Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (22)
- Beitrag zu einem Tagungsband (19)
- Beitrag zu einem Sammelband (2)
- Buchkapitel (1)
- Vortrag (1)
- Posterpräsentation (1)
Schlagworte
- Friction (14)
- Wear (11)
- Hydrogen (10)
- Vacuum (9)
- Graphite (7)
- Vakuum (7)
- PEEK (6)
- Polymers (5)
- Tribologie (5)
- Hydrogen environment (4)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (1)
Tribologisches Verhalten der Werkstoffpaarung Polymerverbundwerkstoff/Stahl bei tiefen Temperaturen
(2005)
In a first test series, the friction and wear properties of 6 polymeric candidate materials for application in LNG tribosystems were tested. The most favorable properties showed PTFE composite, filled with carbon fibers and PEEK, which showed low and stable friction and a wear coefficient in the order of 10-7 mm3N-1m-1. PTFE containing PEEK composites seem to be also appropriate for LNG applications. Admixtures of graphite as solid lubricant result in lower wear. Contrary, a lubricating mechanism of MoS2 was not observed. The PI-materials showed comparatively high friction and medium wear.
The influence of hydrogen environment on the friction and wear behavior of polyimide (PI) composites was investigated for two different PI-types (PI1 and PI2) filled with natural or synthetic graphite. Sliding tests were run against AISI 52100 steel and the worn surfaces as well as the transfer film were analyzed by means of SEM, EDX and Infrared Spectroscopy. Results indicate that the chemical structure of the polyimide has a major influence on the tribological behavior. While the friction of PI2 remains rather stable in all environments, PI1 showed very low friction in hydrogen without any lubricant. The lubricity of graphite was found to be more effective in hydrogen than in moist air.
For further development of hydrogen technology, it is necessary to have a sufficient number of materials for safe and reliable operation available. Frictional contacts exposed to hydrogen, are critical because of vanishing protective oxide layers in the presence of a chemical reducing environment. Furthermore, liquid lubricants are often not applicable, because of purity requirements, or very low temperatures in the case of liquid hydrogen. Thus, for numerous tribosystems in hydrogen technology, solid lubrication is the only possible method for reducing friction and wear. Therefore, investigations on the tribological behaviour of friction reducing materials, such as PTFE, graphite, DLC and MoS2, in inert and hydrogen environment were carried out. The results show that solid lubricants, applied as coatings or as components in polymer composites, are able to reduce friction and wear in gaseous as well as in liquid hydrogen. However, some materials are very sensitive to the environmental medium.
For tribological components working under extreme
conditions, such as vacuum, or broad temperature
ranges, it is often a problem to achieve acceptable
durability of their friction parts. Thus, new material
requirements are involved for these tribo-systems, in
particular regarding operability and reliability. At BAM,
several projects were conducted in the recent years,
dealing with the tribological properties of friction
couples at cryogenic temperature and in vacuum
environment. This paper describes the vacuum and ultra
high vacuum tribometers constructed at BAM and
presents experiments carried out with polymer
composites. The experiments presented were performed
with PEEK, filled with solid lubricants, against 304
steel with a pin-on-disc configuration in oscillating
sliding. Friction tests were carried out in vacuum in the
temperature range between -40°C and +160°C and in
ultra high vacuum at room temperature.
Superconducting magnets are susceptible to quenching, even with the smallest amounts of energy disturbances due to the extremely low thermal capacity of materials at 4.2 K. Hence, small mechanical disturbances resulting in frictional heating can be sufficient to exceed the wire’s critical temperature, causing it to quench. Unfortunately, relative motion between surfaces in the magnet System is inevitable due to various forces present in the System, including winding pretension, differences in material thermal contraction and the large electromagnetic forces. Typically insulating polymers are present at this interface to achieve the required electrical insulation requirements.
Starke Magnetfelder, wie sie z.B. für die Magnetresonanztomografie (MRT) notwendig sind, werden durch supraleitende Spulen erzeugt, die mit Flüssighelium auf eine Temperatur von -269°C gekühlt werden. Die Reibungswärme, die z.B. bei kleinsten Bewegungen zwischen der Spule und deren Stützstruktur entsteht, kann bewirken, dass die kritische Temperatur des Supraleiters lokal überschritten wird und ein normalleitender Bereich entsteht. Aufgrund der bei Normalleitung entstehenden jouleschen Wärme kann sich dieser Bereich weiter erwärmen und schnell ausbreiten. Dieser Vorgang wird als Quench bezeichnet und führt zum schlagartigen Verdampfen des extrem teuren Kältemittels und zu Betriebsunterbrechungen von mehreren Tagen.
