Filtern
Dokumenttyp
- Zeitschriftenartikel (44)
- Vortrag (26)
- Beitrag zu einem Tagungsband (14)
- Buchkapitel (5)
- Forschungsbericht (1)
Schlagworte
- Klärschlamm (10)
- Phosphor (10)
- Phosphorus (9)
- Phosphorus recovery (9)
- Phosphorrückgewinnung (7)
- Recycling (7)
- Sewage sludge (7)
- Klärschlammasche (5)
- Wastewater (5)
- Fertilizer (4)
Organisationseinheit der BAM
- 4 Material und Umwelt (90) (entfernen)
Paper des Monats
- ja (3)
There is an ongoing debate on European scale concerning the criticality of phosphorus. In Switzerland and Germany, phosphorus recovery from phosphorus-rich waste streams will become obligatory. Sewage sludge ash is rich in phosphorus and may become an important secondary feedstock. Thermochemical treatment of sewage sludge ash with sodium sulphate under reducing conditions was shown to remove heavy metals from the solid product and produce the fully plant available crystalline phase CaNaPO4. Pilot-scale experiments in a rotary kiln were carried out at temperatures between 750 and 1000 °C and were compared to laboratory-scale experiments with crucibles. Process upscaling was successfully demonstrated but a series of differences were noticed: In comparison to laboratory-scale, solubility of phosphorus in samples from pilot-scale experiments was lower at all chosen treatment temperatures because of shorter retention time and incomplete decomposition of sodium sulphate. X-ray diffraction analysis revealed remaining phase fractions of whitlockite (Ca3-x(Mg,Fe)x(PO4)2) and sodium sulphate from the starting materials in products and thus indicated incomplete reaction. In contrast to the results of laboratory-scale experiments, the crystalline phase CaNaPO4 was clearly absent in the products from the rotary kiln but instead a Mg-bearing phase (Ca,Mg)NaPO4 was formed. Laboratory-scale experiments confirmed (Ca,Mg)NaPO4 is an intermediate phase between whitlockite and CaNaPO4. However, both crystalline phases are characterized by high plant availability. It was shown that heavy metal removal increased at higher temperatures whereas solubility and thus plant availability of phosphorus already reached its maxima at temperatures of 950 °C in pilot-scale and 875 °C in laboratory-scale experiments.
Die Zementindustrie und weitere energieintensive Industrien wie etwa die Stahlindustrie stehen vor dem Hintergrund der Transformation unserer Gesellschaft zur Klimaneutralität vor erheblichen Herausforderungen. Ziel dieser Branchen ist perspektivisch die vollständige Vermeidung klimaschädlicher Emissionen – mit besonderem Fokus auf Kohlendioxid. Neben der Umstellung auf regenerative Energieträger, sind im Speziellen für die Zementindustrie die erheblichen Anteile an CO2-Emissionen durch die Entsäuerung von Kalkstein zukünftig zu vermeiden. Da die hervorragenden Bindemitteleigenschaften des bisher hauptsächlich in Zementen eingesetzten Portlandklinkers jedoch auf Calciumverbindungen wie Tri- und Di-calciumsilikaten basieren, stellt die Substitution des Kalks derzeit für die Zementindustrie die größte Herausforderung dar. Neben vollständig neuen Bindemittelsystemen ohne Verwendung von Kalk und CCS/CCU-Technologien zur Vermeidung der CO2-Emissionen bei Verwendung von Kalk, können Abfälle und Nebenprodukte wie etwa Betonbrechsand, verschiedene Schlacken und weitere Massenreststoffe sinnvoll zur Einsparung von Rohstoffen und zur Vermeidung von CO2-Emissionen eingesetzt werden. Es gilt diese Potentiale von Sekundärrohstoffen branchenübergreifend zu identifizieren und Synergien zwischen den Branchen nutzbar zu machen. Hierbei werden neben der chemischen Zusammensetzung der Abfälle und Nebenprodukte auch die Verfügbarkeit und der Massenstrom relevante Kriterien sein. Die potenziellen Sekundärrohstoffe und deren Gemische mit chemisch ähnlicher Zusammensetzung wie die bisher verwendeten Bindemittel, können durch verschiedene technische Ansätze wieder in reaktive Bindemittel umgewandelt und damit nutzbar gemacht werden. Eine gezielte Umwandlung der nicht reaktiven mineralischen Phasen in neue mineralische