Filtern
Erscheinungsjahr
Dokumenttyp
- Vortrag (142)
- Beitrag zu einem Tagungsband (106)
- Zeitschriftenartikel (87)
- Beitrag zu einem Sammelband (47)
- Posterpräsentation (40)
- Buchkapitel (5)
- Sonstiges (3)
- Forschungsbericht (3)
- Corrigendum (2)
- Dissertation (1)
Schlagworte
- Concrete (87)
- Ultrasound (80)
- Monitoring (59)
- Coda wave interferometry (28)
- Non-destructive testing (23)
- Ultraschall (22)
- NDT (20)
- Imaging (19)
- Zerstörungsfreie Prüfung (15)
- Beton (14)
Organisationseinheit der BAM
- 8 Zerstörungsfreie Prüfung (128)
- 8.2 Zerstörungsfreie Prüfmethoden für das Bauwesen (125)
- 7 Bauwerkssicherheit (8)
- 8.6 Faseroptische Sensorik (5)
- 7.2 Ingenieurbau (4)
- 7.4 Baustofftechnologie (3)
- 8.1 Sensorik, mess- und prüftechnische Verfahren (3)
- 8.4 Akustische und elektromagnetische Verfahren (3)
- 8.5 Röntgenbildgebung (3)
- 8.0 Abteilungsleitung und andere (2)
Paper des Monats
- ja (3)
The reuse of existing foundations is considered in various construction Projects to save time and costs while avoiding unnecessary interference with other underground objects. Because the design and as-built drawings might not be complete and questions may arise regarding the condition of the foundations, a detailed investigation is a prerequisite for the planning process in most cases. Nondestructive testing (NDT) techniques are a core part of this endeavor.
The processes and procedure for foundation reuse planning are not yet standardized, and the possibilities and limitations of NDT methods are not known to many planners and stakeholders. The German research Project REFUND (2014–2016) has developed charts for the planning and Investigation process that consider available standards and the current state of the art in NDT.
These charts are separately available for single and strip, slab, and pile foundations. Available NDT methods have been compiled and evaluated for specific tasks at these foundation types, including their respective limitations.
The procedures have been successfully tested in two real-world projects. The results from these projects enable planners to improve the reliability of the process while potentially saving significant resources. This paper discusses the procedures for pile foundations and demonstrates the use of various NDT methods in a project on the reuse of electrical tower foundations.
Numerous case histories show evidence that geophysical
methods are valuable tools for levee inspection and
monitoring. National and international standards and
recommendations recommend the use of geophysics for a
variety of tasks. However, in some cases reported have
been flaws missed or false indications given. Due to the
larger variety in type, size and construction of levees and
the even larger variety of potential tasks and targets the
success of geophysical surveys still pretty much depends on
the available budget and the experience and capabilities of
the clients and contractors involved.
It is strongly recommended that all relevant parties agree
on the detailed objectives of the survey, required accuracy
and reliability of the results and any follow up measures.
For the most common tasks more research and practical
work using techniques as POD (probability of detection),
which are well established in other fields of non-destructive testing, would be of benefit.
Modern geophysical methods might be either directly applied to foundations or integrated into existing testing schemes to assist in quality assurance and inspections. This paper gives an overview on available ideas and some more detailed examples from the author `s work including:
- Vibrator technologies to improve pile integrity testing.
- Ideas from vertical seismic profiling used in multichannel pile inspection
- Cross- and downhole seismics to check the diameter of jet grouting columns
- Improving the parallel seismic methods for precise length measurement of piles and foundation walls
Seismic migration methods to improve ultrasonic imaging of foundation slabs
Seismological tools to monitor subtle changes in concrete constructions
The author strongly believes that the cooperation between geophysics and civil engineering, which is obviously becoming stronger and stronger, will lead to a large number of innovative approaches for investigations tasks currently still unresolved. A lot of challenges and chances for science and technology are right here.
Innovative seismic and resistivity tools for determining the diameter of jet grouting columns
(2016)
Jet grouting is used for soil improvement, foundation support and groundwater low control all over the world. It is well accepted and subject of standardization in many countries. However, some issues with the method remain. As the grout columns are produced in the subsurface without visual control in an often inhomogeneous soil, the prediction of the column’s diameter is still a challenge. All methods applied so far have their limitations.
The approach presented in this study is twofold. At Colorado School of Mines a resistivity probe has been developed, which is pushed into the fresh grout directly after production. ERT sections are measured and inverted. Given some background information is available, the diameter of the columns can be evaluated.
