of use, the rubber materials have to demonstrate proper sealing performance with regard to mechanical, thermal and environmental conditions as well as irradiation during the entire operation period.
In Germany the low and intermediate level radioactive waste is planned to be disposed in the Konrad repository in standardized containers. Many of these containers use an elastomer seal between lid and container body. Depending on the radiactive inventory and a possible containment of the waste in inner barrels and/or concrete structures, such containers may require a specific leak tightness. In such cases, specified leakage rates are shall not be exceeded by the the seals to keep potential activity releases from the inventories well below defined limits.
Generally, all waste containers have to fulfill the waste acceptance criteria for the Konrad repository as defined by the reports BfS SE-IB-29/08 and SE-IB-30/08. From these criteria several requirements for seal performance are derived. The seals have to:
- ensure full functionality until final container disposal,
- maintain its function in case of a thermal or mechanical accident,
- ensure encapsulation also at -20 °C.
This combination of requirements is challenging especially as a seal exchange, which is typical for many other applications, is hardly possible and thus a sound understanding of how to perform safety evaluation of containers is required. Therefore BAM has initiated investigations on elastomer seal behaviour. This work focuses on low temperature behaviour and sealing performance concerning static conditions as well as partial loss of compression and ageing of elastomer seals. Concerning ageing, property changes caused by long-term thermooxidative conditions as well as gamma irradiation are investigated.
This contribution presents an overview and explanation of the aims of the ongoing research and gives an update of the most relevant results.
Während des Transportes sind Behälter für hoch radioaktive Abfälle durch stoßdämpfende Bauteile vor Einwirkungen, die aus Unfallszenarien gemäß den IAEA Regularien resultieren können, weitestgehend geschützt. Nach dem Entfernen dieser Komponenten im Rahmen der Einlagerung ins Zwischenlager müssen Vorkehrungen getroffen sein, um Beanspruchungen der Behälter aus möglichen Handhabungsunfällen im Empfangsbereich zu reduzieren. Die Maßnahmen müssen vor allem darauf abzielen, die stoßdämpfenden Eigenschaften der potentiellen Aufprallflächen zu optimieren. Da Standardmaterialien für Fundamente nur ein geringes Energieabsorptionsvermögen aufweisen, wurde durch die Firma HOCHTIEF eine neuartige Betonmixtur entwickelt, bei der ein spezieller Leichtzuschlag zum Einsatz kommen. Zur Charakterisierung dieses sogenannten Dämpferbetons liegen Standardkennwerte vor sowie Messwerte aus Eindringversuchen, die zur Qualitätssicherung für jede Produktcharge durchgeführt werden. Das stoßdämpfende Potential des neuen Werkstoffs kann jedoch nur dann vollkommen ausgeschöpft werden, wenn die Energieabsorption in numerischen Simulationen der Behälterabstürze über die gesamte Belastungsdauer zuverlässig wiedergegeben wird. Für die Implementierung und Anpassung eines entsprechenden Materialmodelis in einem Finite Elemente (FE) Programm
sind Daten aus systematischen Druckversuchen mit Variation der relevanten Einflussgrößen erforderlich. An der BAM werden daher im Rahmen eines werkstoffübergreifenden Forschungsvorhabens zur Untersuchung von stoßdämpfenden Strukturen auch die Eigenschaften von Dämpferbeton experimentell untersucht und zugehörige numerische Methoden entwickelt. Der aktuelle Beitrag behandelt die Ergebnisse der ersten Projektphase, in der kubische Probekörper mit der Kantenlänge 100mm bei unterschiedlichen Lagerungsbedingungen statisch und dynamisch gestaucht wurden. In nachfolgenden Versuchen wird der Einfluß der Probengröße ermittelt sowie die Eignung der verwendeten Materialmodelle anhand realistischer Belastungssituationen validiert.
Versuchsprogramm.
In drop test scenarios related to assessing and licensing the storage procedure of spent fuel and high active waste, the casks under examination are generally not equipped with impact limiters. Hence, the extent of mechanical stresses in case of an assumed handling accident is largely affected by the ground properties of the reception hall floor in the specific storage facility.
Unlike conventional brittle foundation materials, damping concrete performs quite well in such applications as it features high stiffness as well as high energy absorption due to the filler pore volume. However, its damping ability is not sufficiently exploited in current finite element (FE) calculations due to a lack of advanced material models for simulating its impact response. An implementation of qualified concepts that account for plastic, strain rate dependent behavior requires additional information that has to be provided by systematic test series.
