Filtern
Erscheinungsjahr
Dokumenttyp
- Vortrag (35)
- Beitrag zu einem Tagungsband (32)
- Zeitschriftenartikel (31)
- Beitrag zu einem Sammelband (6)
- Posterpräsentation (6)
- Buchkapitel (3)
- Dissertation (1)
Sprache
- Englisch (65)
- Deutsch (47)
- Französisch (2)
Schlagworte
- Friction (28)
- Hydrogen (24)
- Wear (24)
- Polymers (14)
- Vacuum (12)
- Tribology (10)
- Cryogenic temperature (9)
- PEEK (9)
- Polymer composites (9)
- Vakuum (9)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (35)
The polymer chemical structure of the polyimide has a major influence on the tribological behaviour. The addition of graphite in PI2 has a beneficial effect in hydrogen on the friction and wear. The low friction of graphite is associated with a lubricant film in hydrogen. The influence of hydrogen on graphite is more effective than humidity. CNTs have a similar effect to that of graphite in PEEK composites. TiO2 particles improve significantly the wear rate both in vacuum and hydrogen environment. In LH2 friction and wear decrease for unfilled polymers. Friction of graphite filled composites increases slightly and wear rate is stable.
The development of hydrogen technologies is a key strategy to reduce greenhouse gas emission worldwide. Power-to-Gas is a challenging solution, in which hydrogen and methane can be used in mobility, industry, heat supply and electriity generation applications. This presentation deals with the tribological behaviour of polymer materials in hydrogen and methane, both in gas and in liquid form.
Tribologisches Verhalten der Werkstoffpaarung Polymerverbundwerkstoff/Stahl bei tiefen Temperaturen
(2003)
Tribologisches Verhalten der Werkstoffpaarung Polymerverbundwerkstoff/Stahl bei tiefen Temperaturen
(2003)
Tribologisches Verhalten der Werkstoffpaarung Polymerverbundwerkstoff/Stahl bei tiefen Temperaturen
(2005)
In a first test series, the friction and wear properties of 6 polymeric candidate materials for application in LNG tribosystems were tested. The most favorable properties showed PTFE composite, filled with carbon fibers and PEEK, which showed low and stable friction and a wear coefficient in the order of 10-7 mm3N-1m-1. PTFE containing PEEK composites seem to be also appropriate for LNG applications. Admixtures of graphite as solid lubricant result in lower wear. Contrary, a lubricating mechanism of MoS2 was not observed. The PI-materials showed comparatively high friction and medium wear.
The influence of hydrogen environment on the friction and wear behavior of polyimide (PI) composites was investigated for two different PI-types (PI1 and PI2) filled with natural or synthetic graphite. Sliding tests were run against AISI 52100 steel and the worn surfaces as well as the transfer film were analyzed by means of SEM, EDX and Infrared Spectroscopy. Results indicate that the chemical structure of the polyimide has a major influence on the tribological behavior. While the friction of PI2 remains rather stable in all environments, PI1 showed very low friction in hydrogen without any lubricant. The lubricity of graphite was found to be more effective in hydrogen than in moist air.
For further development of hydrogen technology, it is necessary to have a sufficient number of materials for safe and reliable operation available. Frictional contacts exposed to hydrogen, are critical because of vanishing protective oxide layers in the presence of a chemical reducing environment. Furthermore, liquid lubricants are often not applicable, because of purity requirements, or very low temperatures in the case of liquid hydrogen. Thus, for numerous tribosystems in hydrogen technology, solid lubrication is the only possible method for reducing friction and wear. Therefore, investigations on the tribological behaviour of friction reducing materials, such as PTFE, graphite, DLC and MoS2, in inert and hydrogen environment were carried out. The results show that solid lubricants, applied as coatings or as components in polymer composites, are able to reduce friction and wear in gaseous as well as in liquid hydrogen. However, some materials are very sensitive to the environmental medium.
For tribological components working under extreme
conditions, such as vacuum, or broad temperature
ranges, it is often a problem to achieve acceptable
durability of their friction parts. Thus, new material
requirements are involved for these tribo-systems, in
particular regarding operability and reliability. At BAM,
several projects were conducted in the recent years,
dealing with the tribological properties of friction
couples at cryogenic temperature and in vacuum
environment. This paper describes the vacuum and ultra
high vacuum tribometers constructed at BAM and
presents experiments carried out with polymer
composites. The experiments presented were performed
with PEEK, filled with solid lubricants, against 304
steel with a pin-on-disc configuration in oscillating
sliding. Friction tests were carried out in vacuum in the
temperature range between -40°C and +160°C and in
ultra high vacuum at room temperature.
