Filtern
Erscheinungsjahr
Dokumenttyp
- Beitrag zu einem Tagungsband (94) (entfernen)
Schlagworte
- Concrete (20)
- Monitoring (16)
- Ultrasound (15)
- Ultraschall (7)
- Coda wave interferometry (6)
- Beton (5)
- Integrity (4)
- Non-destructive testing (4)
- Parallel seismic (4)
- Qualitätskontrolle (4)
Organisationseinheit der BAM
- 8 Zerstörungsfreie Prüfung (39)
- 8.2 Zerstörungsfreie Prüfmethoden für das Bauwesen (38)
- 7 Bauwerkssicherheit (3)
- 8.6 Faseroptische Sensorik (3)
- 8.0 Abteilungsleitung und andere (2)
- 8.1 Sensorik, mess- und prüftechnische Verfahren (2)
- 7.2 Ingenieurbau (1)
- 7.4 Baustofftechnologie (1)
- 7.6 Korrosion und Korrosionsschutz (1)
- 9 Komponentensicherheit (1)
Defect detection in concrete pile using impulse response measurements with sine sweep excitations
(2015)
For pile integrity inspection, a low cost and portable shaker was used to create the sine sweep signal for pile excitation. The impulse response function, calculated by the deconvolution of pile response from the sine sweep excitation, was proposed to identify the echoes in the piles due to the pile’s impedance changes. The proposed methodology has been evaluated and validated both numerically and experimentally. Based on the results from the simulations and experiments, it was found that the impulse response measurement with sine sweep excitation could be an effective tool to detect the echoes of the pile toe and the defects in the pile.
The necessity and demand for nondestructive testing of wood-based materials which can automatically scan huge areas of wood is increasing. Air-coupled ultrasound (ACU) is used to detect defects and damage without altering the structure permanently. Using through transmission it is possible to detect even small holes and missing adhesive. If only one side of an object is accessible the reflection mode is preferred at the expense of a reduced resolution and penetration depth. Novel ferroelectret transducers with a high signal-to-noise ratio (SNR) enable a high-precision structure recognition. The transducers made of cellular polypropylene (PP) are quite suitable for ACU testing due to their extremely low Young’s modulus and low density which result in a favorable acoustic impedance for the transmission of ultrasonic waves between the transducer and air. Thus, defects such as delamination, rot, and cracks can be detected. Promising results were obtained under laboratory conditions with frequencies from 90 kHz to 200 kHz. The advantage of these ACU transducers is that they do not require contact to the sample, are accurate, and cost effective. Ultrasonic quality assurance for Wood is an important attempt to increase the acceptance of wooden structures and towards sustainability in civil engineering in general.
The detection of delamination, rot and cracks causing a decrease of strength in wooden construction elements is a key task for nondestructive testing (NDT). Air-coupled ultrasound (ACU) is used to detect flaws without having to provide contact to the surface or otherwise affect the object. Novel ferroelectric transducers with a high signal-to-noise ratio enable an accurate flaw detection. Transducers made of cellular polypropylene (PP) are suitable for characterizing wood-based materials (WBM) because their extremely low Young’s modulus and low density mean a favorable acoustic impedance for the transmission of ultrasonic waves between the transducer and air. The transducers can be applied during the production of WBM and during its service life. The device enables a fast in-situ recognition of defects with frequencies between 90 kHz and 250 kHz. Measurements can be performed in through transmission for a high resolution or in pulse-echo technique in case of one-sided access at the expense of reduced signal strength. Ultrasonic quality assurance for wood is an important attempt to increase the acceptance of wooden structures and towards sustainability in civil engineering in general.
In der aktuellen Projektphase liegt der Fokus auf der Datenaufnahme, -bearbeitung und -speiche-rung mit dem Ziel, automatisierte Auswerteverfahren einsetzen zu können. Aktuell wurden primär punktuelle Messungen an ausgewählten Messtagen aufgenommen. Die Systeme sollen so weiter-entwickelt werden, dass sie sich auch für kontinuierliche Messungen im Rahmen von Monitoring-aufgaben eignen.
Ein wichtiger Fokus bei der Auswertung ist die Kombination mit numerischen Modellen, die mithilfe von Bayesian Update Verfahren und den aufgenommenen Messdaten kalibriert und im Verlauf der Monitoringaufgabe angepasst werden sollen. Insbesondere sollen auch zeitabhängige Modelle, die eine zeitliche Entwicklung von Struktureigenschaften beinhalten (Kriechen, Schwinden, Ermüdung, Korrosion) dazu verwendet werden, die zukünftige Performance der Struktur bewerten zu können. Basierend darauf werden dann Konzepte zur Planung von Inspektion und Wartung erstellt.
The duraBASt area at the highway intersection “Köln-Ost” is a large test field for road testing.
It includes the duraBASt test bridge which is approximately 66 m long and 14.25 m broad. This bridge is part of the “road in the 21st Century” project and is equipped with several sensors for structural health monitoring. This feasibility study is carried out to investigate the prerequisites necessary for the constraction of intelligent bridges in the foture. Embedded sensors are able to measure quantities such as temperature, strain, moisture, corrosion, etc. In the presented work, the focus is set on passive RFID-based sensors. The communication and energy supply are realised by a mobile transmitter through the concrete cover. Hence, no cables or batteries are required. The sensors are designed to withstand the alkaline environment in concrete. Thus, moisture and corrosion values are measurable for several decades.
Utilization of coherent phase information in complex wave fields forms the basis of interferometric time series analysis. The concept is known since decades, but until about 15 years ago there have been no practical implementations. Meanwhile seismic interferometry is used in a wide range from investigations of the earth’s deep crust to engineering applications. Focused on monitoring and imaging the MIIC (Monitoring and Imaging based on Interferometric Concepts) project as part of the German GeoTechnologien program has contributed to this development. Special attention was given to the transfer of methodology to different length scales that range from centimeters, in laboratory applications, over geotechnical scales to even kilometers in seismological applications. General purpose methods and open source software was developed, which can be used on all scales. The core of the MIIC software is a Python library organized in different modules for various processing tasks. A graphical user interface facilitates the creation of processing routines by visualizing connections and dependencies of variables and by checking the consistency of data types. Example applications have included carbon sequestration, salt mine and railroad embankment monitoring as well as imaging changes in concrete constructions.
Concrete structures are invaluable assets to a society and managing them efficiently and effectively can be supported by information gathered through structural health monitoring (SHM). In this paper, a combined approach based on passive, i.e., acoustic emission (AE), and active, i.e., ultrasonic stress wave (USW) monitoring techniques for application to concrete structures is proposed and evaluated. While AE and USW are based on the same underlying physics, i.e., wave motion in solids, they differ fundamentally with respect to the nature of the source. For the former, external stimuli such as mechanical loads or temperature cause the rapid release of energy from initially unknown locations. As a result, AE events are unique and cannot be repeated. For the latter, a known source at a known location is employed at a specified time. This approach is thus controlled and repeatable. It is
argued that a combination of these two techniques has the potential to provide a more comprehensive picture of ongoing fracture processes, damage progression, as well as slowly occurring aging and degradation mechanisms.
This combined approach does thus promise new opportunities to support condition assessment of concrete structures. After providing an overview and comparison of the two techniques, results, and observations from a full-scale laboratory experiment and an in-service bridge monitoring study are discussed to demonstrate the promise of the proposed combined monitoring approach. Finally, suggestions for further work are presented.