At BAM the focus has been on post-production investigations using seismic borehole methods. After hardening of the concrete seismic waves are sent through the column downhole (sensors placed in a casing in the column’s axis, source on top) and crosshole (source and sensor in boreholes on opposite sides of the column). We have developed a scheme to evaluate the diameter of the column based on travel time measurements without calibration. As this method is eventually more time and cost intensive we assume its application mainly for test columns. These are casted and dug out for visual inspection to determine appropriate grouting parameters. Our method would replace the often very cost intensive visual inspection.
Both approaches have been tested at three test columns produced at BAM’s test site at Horstwalde, Germany and on an actual constructions site. Both methods have been in good agreement with the diameters predicted by the jet grouting contractors, which were confirmed in one case by mechanical measurements.
The legend continued: The International Symposium NonDestructive Testing in Civil Engineering (NDT-CE) had returned to Berlin. The Bundesanstalt für Materialforschung und -prüfung (BAM) and the Technical University of Berlin (TUB) hosted this prestigious event in the industrial landmark building Peter-Behrens-Halle and the Test Site Technical Safety (TTS) in Horstwalde in September 2015. Almost 300 participants from more than 35 countries gathered to present recent research, exchange knowledge and to lest the newest equipment in NDT-CE. This symposium, held regularly in various locations all over the world, was organized for the third time in Berlin and is by far the largest of its kind.
Recent years have seen extended use of ultrasonic techniques for concrete infrastructure assessement. They are applied for quality assurance and condition assessement at bridges, power plants, dams and other important objects. However, there are still a couple of significant limitations. They include, but are not limited to depth of penetration, imaging complex structures or early stage detections of distributed damage. The talk will give information on recent research in this area. Specifically, the application of the unique deep penetration system LAUS is shown. Ultrasonic monitoring using embedded transducers to check for subtle and sudden changes in the material is introduced as well. Comments on initiatives for validation, standardization and certification will be given.
Civil engineering industry is one of the most important industry sectors in the world-wide economy. It contributes significantly to the gross economic product and general employment. Even more important, it provides many of the basic needs of the society (e. g. housing, infrastructure, protection from natural hazards).
The concept of “Industry 4.0” or “Smart Production” has not yet made significant progress in the civil engineering industry. The design, build and operate processes are still widely dominated by the exchange of printed documents and drawings. Most objects (buildings and other constructions) are unique, and a large part of the production still requires a large amount of manual labor. As-built documentation and quality assurance are often neglected. Civil engineering is among the industries sectors with the lowest level of digitalization and the lowest gain in productivity.
However, this is going to change. In the past decade, several drivers have challenged the ways clients, contractors, and authorities currently operate. These drivers include but are not limited to an increasing demand for serialization and automatization, the mandatory introduction of “Building Information Modeling” (BIM) in public procurement, the availability of construction equipment with sensors and digital interfaces or emerging automated construction technologies such as 3D-printing.
NDE (referred to as NDT-CE in this sector), after a rapid technological development in the last two decades, plays an increasing role in quality assurance, condition assessment and monitoring of structures. However, with very few exceptions, applications are mostly non-standardized and performed only at selected sites. To change this, the NDT-CE community including manufacturers, service providers, clients and the scientific community must work consistently on open data formats, interfaces to BIM, standardization and validated ways for a quantitative use of the results in the assessment of constructions.
This presentation summarizes the opbjectives and the progress of the EURATOM project PREDIS (pre-disposal management of radioactive waste) and its workpackage 7 in particular. Focus is on the development of wireless sensors for monitoring radioactive waste packages, measuring radiation, temperature, pressure and humidity.
According to the NBI database, more than 21,000 in-service U.S. bridges lack sufficient structural documentation necessary for analytical load rating. Among these are a significant proportion of older prestressed concrete bridges. Given the lack of documentation on the reinforcing layout, such structures cannot be load rated analytically and are often subject to engineering judgement as the basis for rating. Otherwise, the typical approach for load rating such bridges is to conduct costly proof load testing and destructive probing together with making conservative assumptions. Therefore, any improvement to current practices will benefit DOTs and taxpayers alike. Accurately reconstructed 3D images of the girders to reflect the internal reinforcement could mitigate the need for costly, if not impractical, destructive testing and proof load testing, and help reduce dependency on conservative assumptions. This study examines a comprehensive NDE approach using ultrasonic tomography and GPR to aid in gathering structural information for load rating purposes. Different types of AASHTO and hollow core girders were tested.