BAM recently started a research project to generate such data, subsequently to develop and to improve numerical methods for the analysis of impact limiters and damping foundation material and thus to optimize safety assessment tools for the design of transport and storage casks. A major part of this research concerns dynamic compression tests of variably shaped specimens conducted at a servo hydraulic 1MN impact testing machine as well as at a BAM facility for guided drop tests. This presentation focuses 100mm damping concrete cubes deformed vertically at constant rates under different constraint conditions. For example, a special fitting jig was constructed to subject the specimens to multi-axial loading. Thereby a deformation of 60% could be applied.
Simulation was conducted by FE code ABAQUS based on material models Concrete damaged plasticity and Crushable foam which both allow defining rate sensitive nonlinear stress-strain relations in compression beyond the classic metal plasticity approach.
Transport and storage casks for medium and high level radioactive waste are subjected to extreme heavy loads during the accidental drop scenarios prescribed by IAEA regulations and national storage acceptance criteria. Subsequently, considerable efforts have been made to optimize impact limiting structures aiming to reduce cask stresses and deformations. Though, their benefits can only fully be exploited, if the energy absorbing behavior is reliable simulated by numerical models which play an increasingly important role in safety assessments.
BAM has had conducted the 5-years research project ENREA in order to overcome the problems caused by the use of simplified, not sufficiently validated or even defective computational concepts for damping materials. While major results of the just recently completed program will be presented, the focus is laid on the question whether these Outputs provide a solid foundation for approximating impact limiting structures in all relevant configurations.
So far, material models have been implemented for spruce, Polyurethane foams and damping concrete based mainly on small and medium scale compression test results. The experimental program performed at BAM comprised likewise guided drop tests and, especially for concrete, penetration tests. Although the resulting numerical simulations showed good agreement with measured values, it turned out to be necessary to consider further effects with regard to e.g. multiaxial stress States, shearfailures of shock absorbing components and their interaction with enclosed or enclosing structures. Thus, the strengths and application constraints of the actual models will be shown as well as details about further research needs, if any.
Zur numerischen Simulation von Transport- und Lagerbehältern für radioaktive Stoffe unter mechanischen Unfallbedingungen sind geeignete
Materialmodelle und zugehörige Parametersätze für alle relevanten Behälterbauteile und den Aufpralluntergrund sowie gegebenenfalls für weitere am Störfall beteiligte Komponenten erforderlich.
Sie bilden eine wesentliche Grundlage um für unterschiedliche Belastungsvarianten und Temperaturen zuverlässige Berechnungsergebnisse zu ermitteln, die umfangreiche experimentelle Erprobungen zumindest in Teilen ersetzen und damit einen zentralen Bestandteil von sicherheitstechnischen Nachweisen in gefahrgut- und atomrechtlichen Zulassungs- und Genehmigungsverfahren bilden können. Für die Auslegung der Behälter von besonderer Bedeutung ist die Effizienz der eingesetzten energieabsorbierenden Elemente, wie beispielsweise Stoßdämpfer am Behälterdeckel oder -boden bzw. äquivalente Strukturen auf oder im Fundament von Zwischen- und Endlagern.
Diese Bauteile, die häufig aus Holz, Polyurethan (PU) - Schaum oder Dämpferbeton hergestellt werden, erfahren beim Auf- oder Anprall erhebliche plastische Deformationen, deren Verteilung und Größenordnung u.a. von der Belastungsgeschwindigkeit, dem Belastungsverlauf und der Temperatur bestimmt werden. Die Berücksichtigung dieser Faktoren in dynamischen Finite Elemente (FE) Berechnungen, die den heutigen Stand der Simulationstechnik repräsentieren, setzt eine systematische Datenbasis für den stoßdämpfenden Werkstoff voraus und die Implementierung dieser Informationen in numerischen Materialformulierungen.
An der BAM wird seit Ende 2008 im Rahmen des vom BMBF geförderten Forschungsvorhabens ENREA (Entwicklung rechnerischer Analysemethoden für stoßdämpfende Strukturen beim Anprall oder Absturz von Abfallgebinden) die experimentelle Bestimmung derartiger Daten sowie die Anpassung und teilweise Neuentwicklung geeigneter Materialmodelle betrieben.