Phasen mit guten Bindemitteleigenschaften, kann u. a. durch Schmelzprozesse erzielt werden. In Schmelzen können bei hohen Temperaturen die bestehenden, nicht reaktiven mineralischen Phasen zerstört und neue mineralische Phasen mit guten Bindemitteleigenschaften erzeugt werden. Hohe Freiheitsgrade durch gezielte Einstellung der stofflichen Zusammensetzung der Schmelze, durch Stoffseparationen und durch geregelte Abkühlregimes können eine maßgeschneiderte Erzeugung neuer Bindemitteltypen ermöglichen. Aufgrund der hohen erforderlichen Temperaturen von Schmelzprozessen ist die Umsetzung dieser neuen Verfahren nach Möglichkeit in bestehenden pyrometallurgischen Produktionsrouten wie etwa der Stahlproduktion vorzunehmen. So kann etwa der Einsatz von Betonbrechsand als Schlackebildner in der Stahlproduktion zielführend sein, wenn die Schlacke wieder zu einem Bindemittel prozessiert wird und in Zementen Verwendung findet. Eine stoffliche Kreislaufführung wäre hiermit gegeben, wobei der Einsatz von Kalkstein als Schlackebildner oder Rohstoff für die Zementproduktion, und damit die entsprechenden CO2-Emissionen, vermieden werden. Die Entwicklung neuartiger Bindemittelsysteme auf Basis von Sekundärrohstoffen sollte von erforderlichen Anpassungen und neuen Entwicklungen in der Regelsetzung und Normung begleitet werden. Vor allem muss gewährleistet sein, dass die mit neuen Bindemitteln hergestellten Betone den hohen Anforderungen an Dauerhaftigkeit und Umweltverträglichkeit genügen. Des Weiteren sollte mit den etablierten Methoden, wie etwa der Lebenszyklusanalyse, untersucht werden, inwiefern und in welchem Umfang die neuen technischen Entwicklungen zu Nachhaltigkeit und Klimaschutz beitragen.
One of the key elements in the transformation towards a circular economy (CE) is providing more sustainable practices for resources and waste management. Improvement actions focused on transformation towards a CE should be targeted at all groups of materials and waste. As water is essential for human survival and well-being and plays a significant role in sustainable development (SD), the actions related to the reuse of water and the recovery of raw materials from wastewater and other water-based waste should be taken. The paper presents a proposition for a new CE model framework in the water and wastewater sector, which includes the six following actions: reduction—prevent wastewater generation in the first place by the reduction of water usage and pollution reduction at source; reclamation (removal)—an application of effective Technologies for the removal of pollutants from water and wastewater; reuse—reuse of wastewater as an alternative source of water supply (non-potable usage), recycling—recovery of water from wastewater for potable usage; recovery—recovery of resources such as nutrients and energy from water-based waste, and rethink—rethinking how to use resources to create a sustainable economy, which is `free` of waste and emissions. The novelty of the proposed CE model framework is that it presents possible ways of implementing CE principles in the water and wastewater sector, with a strong emphasis not only technological but also organisational and societal changes. Application of the proposed model may help to further transform the European economy to the CE model. Moreover, the indicated model can be significant tool supporting an assessment of local or regional progress towards CE in the water and wastewater sector and further environmental management and planning.
The use of highly water-soluble phosphorus (P) fertilizers can lead to P fixation in the soil, reducing fertilization efficiency. Waste-derived, low water-solubility sources can potentially increase sugarcane’s P uptake compared to triple superphosphate by reducing adsorption to the soil.
Aims:We aimed to test struvite, hazenite, and AshDec® for their agronomic potential as recycled fertilizers for sugarcane production in a typical tropical soil.We hypothesize that these sources can reduce P fixation in the soil, increasing its availability and sugarcane’s absorption.