Da diese Quenche durch Reibungswärme verursacht werden, ist es notwendig, das Reibverhalten der beteiligten Werkstoffe so zu optimieren, dass kein kritischer Betriebszustand erreicht wird. Dies betrifft in erster Linie Polymerfolien, die zur elektrischen Isolierung zwischen der Spule und der Stützstruktur notwendig sind. Neben zu hoher Reibung allgemein müssen ausgeprägte Haftreibungsspitzen und StickSlip-Effekte vermieden werden. Mit
diesem Ziel wurde das Reibverhalten von PTFE-, PET- und Pl-Folien bei tiefen Temperaturen und den für diese Anwendung typischen niedrigen Gleitgeschwindigkeiten untersucht. Es zeigte sich, dass die Reibung zwischen Polymeroberflächen in Flüssighelium allgemein höher, aber stabiler als in Flüssigstickstoff ist. Allerdings hängt das Reibverhalten erheblich von der Werkstoffpaarung ab. Der Stick-Slip-Effekt nimmt bei allen untersuchten Polymer-Polymer-Paarungen mit wachsender Kontaktpressung zu. PET gegen PET hat das ungünstigste Reibverhalten und sollte bei hohen Pressungen vermieden werden. Zum Vergleich getestete Paarungen von Polymeren gegen Aluminium zeigten deutlich günstigeres Reibverhalten ohne signifikanten Stick-Slip. Deshalb sollte bei derartigen Anwendungen sichergestellt werden, dass die Gleitebene zwischen Polymer- und Metalloberfläche liegt.
In the development of hydrogen technology, special attention is paid to the technical problems of
hydrogen storage. One possible way is cryogenic storage in liquid form. Generally cryotechnical
machines need components with interacting surfaces in relative motion such as bearings, seals or
valves, which are subjected to extreme conditions. Materials of such systems have to be resistant to
friction-caused mechanical deformation at the surface, low temperatures and hydrogen environment.
Since materials failure can cause uncontrolled escape of hydrogen, new material requirements are
involved for these tribo-systems, in particular regarding operability and reliability. In the past few
years several projects dealing with the influence of hydrogen on the tribological properties of friction
couples were conducted at the Federal Institute for Materials Research and Testing, (BAM), Berlin.
This paper reports some investigations carried out with polymer composites. Friction and wear were
measured for continuous sliding and analyses of the worn surfaces were performed after the
experiments. Tests were performed at room temperature in hydrogen as well as in liquid hydrogen.
Aim of the investigation is to characterize selected PEEK-composites in vacuum environment. Oscillating sliding friction was investigated with a pin-on-disc configuration in high vacuum (10-5 mbar) at room temperature, -40 °C, +100 °C and +160 °C. The contact pressure was 1 MPa and 7 MPa respectively , the maximum sliding velocity 0.1 m/s. Furthermore, tests in ultra high vacuum (10-9 mbar) were carried out with flat and spherical pins at 1 MPa and 60 MPa respectively. Among the tested materials MoS2 filled PEEK shows the best tribological performance in vacuum. Particularly, in the lower temperature range and at higher loads the friction behaviour is improved by MoS2 content.
The tribological behavior of neat and filled PEEK and PEKK composites were compared in air and vacuum conditions. Very low friction and wear coefficient were obtained at low sliding speed while severe wear occurred at high speed. Experimental results are discussed by analysing the transfer film and wear debris.
Mittels lasergesteuerter gepulster Vakuumbogentechnologie (Laser-Arc) wurde eine reihe von reinen MoS2-Schichten sowie Kombinationsschichten aus MoS2 und tetraedrischem amorphen Kohlenstoff (ta-C) hergestellt. Mit diesen Schichtvarianten erfolgten tribologische Tests im Vakuum sowie in Atmosphäre. Dabei wurden im Hochvakuum reibungskoeffizienten bis zu 0,005 gemessen. Durch die Verwendung einer ta-C unterschicht konnte eine Lebensdauer von über 5×105 Lastzyklen erreicht werden. Zudem erwies sich diese unterschicht als vorteilhaft für das tribologische Verhalten der MoS2/ta-C Schichten unter atmosphärischen Bedingungen. -------------------------------------------------------------------------------------------------------------------------------------------
A series of MoS2 and combined MoS2/ta-C coatings were prepared by lasercontrolled arc evaporation (Laser-Arc) in order to study the tribological coating behaviour under vacuum and atmospheric conditions. Very low friction coefficients down to 0.005 were measured under high vacuum. By using a ta-C underlayer beneath the MoS2 a increased lifetime up to 5×105 load cycles could be obtained. Also under atmospheric conditions the underlayer had a beneficial effect on coating performance.
