Filtern
Erscheinungsjahr
- 2015 (16) (entfernen)
Dokumenttyp
- Beitrag zu einem Tagungsband (9)
- Vortrag (6)
- Sonstiges (1)
Schlagworte
- Damping concrete (2)
- Finite element method (2)
- Polyurethane foam (2)
- Simulation (2)
- Ageing (1)
- Aging management (1)
- Cask handling accident (1)
- Crushable foam material model (1)
- Damage (1)
- Elastomer (1)
Eingeladener Vortrag
- nein (6)
A Memorandum of Understanding (MOU) between the Federal Institute for Materials Research and Testing (BAM) and Argonne National Laboratory (Argonne) was signed in the fall of 2014. Its objectives are to promote cooperation among scientists and specialists at BAM and Argonne and establish a framework for collaboration in the field of advanced technologies associated with the back end of the nuclear fuel cycle. Collaborative activities involving the BAM and Argonne may be implemented through the promotion of joint research activities and scientific workshops and conferences; the exchange of technical information; and visits by scientists, specialists, and graduate, postgraduate, and Ph.D. students. The first Argonne/BAM workshop was held at Argonne in October 2014 to discuss aging management issues related to the long-term dry storage of spent fuel. Major topics for potential collaboration on the extended storage of spent nuclear fuel and its subsequent transportation were identified.
Transport and storage casks for medium and high level radioactive waste are subjected to extreme heavy loads during the accidental drop scenarios prescribed by IAEA regulations and national storage acceptance criteria. Subsequently, considerable efforts have been made to optimize impact limiting structures aiming to reduce cask stresses and deformations. Though, their benefits can only fully be exploited, if the energy absorbing behavior is reliable simulated by numerical models which play an increasingly important role in safety assessments.
BAM has had conducted the 5-years research project ENREA in order to overcome the problems caused by the use of simplified, not sufficiently validated or even defective computational concepts for damping materials. While major results of the just recently completed program will be presented, the focus is laid on the question whether these Outputs provide a solid foundation for approximating impact limiting structures in all relevant configurations.
So far, material models have been implemented for spruce, Polyurethane foams and damping concrete based mainly on small and medium scale compression test results. The experimental program performed at BAM comprised likewise guided drop tests and, especially for concrete, penetration tests. Although the resulting numerical simulations showed good agreement with measured values, it turned out to be necessary to consider further effects with regard to e.g. multiaxial stress States, shearfailures of shock absorbing components and their interaction with enclosed or enclosing structures. Thus, the strengths and application constraints of the actual models will be shown as well as details about further research needs, if any.
Polyurethane foam used as impact limiter material undergoes high plastic deformations, whereat the resulting stress-strain relations strongly depend on loading speed and temperature. This paper discusses the efforts necessary to develop a reliable numerical foam simulation model focussing on generation and implementation of temperature- dependent yield curves
Elastomer seals are widely used as barrier seals in containers for low and intermediate level radioactive waste and for spent fuel transportation casks. In addition, they are also used for spent fuel storage and transportation casks (dual purpose casks (DPC)) as auxiliary seals to allow leakage rate measurements of metal barrier seals for demonstration of their proper assembling conditions. Depending on the area of use, the rubber materials have to demonstrate proper sealing performance with regard to mechanical, thermal, and environmental conditions as well as irradiation during the entire operation period. Concerning DPC, degradation effects should be limited in a way that, for example, effects from potentially released decomposition elements may not harm e.g. metal barrier seals. Leakage rate measurements should be possible also after long interim storage periods prior to subsequent transportation.
Because of the complex requirements resulting from the various applications of containers for radioactive waste and spent nuclear fuel, BAM has initiated several test programmes for investigating the behaviour of elastomer seals. In this contribution the current status is described and first results are discussed.
Due to delays in the site-selection procedure to establish a deep geological repository for spent nuclear fuel and high level waste and in construction of the already licensed Konrad-repository for low and intermediate level waste without heat generation, extended periods of interim storage become more relevant in Germany. BAM is involved in most of the cask licensing procedures and especially responsible for the evaluation of cask-related long-term safety issues.
The long-term performance of elastomer seals for lid Systems of transport and storage casks whether used as auxiliary seals in spent fuel caslcs or as primary seals for low and intermediate level waste packages is an important issue in this context (Jaunich, 2013; Jaunich, 2014; Kömmling, 2015). The polymeric structure of these seals causes a complex mechanical behaviour with time-dependent elasticity reduction and loss of elastic recovery.
The paper presents first results of a comprehensive test Programme consisting of several static and dynamic mechanical short- and long-term tests which have been carried out at BAM on specimens made of representative types of elastomers, fluorocarbon rubber (FKM) and ethylene propylene diene rubber (EPDM). The investigation of the test results used to identify material models and their Parameters as well as the development of two finite element models for the numerical Simulation of tension and compression tests using the finite element code ABAQUS® are described. The calculation results are presented in comparison to the test results. The influence of important material and test parameters was investigated and discussed in sensitivity analyses.
Abfallgebinde, die im Endlager Konrad eingelagert werden sollen, müssen die Anforderungen und Kriterien erfüllen, die in den Endlagerungsbedingungen (SE-IB-29/08-Rev-1 [1]) und in der Produktkontrolle (SE-IB-30/08-Rev-1) festgelegt sind. Die Qualifizierung der Abfallbehälter erfolgt auf dieser Grundlage in Form von Bauartprüfungen, die von der Bundesanstalt für Materialforschung und -prüfung (BAM) im Auftrag des Bundesamtes für Strahlenschutz (BfS) durchgeführt werden. Darüber hinaus sind die im Hinblick auf Behälterbauartprüfungen relevanten Nebenbestimmungen aus dem Planfeststellungsbeschluss für das Endlager Konrad zu berücksichtigen. Zur besseren Anwendbarkeit werden diese Nebenbestimmungen in die Endlagerungsbedingungen und die Produktkontrolle eingearbeitet. Begleitend ist als Hilfestellung für die Abfallablieferer und Behälterhersteller ein Leitfaden geplant, der praktikable Nachweisstrategien aufzeigt und, soweit erforderlich, Hintergrundinformationen zu den Spezifikationen der Regelwerke liefert. Die BAM ist vom BfS beauftragt, hierfür Vorschläge zu entwickeln und Empfehlungen abzugeben.