Methods: In a greenhouse pot experiment, two consecutive sugarcane cycles, 90 days each, were conducted in a Ferralsol. The recovered sources struvite, hazenite, AshDec®, and the conventional triple superphosphate were mixed in the soil in three P doses (30, 60, and 90 mg kg–1), aside a control (nil-P). At both harvests, sugarcane number of sprouts, plant height, stem diameter, dry mass yield, shoot phosphorus, and soil P fractionation were investigated.
Results: At 90 days, struvite and hazenite performed better for dry mass yield (70.7 and 68.3 g pot–1, respectively) than AshDec® and triple superphosphate (59.8 and 57.4 g pot–1, respectively) and for shoot P, with 98.1, 91.6, 75.6, and 66.3 mg pot–1, respectively. At 180 days, struvite outperformed all treatments for dry mass yield (95.3 g pot–1) and AshDec® (75.5 mg pot–1) for shoot P. Struvite was 38% and hazenite 21% more efficient than triple superphosphate in P uptake, while AshDec® was 6% less efficient. Soil had higher labile P under struvite, hazenite, and AshDec® than triple superphosphate by the end of the first cycle, while only the later increased nonlabile P by the end of the experiment (180 days).
Conclusions:Waste-derived P sources were more efficient in supplying P for sugarcane and delivering labile P in 180 days than triple superphosphate.
Bei der Stahlproduktion fallen verfahrensbedingt große Mengen an Nebenprodukten und Abfällen wie Stahlwerksschlacken, Filterstäube und Gichtgasschlämme an. Hohe Anteile dieser Stoffströme werden aufgrund ihrer Zusammensetzung immer noch deponiert, obwohl sie ein hohes Wertstoffpotential aufweisen. An der Bundesanstalt für Materialforschung und -prüfung (BAM) werden Verfahren untersucht
und entwickelt, welche eine Verwertung und Kreislaufführung dieser Materialströme ermöglichen. Aus sogenannten Linz-Donawitz-(LD)-Schlacken können durch carbothermische Nachbehandlung Roheisen und ein dem Portlandzementklinker (PZK) ähnliches Bindemittel erzeugt werden. Aus Elektroofenstäuben und Gichtgasschlämmen kann Zink gewonnen und die Anteile an Eisen und Kohlenstoff in den Stahlproduktionsprozess zurückgeführt werden. Durch diese technischen Maßnahmen kann es gelingen die Deponierung von Abfällen der Stahlproduktion zukünftig deutlich zu reduzieren.
Bei der Stahlproduktion fallen verfahrensbedingt große Mengen an Nebenprodukten und Abfällen wie Stahlwerksschlacken, Filterstäube und Gichtgasschlämme an. Hohe Anteile dieser Stoffströme werden aufgrund ihrer Zusammensetzung immer noch deponiert, obwohl sie ein hohes Wertstoffpotential aufweisen. An der Bundesanstalt für Materialforschung und -prüfung (BAM) werden Verfahren untersucht und entwickelt, welche eine Verwertung und Kreislaufführung dieser Materialströme ermöglichen. Aus sogenannten Linz-Donawitz-(LD)-Schlacken können durch carbothermische Nachbehandlung Roheisen und ein dem Portlandzementklinker (PZK) ähnliches Bindemittel erzeugt werden. Aus Elektroofenstäuben und Gichtgasschlämmen kann Zink gewonnen und die Anteile an Eisen und Kohlenstoff in den Stahlproduktionsprozess zurückgeführt werden. Durch diese technischen Maßnahmen kann es gelingen die Deponierung von Abfällen der Stahlproduktion zukünftig deutlich zu reduzieren.
In Bayern wird Klärschlamm aus der kommunalen Abwasserreinigung weitgehend verbrannt. Monoverbrennungsanlagen - ausschließlich für kommunalen Klärschlamm - gibt es in Altenstadt, München, Gendorf, Straubing, Neu-Ulm und zukünftig auch in Augsburg. Die Anlage in Altenstadt verbrennt jährlich ca. 55.000 t Klärschlamm-Trockensubstanz und produziert dabei rund 15.000 t phosphatreiche Aschen.