This paper presents the mechanical and tribological properties of
Polytetrafluoroethylene (PTFE) and Polyetheretherketone (PEEK)
matrix composites filled with short carbon fibers in cryogenic
environments. Tensile tests were performed at room temperature (RT)
in air and in LN2. Tribological experiments were carried out with a
pin-on-disc configuration at RT, in LN2, in LH2 and in LHe. PEEK
composites have a better tribological performance than PTFE materials
especially regarding the wear resistance.
Influence of the Temperature on the Tribological Behaviour of PEEK Composites in Vacuum Environment
(2008)
This paper describes tribological experiments carried out with polyetheretherketone (PEEK), filled with carbon fibres and solid lubricants (polytetrafluoroethylene (PTFE), graphite or MoS2), against steel discs. Oscillating sliding tests were performed in high vacuum environment in the temperature range between -40°C and +160°C. Results indicate that MoS2 filled PEEK show the best tribological performance in vacuum. Particularly, in the lower temperature range and at higher loads the friction behaviour is improved by the MoS2 content.
Influence of solid lubricant fillers on the tribological behaviour of peek composites in vacuum
(2009)
This paper focuses on the influence of the counterface materials on the sliding behaviour of polymer materials in hydrogen. Polyimide (PI), polyetheretherketone (PEEK) and Polytetrafluoroethylene (PTFE) materials were investigated against hardened 52100 martensitic bearing steel and 304 austenitic stainless steel with similar roughness (Ra = 0.2 μm). Results indicate that the friction and wear of PI and PEEK materials depend on the counterface material. This effect wasn’t observed for PTFE composites. While the tribological performance of polyimide is better against 52100 in hydrogen, improved sliding behaviour of PEEK materials is observed with 304 counterface, particularly at higher sliding speed. Surface analyses of the transfer film reveal that the influence of the counterface is primarily related to the chemical nature of the steel for PI and to the thermal conductivity of the disc for PEEK materials.
The development of hydrogen technologies is a key strategy to reduce greenhouse gas emission worldwide. Power-to-Gas is a challenging solution, in which hydrogen and methane can be used in mobility, industry, heat supply and electricity generation applications. This presentation deals with the tribological behaviour of polymer materials in hydrogen and methane, both in gas and in liquefied form.
Die Reibeigenschaften von PEEK-Materialien gegen Stahlscheiben wurden in Luft, Vakuum und Wasserstoffumgebung untersucht. Die Ergebnisse zeigen, dass reines PEEK umgebungsabhängig ist und die Desorption von Gasen im Vakuum zu hohen Verschleißraten führt. Die niedrigsten Verschleißraten sowohl in Vakuum als auch in einer Wasserstoffumgebung erzielen TiO2-Partikel. Ferner treten chemische Prozesse in den Materialien und im Tribokontakt auf und interagieren miteinander.
Windings in superconducting magnets operating at 4.2 K are highly susceptible to quenching caused by small frictional heat inputs. Small movements in the magnet system are inevitable during ramping due to the increasing electromagnetic forces. Friction pairs of polymer based materials have been investigated at 4.2 K to gain an understanding of their sliding behavior in conditions representative of superconducting MRI systems. The results indicate that polymer-polymer pairs experience unstable sliding behavior with repeated stick-slip whereas polymer-aluminum couples have stable sliding behavior up to high contact pressures of 20 MPa.
This paper presents investigations on the tribological behaviour of PTFE composites against steel at cryogenic temperatures. The results showed that the friction coefficient decreases with temperature down to 77 K, but did not follow a linear evolution further down to extreme low temperatures. It can be stated that the cryogenic environment has a significant influence on the tribological performance of the polymer composites. The effect of low temperatures was more clearly detected at low sliding speed, where friction heat is reduced. A change in wear mechanism from adhesive to abrasive was observed in this case. SEM and AFM analyses showed that the PTFE matrix composites investigated under these experimental conditions have transferred material onto the disc down to very low temperatures. Chemical analyses indicate the presence of iron fluorides.
The sliding performance of PEEK composites was investigated in vacuum environment. Tests were performed with carbon fibre reinforced PEEK composites filled with PTFE, and MoS2 or graphite as further solid lubricant. Polymer samples were tested in a pin-on-disc configuration continuously sliding against CrNi-steel. Depending on sliding speed and temperature, the MoS2 filled composites showed high wear resistance and friction coefficients as low as PVD coatings.
The tribological characteristics of pure and graphite filled polymers were investigated in gaseous hydrogen at ambient temperatures and in LH2 at -253°C. It could be shown that the tribological properties of PI and PEEK materials is related to the formation of a transfer film. The influence of both hydrogen and cryogenic temperatures will be discussed in the presentation.
