Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (21)
- Vortrag (8)
- Sonstiges (5)
- Posterpräsentation (4)
- Beitrag zu einem Tagungsband (3)
- Beitrag zu einem Sammelband (1)
Sprache
- Englisch (42) (entfernen)
Schlagworte
- Mechanical properties (8)
- IIT (4)
- Nanoindentation (4)
- ISO 14577 (3)
- Instrumented indentation testing (3)
- Calibration (2)
- Dynamic testing (2)
- Friction (2)
- Instrumented Indentation Testing (2)
- Multilayer (2)
Organisationseinheit der BAM
- 6 Materialchemie (6)
- 6.7 Materialsynthese und Design (5)
- 6.2 Material- und Oberflächentechnologien (2)
- 9 Komponentensicherheit (2)
- 9.5 Tribologie und Verschleißschutz (2)
- 5 Werkstofftechnik (1)
- 5.1 Mikrostruktur Design und Degradation (1)
- 6.1 Oberflächen- und Dünnschichtanalyse (1)
- 6.6 Physik und chemische Analytik der Polymere (1)
Eingeladener Vortrag
- nein (8)
A calibration procedure for the detection efficiency of energy dispersive X-ray spectrometers (EDS) used in combination with scanning electron microscopy (SEM) for standardless electron probe microanalysis (EPMA) is presented. The procedure is based on the comparison of X-ray spectra from a reference material (RM) measured with the EDS to be calibrated and a reference EDS. The RM is certified by the line intensities in the X-ray spectrum recorded with a reference EDS and by its composition. The calibration of the reference EDS is performed using synchrotron radiation at the radiometry laboratory of the Physikalisch-Technische Bundesanstalt. Measurement of RM spectra and comparison of the specified line intensities enables a rapid efficiency calibration on most SEMs. The article reports on studies to prepare such a RM and on EDS calibration and proposes a methodology that could be implemented in current spectrometer software to enable the calibration with a minimum of operator assistance.
The irradiation of ~0.9-µm-thick hydrogenated amorphous carbon (a-C:H) layers deposited on silicon substrates with single femtosecond (fs) laser pulses (35 fs pulse duration, 790 nm centre wavelength) in air is studied experimentally. Irradiation spots have been generated with different peak fluences and subsequently investigated by optical topometry, micro Raman spectroscopy and microscale mechanical indentation in order to evaluate their microscopic, topographical, structural and mechanical properties (e.g. elastic modulus). By this multi-method approach, a clear separation of different effects (delamination and graphitisation) becomes possible. The joint application of mechanical and spectroscopic techniques provides unique insights into the effects of the fs-laser radiation on the carbon layer.
Laser texturing is an emerging technology for generating surface functionalities on basis of optical, mechanical, or chemical properties. Taking benefit of laser sources with ultrashort (fs) pulse durations features outstanding precision of machining and negligible rims or burrs surrounding the laser-irradiation zone. Consequently, additional mechanical or chemical post-processing steps are usually not required for fs-laser surface texturing (fs-LST). This work aimed to provide a bridge between research in the field of tribology and laser materials processing. The paper reviews the current state-of-the-art in fs-LST, with a focus on the tribological performance (friction and wear) of specific self-organized surface structures (so-called ripples, grooves, and spikes) on steel and titanium alloys. On the titanium alloy, specific sickle-shaped hybrid micro-nanostructures were also observed and tribologically tested. Care is taken to identify accompanying effects affecting the materials hardness, superficial oxidation, nano- and microscale topographies, and the role of additives contained in lubricants, such as commercial engine oil.
An extensive comparison between the conventional Vickers hardness at 500 mN and indentation hardness measured with Vickers indenters at 500 mN is presented for up to 20 different materials and for three different instruments. Additionally, the indentation modulus is compared to Young’s modulus, which was measured with alternative methods or taken from the literature. It is shown that the agreement between the results from depth-sensing indentation and the reference values can be improved by additional corrections, for the calculation of the indentation area. With corrections the mean hardness difference to the Vickers hardness reference as average of all investigated materials can be reduced to about 10 % although disturbing pile-up or sink-in effects can still not be considered. For the modulus, the mean difference was only about 6 %.