Die Asche aus Altenstadt wird zurzeit überwiegend direkt landwirtschaftlich genutzt. Aufgrund der niedrigen Schadstoffgehalte ist diese Nutzung nach den düngemittelrechtlichen Regelungen gesetzlich zulässig. Um der Intention der neuen Düngeverordnung (26. Mai 2017) nach hocheffizienten, d.h. gut pflanzenverfügbaren Düngemitteln zu entsprechen, ist eine Aufbereitung der Klärschlammasche geplant. Im Rahmen des R-Rhenania Projektes errichten der Betreiber der Klärschlammverbrennungsanlage Altenstadt in Bayern Emter GmbH - und der Düngemittelhersteller sePura GmbH gemeinsam eine AshDec®-Demonstrationsanlage, die im Jahr 2023 den Betrieb aufnehmen soll. Das angewandte AshDec®-Verfahren schließt die Phosphate in der Klärschlammasche thermisch im Drehrohrofen auf und macht diese für Pflanzen vollständig verfügbar. Gleichzeitig werden Schadstoffe wie Arsen, Blei und Cadmium entfernt. Den thermischen Aufschluss kennt man bereits vom erfolgreichen, aber nicht mehr produzierten Düngemittel „Rhenania-Phosphat“, das auf der Basis von Rohphosphaten hergestellt wurde.
Die geplante Anlage wird neben den Aschen aus Altenstadt zusätzlich die Aschen aus weiteren bayerischen Verbrennungsanlagen verwerten und für eine Kapazität von 30.000 Jahrestonnen Asche ausgelegt sein. Der Projektpartner sePura plant den produzierten Dünger vollständig in Bayern zu verwerten. Dies verringert die Umweltbelastung durch lange Transportwege und fördert die Regionalität des Vorhabens.
Phosphorus rich sewage sludge ash is a promising source to produce phosphorus recycling fertilizer. However, the low plant availability of phosphorus in these ashes makes a treatment necessary. A thermochemical treatment (800–1000 °C) with alkali additives transforms poorly plant available phosphorus phases to highly plant available calcium alkali Phosphates (Ca,Mg)(Na,K)PO4. In this study, we investigate the use of K2SO4 as additive to produce a phosphorus potassium fertilizer in laboratory-scale experiments (crucible). Pure K2SO4 is not suitable as high reaction temperatures are required due to the high melting point of K2SO4.
To overcome this barrier, we carried out series of experiments with mixtures of K2SO4 and Na2SO4 resulting in a lower economically feasible reaction temperature (900–1000 °C). In this way, the produced phosphorus potassium fertilizers (8.4 wt.% K, 7.6 wt.% P) was highly plant available for phosphorus indicated by complete extractable phosphorus in neutral ammonium citrate solution. The added potassium is, in contrast to sodium, preferably incorporated into silicates instead of phosphorus phases. Thus, the highly extractable phase (Ca,Mg)(Na,K)PO4 in the thermochemical products contain less potassium than expected. This preferred incorporation is confirmed by a pilot-scale trial (rotary kiln) and thermodynamic calculation.