Thermal shock cycle experiments between room and cryogenic temperatures on polymer composites
(2002)
Superconducting magnets are susceptible to quenching, even with the smallest amounts of energy disturbances due to the extremely low thermal capacity of materials at 4.2 K. Hence, small mechanical disturbances resulting in frictional heating can be sufficient to exceed the wire’s critical temperature, causing it to quench. Unfortunately, relative motion between surfaces in the magnet System is inevitable due to various forces present in the System, including winding pretension, differences in material thermal contraction and the large electromagnetic forces. Typically insulating polymers are present at this interface to achieve the required electrical insulation requirements.
Outstanding features favour the application of polymers and polymer composites in low-temperature technology. The booming hydrogen technology is a challenge for these materials, which are considered as seals and bearings in cryogenic pumps. In the present study, three types of thermoplastics, i.e., polyetheretherketone (PEEK), polyetherimide (PEI) and polyamide 6,6 (PA6,6), and one epoxy were considered as matrix materials. Micron-sized fillers, i.e., short carbon fibres, graphite flakes, and PTFE powders, were incorporated into these polymers together with nano-sized TiO2 particles. Optimised compositions of each matrix were selected from our previous works at room temperature in order to be studied at very low temperature conditions. In particular, frictional tests were carried out with polymer composite pins against polished steel surfaces under constant load over a certain distance in liquid hydrogen and liquid nitrogen. Afterwards, worn surfaces were analysed by using scanning electron microscopy (SEM). It was found out that the tribological properties in liquid hydrogen are dominated by the matrix materials, in particular thermoplastics perform generally slightly better than thermosetting resins.
This lecture deals with the sliding behaviour of polymer materials in hydrogen environment. After a short introduction of the hydrogen activities at BAM, the tribological performances of polymer materials in gaseous hydrogen are presented and compared with air and vacuum environment. The second part focusses on the influence of the counterface materials in hydrogen. Finally, the last section is dedicated to experiments liquid hydrogen.
Starke Magnetfelder, wie sie z.B. für die Magnetresonanztomografie (MRT) notwendig sind, werden durch supraleitende Spulen erzeugt, die mit Flüssighelium auf eine Temperatur von -269°C gekühlt werden. Die Reibungswärme, die z.B. bei kleinsten Bewegungen zwischen der Spule und deren Stützstruktur entsteht, kann bewirken, dass die kritische Temperatur des Supraleiters lokal überschritten wird und ein normalleitender Bereich entsteht. Aufgrund der bei Normalleitung entstehenden jouleschen Wärme kann sich dieser Bereich weiter erwärmen und schnell ausbreiten. Dieser Vorgang wird als Quench bezeichnet und führt zum schlagartigen Verdampfen des extrem teuren Kältemittels und zu Betriebsunterbrechungen von mehreren Tagen.
Da diese Quenche durch Reibungswärme verursacht werden, ist es notwendig, das Reibverhalten der beteiligten Werkstoffe so zu optimieren, dass kein kritischer Betriebszustand erreicht wird. Dies betrifft in erster Linie Polymerfolien, die zur elektrischen Isolierung zwischen der Spule und der Stützstruktur notwendig sind. Neben zu hoher Reibung allgemein müssen ausgeprägte Haftreibungsspitzen und StickSlip-Effekte vermieden werden. Mit
diesem Ziel wurde das Reibverhalten von PTFE-, PET- und Pl-Folien bei tiefen Temperaturen und den für diese Anwendung typischen niedrigen Gleitgeschwindigkeiten untersucht. Es zeigte sich, dass die Reibung zwischen Polymeroberflächen in Flüssighelium allgemein höher, aber stabiler als in Flüssigstickstoff ist. Allerdings hängt das Reibverhalten erheblich von der Werkstoffpaarung ab. Der Stick-Slip-Effekt nimmt bei allen untersuchten Polymer-Polymer-Paarungen mit wachsender Kontaktpressung zu. PET gegen PET hat das ungünstigste Reibverhalten und sollte bei hohen Pressungen vermieden werden. Zum Vergleich getestete Paarungen von Polymeren gegen Aluminium zeigten deutlich günstigeres Reibverhalten ohne signifikanten Stick-Slip. Deshalb sollte bei derartigen Anwendungen sichergestellt werden, dass die Gleitebene zwischen Polymer- und Metalloberfläche liegt.