High performance polymer composites have been intensively investigated for tribological applications in air, but rarely in hydrogen environment. Author's previous benchmark of composites in liquid hydrogen (LH2) showed that graphite filled polymers have beneficial friction behaviour in this extreme condition. Therefore, further investigations have been undertaken in hydrogen environment. This paper presents first results obtained with polyimide composites filled with different types (natural, synthetic) and amounts of graphite in air, vacuum and hydrogen environments. A particular attention is taken to the influence of hydrogen on graphite as well as on the polymer matrix.
Ensuring a sustainable energy supply is currently one of the most important areas for industry and research institutions. Hydrogen technology is a promising candidate, but its broad extension requires extremely high reliability and safety in all areas for common applications as automobiles and stationary fuel cells. Particularly components containing tribosystems are critical parts.
The tribological behaviour of MoS2/ta-C double layer coatings deposited by Laser-Arc technology was investigated in vacuum and air. In vacuum environment, the friction coefficient against steel balls varies between 0.005 and 0.02 depending on the contact pressure. At high contact pressures, the friction coefficient is as low as 0.005 and the life time between 340,000 and 500,000 cycles. Furthermore, it is shown that a ta-C base layer improves the performance of MoS2 coating.
Surface analyses were performed before and after the tribological tests by means of SEM, EDX, XRD, and TEM. They show that in the top layer beneath the sliding surface crystallization of the initially quasi-amorphous MoS2 took place. TEM images also verified an orientation of the basal MoS2-lattice planes parallel to the surface.
Polymers are extensively used for sliding systems in cryogenic applications because of their favourable friction and wear behaviour in the absence of external lubrication. Since important new technologies are based on applications under extreme conditions, such as at low temperatures, new requirements on material properties, in particular regarding their operability and reliability, must be met. Up to now, most tribological investigations have been carried out in inert cryogens or cryogenic gas (He, N2). Few experiments have been performed in vacuum environment at cryogenic temperatures. Rarely were testing in reactive media, such as LH2 or LOX. Due to the wide range of operating conditions in cryogenic applications, it is difficult to state general rules. Therefore, this chapter tends to give an overview on theories and experimental studies on polymer tribology at cryogenic temperatures.
Die tribologischen Eigenschaften von graphitgefüllten Polyimiden gegen Stahl 100Cr6 wurden an Luft, im Hochvakuum (l0⁻ ³ Pa) und in Wasserstoffumgebung bei verschiedenen Drücken (10³ Pa, 10⁴ Pa und 10⁵ Pa) untersucht. Zwei unterschiedliche Polyimid-Typen wurden eingesetzt, wobei Typ und Menge des Graphits variiert wurden.
Die Experimente wurden bei 3,1 MPa Kontaktdruck und einer Gleitgeschwindigkeit von 0,2 m/s bzw. 1 m/s durchgeführt. Die verschlissenen Oberflächen und die Morphologie des Materialübertrags auf die Stahl-Gegenfläche wurden mittels Lichtmikroskopie, REM, TEM und FTIR untersucht. Die Untersuchung zeigt, dass sowohl die Matrix als auch der Graphitanteil einen deutlichen Einfluss auf das Reibverhalten von Verbundwerkstoffen in Wasserstoffumgehungen haben können.
The development of hydrogen technologies entails high safety requirements in distribution and dispensing infrastructure. Therefore, it is necessary to pursue research on material compatibility in hydrogen, especially for critical parts with tribological issues.
The focus of this study is to evaluate the influence of hydrogen on a wider range of commercially available polymer materials. Thereby, the friction and wear behavior of different grades of TPE, POM, PA66, PA12, PPA, PEEK, PPS, PTFE, PAI, PI and PBI were investigated against a rotating steel disk (AISI 304). Filled and unfilled polymers from different suppliers were evaluated at room temperature in air, vacuum and hydrogen gas (H2) as well as in liquid hydrogen at - 253°C (LH2).
The sliding behavior of the polymer materials is discussed by means of surface analyses, whereby special attention is paid to the formation of a transfer film.
According to the results at ambient temperature, the effect of hydrogen environment on the tribological behavior of neat polymers may be related to lack of moisture, but also to saturated hydrocarbons in gaseous hydrogen. In liquid hydrogen, the best tribological performances were achieved with neat PA polymers as well as PPS and PI composites.
The focus of this study is to evaluate the influence of hydrogen on the friction and wear behavior of a wide range of polymer materials. Thereby, the tribological performance of filled und unfilled polymers from different suppliers were compared at room temperature in air and hydrogen gas (H2) as well as in liquid hydrogen at -235°C (LH2).