Conventional phosphate fertilizers are usually highly water-soluble and rapidly solubilize when moistened by the soil solution. However, if this solubilization is not in alignment with plants demand, P can react with the soil colloidal phase, becoming less available over time. This is more pronounced in acidic, oxidic tropical soils, with
high P adsorption capacity, reducing the efficiency of P fertilization. Furthermore, these fertilizers are derived from phosphate rock, a non-renewable resource, generating an environmental impact. To assess these concerns, waste-recycled P sources (struvite, hazenite and AshDec®) were studied for their potential of reducing P Fixation by the soil and improving the agronomic efficiency of the P fertilization. In our work, we compared the solubilization dynamics of struvite, hazenite, AshDec® to triple superphosphate (TSP) in a sandy clay loam Ferralsol, as well as their effect on solution pH and on soil P pools (labile, moderately-labile and non-labile) via an incubation experiment. Leaching columns containing 50 g of soil with surface application of 100 mg per column (mg col 1) of P from each selected fertilizer and one control (nil-P) were evaluated for 60 days. Daily leachate samples from the column were analyzed for P content and pH. Soil was stratified in the end and submitted to P
fractionation. All results were analyzed considering p < 0.05. Our findings showed that TSP and struvite promoted an acid P release reaction (reaching pHs of 4.3 and 5.5 respectively), while AshDec® and hazenite reaction was alkaline (reaching pHs of 8.4 and 8.5 respectively). Furthermore, TSP promoted the highest P release among all sources in 60 days (52.8 mg col 1) and showed rapid release dynamic in the beginning, while struvite and hazenite showed late release dynamics and lower total leached P (29.7 and 15.5 mg col 1 P respectively). In contrast, no P-release was detected in the leachate of the AshDec® over the whole trial period. Struvite promoted
the highest soil labile P concentration (7938 mg kg 1), followed by hazenite (5877 mg kg 1) and AshDec® (4468 mg kg 1), all higher than TSP (3821 mg kg 1), while AshDec® showed high moderately-labile P (9214 mg kg 1), reaffirming its delayed release potential.
Future nutrient recovery from sewage sludge regarding three different scenarios - German case study
(2022)
Agricultural sewage sludge utilization becomes less important in Germany. In 2017, new fertilizer and waste laws caused the agricultural sewage sludge utilization to collapse by more than a quarter. From 2029, German wastewater treatment plants (WWTPs) must recover phosphorus (P) from sewage sludge if it contains more than 2 wt % P. Agricultural utilization will be prohibited for large WWTPs >100,000 population equivalents (pe) from 2029 and >50,000 pe from 2032. In Germany, each federal state must annually report amounts and quality of agriculturally utilized sewage sludge which was 16% of the total disposal in 2019. The reports of 10 states were evaluated for 2016 and 2017 representing approx. 60% of the total agriculturally used sludge volume. In 2016, 60% of the WWTPs’ sludges exceeded the recovery limit of 2 wt % P which is 70% of the amount of sludge and 85% of the phosphorus load. Other nutrients are not affected by the recovery obligation. However, many P recovery processes recover other nutrients, too. Considering three different scenarios for future German sewage sludge disposal shows that 70–77% of the P load in sewage sludge will probably be recovered in the future. At the same time, this applies for about 0–16% nitrogen, 36–52% of calcium, 31–53% of potassium, and 40–52% of magnesium. However, these recovered nutrients loads can substitute only 1% or less of the commercial fertilizer demand except from phosphorus which is up to 43% of the demand.
Agricultural sewage sludge utilization becomes less important in Germany. In 2017, new fertilizer and waste laws caused the agricultural sewage sludge utilization to collapse by more than a quarter. From 2029, in German wastewater treatment plants (WWTPs) phosphorus (P) must be recovered from sewage sludge ifit contains more than 2 wt % P. Agricultural utilization will be prohibited for large WWTPs > 100,000 population equivalents (pe) from 2029 and > 50,000 pe from 2032. In Germany, each federal state must annually report amounts and quality of agriculturally utilized sewage sludge which was 17 % of the total disposal in 2019. The reports of 10 States were evaluated for 2016 and 2017 representing approx. 60 % ofthe total agriculturally used sludge volume. Whereas phosphorus recovery is mandatory this does not apply to other nutrients. However, many P recovery processes recover other nutrients, too.
Considering three differentscenariosfor future German sewage sludge disposal Shows that 70 - 77 % ofthe P load in sewage sludge will probably be recovered in the future.
At the same time, this applies for about 0 - 16 % of nitrogen, 36 - 52 % of calcium, 31-53 % of potassium, and 40 - 52 % of magnesium. However, these recovered nutrient loads can substitute only 1 % or less ofthe commercial fertilizer demand except from phosphorus which is about 45 % ofthe demand.
