Filtern
Erscheinungsjahr
- 2011 (6) (entfernen)
Dokumenttyp
- Zeitschriftenartikel (3)
- Beitrag zu einem Tagungsband (1)
- Vortrag (1)
- Posterpräsentation (1)
Schlagworte
- Atomic force microscopy (2)
- 2, 4, 6-trinitrophenol (1)
- Adhesion force (1)
- CNT (1)
- Degradation (1)
- Dynamic ploughing lithography (1)
- Energetic material (1)
- Epoxy resin (1)
- Fire behavior (1)
- Fire retardancy (1)
Eingeladener Vortrag
- nein (1)
A correlation of adhesion force and electrical conductivity is established for a vanadium oxide and highly oriented pyrolytic graphite (HOPG). Adhesion forces were determined by analysis of pull-off forces obtained from force–distance curves with atomic force microscopy in ultrahigh vacuum, on clean surfaces and with defined contact conditions. The investigated samples include (i) different stoichiometries of Magnéli-type vanadium oxides (V3O5, V4O7, V6O11, and V7O13), which undergo metal-insulator-transitions as a function of temperature, (ii) the (0001) basal plane and the (10–10) prism plane of highly oriented pyrolytic graphite (HOPG), which differ in their respective perpendicular-plane electrical conductivities by several orders of magnitude, and (iii) the (100) surfaces of pure metal single crystals, i.e., silver (Ag), copper (Cu), iron (Fe) and gold (Au). It is shown, that the vanadium oxides as well as the graphite exhibit significantly lower adhesion forces in their electrical conductive state than in their non-electrical conductive state. The values obtained for the electrical conductive states are quantitatively confirmed by the measurements on the single crystal metals.
Observation of nanoscale hot-spot generation on a 2, 4, 6-trinitrophenol (TNP) single crystal
(2011)
An energetic material (EM) creates a local thermal point when it accepts energy and the EM will explode due to thermal decomposition when the hot-spot temperature reaches the explosive temperature. The initial stage of the hot-spot formation on 2, 4, 6-trinitrophenol (TNP) single crystal has been observed at the nanometer scale using atomic force microscopy (AFM). The hot-spot generation has been directly initiated by means of an AFM tip. The phenomenon is accompanied by producing agglomerated spherical-like nanoparticles due to a low-temperature decomposition of TNP. It has been observed that the agglomerated particles are produced outside of the stimulated region. The observed decomposition process at the nanoscale doesn't lead to a self-sustaining shock as detonation or explosion. The results are of interest in relation to explore the origin of deformation-induced chemical decomposition or detonation of EM.
Layered silicate epoxy nanocomposites: formation of the inorganic-carbonaceous fire protection layer
(2011)
The layered silicate (LS) modification and processing parameters applied control the morphology of the LS/polymer composites. Here, increasing the surface area of the LS particles by using alternative drying processes increases dispersion towards a more typical nanocomposite morphology, which is a basic requirement for promising flame retardancy. Nevertheless, the morphology at room temperature does not act itself with respect to flame retardancy, but serves as a prerequisite for the formation of an efficient surface protection layer during pyrolysis. The formation of this residue layer was addressed experimentally for the actual pyrolysis region of a burning nanocomposite and thus our results are valid without any assumptions or compromises on the time period, dimension, surrounding atmosphere or temperature. The formation of the inorganic-carbonaceous residue is influenced by bubbling, migration, reorientation, agglomeration, ablation, and perhaps also delamination induced thermally and by decomposition, whereas true sintering of the inorganic particles was ruled out as an important mechanism. Multiple, quite different mechanisms are relevant during the formation of the residue, and the importance of each mechanism probably differs from one nanocomposite system to another. The main fire protection effect of the surface layer in polymer nanocomposites based on non-charring or nearly non-charring polymers is the increase in surface temperature, resulting in a substantial increase in reradiated heat flux (heat shielding).