Many new technologies are based on applications in extreme conditions, such as at low temperatures or in hydrogen environment. This involves new requirements on material properties, in particular regarding their operability and reliability. To fulfil this demand, the tribological behaviour of PTFE- and PEEK-matrix composites filled with carbon fibres were investigated at cryogenic temperatures and in hydrogen by means of surface analyses. For a better understanding of the tribological behaviour, and because of the temperature-dependent characteristics of polymer materials, thermal and mechanical properties of selected composites were initially investigated at low temperatures. Thermal shock experiments as well as cryo- and hydrogen treatments were carried out. Different coefficients of thermal expansion within the composite lead to debondings of particles, particularly in the case of PTFE materials. Tensile tests indicate that the YOUNG'S modulus increases at T= 77 K compared to room temperature. However, this improvement at low temperatures is moderate for PEEK composite which is already under its glass transition at room temperature. In the main investigation, tribological experiments were carried out at first at T= 77 K to observe the influence of the matrix, fillers and fibres on the material behaviour comparing to room temperature. The reduction of the friction coefficient and wear at low temperatures has been attributed to the low temperature properties of the polymer in particular due to the higher YOUNG'S modulus at T= 77 K. Whereas at room temperature friction and wear depend strongly of the CF content, the quantity of fillers and fibres does not have a significant effect on the tribological behaviour at low temperatures. At T= 77 K, the tribological behaviour of PTFE and PEEK composites is mainly influenced by the matrix. PEEK composites have a better tribological performance than PTFE materials especially regarding the wear resistance. Furthermore, the influence of the cryogenic medium was determined with experiments carried out in LN2 (T= 77 K), LH2 (T= 20 K) and LHe (T= 4.2 K), as well as in helium at T= 77 K and hydrogen at room temperature. The thermal properties of the cryogenic medium have a significant influence on the tribological performances of the composites. Due to the lower frictional heat at low sliding speed, the effect of low temperatures on the tribological behaviour of these composites was more clearly detected in this case, with a change in wear mechanism from mainly adhesive to more abrasive. Experiments in LN2 give the best friction and wear performance at low as well as at high sliding speed. The behaviour of these composites in LHe does not benefit from the low temperature properties of polymers due to the low heat of evaporation of LHe. The influence of hydrogen was particularly seen after the tribological experiments performed in LH2 on the surface of the disc. The reduction effect of hydrogen may have an influence on the tribochemical reactions which appear during sliding, enhancing the formation of iron fluorides, but no influence of the metal fluorides on the tribological performance could be determined in this study.
In the development of hydrogen technology, special attention is paid to the technical problems of
hydrogen storage. One possible way is cryogenic storage in liquid form. Generally cryotechnical
machines need components with interacting surfaces in relative motion such as bearings, seals or
valves, which are subjected to extreme conditions. Materials of such systems have to be resistant to
friction-caused mechanical deformation at the surface, low temperatures and hydrogen environment.
Since materials failure can cause uncontrolled escape of hydrogen, new material requirements are
involved for these tribo-systems, in particular regarding operability and reliability. In the past few
years several projects dealing with the influence of hydrogen on the tribological properties of friction
couples were conducted at the Federal Institute for Materials Research and Testing, (BAM), Berlin.
This paper reports some investigations carried out with polymer composites. Friction and wear were
measured for continuous sliding and analyses of the worn surfaces were performed after the
experiments. Tests were performed at room temperature in hydrogen as well as in liquid hydrogen.
Aim of the investigation is to characterize selected PEEK-composites in vacuum environment. Oscillating sliding friction was investigated with a pin-on-disc configuration in high vacuum (10-5 mbar) at room temperature, -40 °C, +100 °C and +160 °C. The contact pressure was 1 MPa and 7 MPa respectively , the maximum sliding velocity 0.1 m/s. Furthermore, tests in ultra high vacuum (10-9 mbar) were carried out with flat and spherical pins at 1 MPa and 60 MPa respectively. Among the tested materials MoS2 filled PEEK shows the best tribological performance in vacuum. Particularly, in the lower temperature range and at higher loads the friction behaviour is improved by MoS2 content.
This study deals with the development of PEEK (polyehteretherketone) and PTFE (polytetrafluoroethylene) based composites, optimized for low friction and low wear performance under extreme environments. It is demonstrated that the incorporation of a harder polymer component into PTFE (such as PEEK particles), a short fiber reinforcement (e.g. carbon fibers CF), and internal lubricants (e.g. PTFE particles), helps to reduce the friction and to improve the wear resistance over a very wide temperature range.
This lecture deals with the sliding behaviour of polymer composites in vacuum environment. At first, the effect of the polymer matrix and solid lubricants such as graphite and MoS2 are presented. The second part focusses on the influence of the residual pressure with experimental results obtained in high and ultrahigh vacuum.
The tribological behavior of neat and filled PEEK and PEKK composites were compared in air and vacuum conditions. Very low friction and wear coefficient were obtained at low sliding speed while severe wear occurred at high speed. Experimental results are discussed by analysing the transfer film and wear debris.
The tribological behavior of PAEK composites were investigated in air and vacuum environment. Results indicate that the tribological performance of these compounds depends on material compositions, fiber orientation as well as test conditions. In vacuum, very low friction and wear coefficient were obtained at low sliding speed while severe wear occurred at high speed.