Gypsum is widely used in the construction sector and its worldwide consumption has been increasing for several decades. Depending on the life-time of the used gypsum products, an increase of gypsum in construction and demolition waste follows. Especially against the background of a circular economy, the recycling of waste gypsum is of growing importance. However, the use of recycled gypsum makes only sense if it is environmentally friendly. Therefore, an evaluation of the environmental impacts of an industrial-scale processing for the recycling of post-consumer gypsum waste was conducted. The evaluation was performed with an established life cycle assessment software. Original data provided by industry and complementary data from a database for life cycle assessments were used for the calculations. Two scenarios for recycled gypsum with different transportation distances were calculated. These results are compared with results of the environmental evaluation of gypsum derived from coal-fired power plants (FGD gypsum) and natural gypsum. The results show that utilization of recycled gypsum can be environmentally advantageous compared to the use of natural gypsum or FGD gypsum, especially in the impact categories land transformation and resource consumption (abiotic depletion potential). For most environmental impact categories the specific transportation distances have a strong influence.
Recycled fertilizers produced using processes for the recovery of phosphate from residual materials such as wastewater, sewage sludge and sewage sludge ashes show very good bioavailability, but it is still a product largely unknown to the market. The aim of CLOOP is therefore to document the properties and effects of such fertilizers through chemical, mineralogical and ecological analyses as well as analytical method development and pot and field plant growth trials.
Outotec focused on 3 points in CLOOP: Experimental campaigns, process simulations as well as economic analyses with focus on the AshDec process, respectively the design of a large-scale AshDec plant for phosphorus recovery. The laboratory scale trials as well as the semi-industrial scale campaign provided valuable insights into the operating parameters of the process and the plant. As a result, for example, the temperature range could be significantly lowered, and the additive addition reduced by approx. 20 %. They have further shown that the AshDec process is not susceptible to operating fluctuations and that the product can be consistently produced at high quality. With the selection of suitable operating parameters, heavy metals (As, Pb, Cd, (Zn)) can be removed. Within the campaign, about 1.5 t of fertilizer for the plant trials in CLOOP could be produced. An AshDec plant process was digitally created in simulation software, allowing valuable process parameters to be simulated at various operating parameters. On this basis, a full-scale plant was designed. The data obtained in the project were used for a detailed economic analysis including a sensitivity analysis. It was possible to show under which conditions this plant can be operated economically.
At BAM, the AshDec fertilizer was synthesized with different additives and then applied to plant experiments at Uni Bonn. The goal hereby was to check differences in plant uptake. Because of the promising results of AshDec synthesized with sodium-carbonate and because this AshDec version does not require special off gas treatment for sulfur recovery (compared to AshDec synthesized with sodium-sulfate), all project partners agreed on continuing working with this AshDec variation. It was then used as a raw P-source for formulating it into NPK-fertilizers, by granulation with ammonium-sulfate and straw ash as potassium source. These recycling fertilizers were applied to plant- and field experiments by project partners in Brazil (University of Sao Paulo) and Australia (University of Queensland). Furthermore, in leaching experiments, the solubility of phosphorus in AshDec was compared to triple super phosphate. The experiments were carried out on soils with a varying phosphorus buffering index. Results show, that the phosphorus form in AshDec is way less soluble in water. This indicates that AshDec has the potential for a so-called next generation fertilizer – a fertilizer which’s nutrients remain in the soil and supply the plant according to its needs. At the moment, this behavior gets examined more in depth in lysimeter experiments in cooperation with University of Technology Berlin.
The focus of KWB is the Life Cycle Assessment (LCA) of different NextGen fertilizers to evaluate the entire process chain from recovery to fertilizer application. The NextGen fertilizer is credited by the amount of plant available nutrients in the product, which replace nutrients from conventional fertilizer. The LCA covers N-struvite precipitation from municipal wastewater, K-struvite precipitation from industrial wastewater and the AshDec-product from sewage sludge. The LCA task is almost complete. It could be shown that struvite precipitation has comprehensive environmental benefits, mainly since positive side effects occur in sewage sludge treatment (e.g. reduced sludge volume). In principle, the energetic and ecological profile of the AshDec process compared to direct use of sewage sludge ash cannot be assessed as being generally beneficial or negative. Regarding the global warming potential, the Ashdec process shows that the expenses (e.g. energy, chemicals) cannot be covered by the P fertilizer credit. In contrast, the impact categories “terrestrial acidification potential”, and “freshwater eutrophication potential” show positive results as the credits for conventional fertilizer are higher than the burdens for the process.
At University Bonn, the standardized pot experiments were conducted with several AshDec variations, using ryegrass, soybean, and spinach on a slightly acidic sandy soil and an organic-free standard substrate. P-uptake and biomass production of different AshDec variations were generally like those of triple super phosphate and struvite, and clearly outperformed untreated sewage sludge ash and rock phosphate. Field trials in Australia and Brazil with sugarcane on acidic soils are still ongoing and results are expected by the end of 2021.
Verwertung von Klärschlamm
(2018)
Die natürlichen Nährstoffkreisläufe werden durch anthropogene Einflüsse, wie das Einbringen von Schadstoffen in nährstoffreiche Stoffströme, und die ungünstige lokale Verteilung der Nährstoffe (z.B. im Zuge der Intensivtierhaltung), erheblich gestört. Es sind lokale Unter- und Überversorgungen mit Nährstoffen zu beobachten. Gelangen die Nährstoffe in Gewässer, kommt es zum bekannten Phänomen der Eutrophierung. Hierbei ist der Nährstoff Phosphat meist der limitierende Faktor und es bestehen große Bestrebungen den anthropogenen Eintrag in Fließgewässer, Seen und Binnenmeere zu unterbinden. Der Schutz der Ostsee vor Nährstoffeinträgen ist beispielsweise ein sehr wichtiges Thema geworden und wird u.a. von der Baltic Sea Action Group verfolgt.
Weitere Auswirkungen des bestehenden Systems sind Entzüge aus dem Nährstoffkreislauf, wie etwa bei der Deponierung phosphor- aber gleichzeitig auch schadstoffhaltiger Klärschlammaschen oder bei der Mitverbrennung von Klärschlamm in Müllverbrennungsanlagen, Kraftwerken oder Zementwerken. Hier wird das Phosphat ebenfalls als Bestandteil von Aschen deponiert oder in Form von Baustoffen einer sinnvollen stofflichen Nutzung entzogen. Gegen diese Art des Verlusts von Phosphat aus dem Nährstoffkreislauf hat der Gesetzgeber mit der Novellierung der Klärschlammverordnung reagiert, die am 3. Oktober 2017 in Kraft getreten ist und u.a. Regelungen zur Rückgewinnung von Phosphat aus Klärschlamm und Klärschlammasche enthält.
Klärschlämme aus kommunalen Abwasserbehandlungsanlagen ab einer genehmigtenAusbaugröße von über 100.000 bzw. über 50.000 Einwohnerwerten (EW) dürfen nach einer Übergangsfrist ab dem 1. Januar 2029 bzw. 2032 nicht mehr in der Landwirtschaft oder im Landschaftsbau verwertet werden. Die Betreiber dieser Anlagen sind zur Rückgewinnung des im Schlamm enthaltenen Phosphors verpflichtet, wenn der Klärschlamm einen Phosphorgehalt von 20 g/kg Trockenrückstand (TR) oder mehr aufweist. Für Klärschlämme mit P-Gehalten > 40 g/kg TR reicht alternativ die Absenkung der P-Konzentration um 50 % aus. Die Rückgewinnung kann aus dem Schlamm oder aus der Verbrennungsasche des thermisch vorbehandelten Klärschlamms erfolgen.
Aus der Asche müssen mindestens 80 % des Phosphoranteils zurückgewonnen werden. Anstelle einer Phosphorrückgewinnung aus Klärschlämmen aus kleineren und mittelgroßen Abwasserbehandlungsanlagen (bis 50.000 EW) können diese Schlämme auch
weiterhin zu Düngezwecken auf Böden ausgebracht werden, sofern die Anforderungen und insbesondere die Grenzwerte der Klärschlammverordnung und des Düngerechts eingehalten werden.
In der Abwasserreinigung wird der Makronährstoff Phosphor je nach Typ und Größe der Abwasserreinigungsanlage durch verschiedene Verfahren der Phosphatelimination weitgehend in die feste Phase, den Klärschlamm, überführt. Dies geschieht durch die Zugabe von Fällmitteln auf der Basis von Eisen- oder Aluminiumsalzen, oder durch das Verfahren der vermehrten biologischen Phosphorelimination (Bio-P). Das Phosphat liegt nun abhängig vom eingesetzten Verfahren als Bestandteil der gewachsenen Biomasse, als gefälltes Salz, adsorbiert an Eisen(oxi)hydroxiden oder im Falle der Bio-P Klärschlämme auch intrazellulär in Form von Polyphosphaten vor. Weitergehende Informationen hierzu sind im Beitrag von Kratz et al. Pflanzenverfügbarkeit und agronomische Effizienz von klärschlamm-basierten Phosphor (P) – Recyclingdüngern in diesem Buch zu finden. Die Bindungsformen unterscheiden sich demnach nach Art der eingesetzten Technologie der Phosphatelimination erheblich und haben einen entscheidenden Einfluss auf die verschiedenen Möglichkeiten der P-Extraktion und Rückgewinnung.
Herstellung neuer Düngemittelausgangsstoffe durch thermochemische Behandlung von Klärschlammaschen
(2018)
Klärschlammasche kann viel Phosphor enthalten (bis zu 12%). Aus diesem Grund ist diese Asche ein gutes Ausgangsmaterial für Phosphordünger. Aufgrund der geringen Pflanzenverfügbarkeit des Phosphors in der Asche ist eine Aufbereitung notwendig.
In diesem Buchbeitrag wird das thermochemische Verfahren AshDec vorgestellt, welches von dem Fachbereich 4.4 mit der Firma Outotec entwickelt worden ist. Es werden die Hintergründe diskutiert, die Phasenreaktionen bei diesem Prozess besprochen, Pflanzenversuche ausgewertet, verschiedene Extraktionen diskutiert und ein Konzept für eine mögliche Pilotanlage dargestellt.
Advantages of recycling gypsum plaster boards
During the last decades the material composition of buildings has become increasingly diverse. However, largely sorted material flows are needed for generating high quality secondary building materials. The use of secondary building materials can meet the requirements of sustainability in several ways: the extended time availability of primary raw materials and, thereby, the preservation of natural resources as well as the conservation of landfill sites.
Recycling of gypsum (calcium sulfate) can be a good example for the environmental benefits of closed-loop recycling. The content of sulfates in other secondary building materials, in particular in recycled concrete aggregates, should be minimized for quality reasons. In contrast, separated gypsum can also be used in gypsum production if the high quality requirements for the recycled gypsum are met. Since almost all processing steps in the recycling process are associated with environmental impacts, an environmental evaluation of the use of recycled gypsum as a substitute in gypsum production has to be carefully conducted.
This paper focusses on the techniques for generating recycled gypsum from gypsum plasterboards, the related quality requirements and a comprehensive environmental evaluation of the complete process.
During the last decades the material composition of buildings has become increasingly diverse. However, largely sorted material flows are needed for generating high quality secondary building materials. The use of secondary building materials can meet the requirements of sustainability in several ways: the extended time availability of primary raw materials and, thereby, the preservation of natural resources as well as the conservation of landfill sites.
Recycling of gypsum (calcium sulfate) can be a good example for the environmental benefits of closed-loop recycling. The content of sulfates in other secondary building materials, in particular in recycled concrete aggregates, should be minimized for quality reasons. In contrast, separated gypsum can also be used in gypsum production if the high quality requirements for the recycled gypsum are met. Since almost all processing steps in the recycling process are associated with environmental impacts, an environmental evaluation of the use of recycled gypsum as a substitute in gypsum production has to be carefully conducted.
This paper focusses on the techniques for generating recycled gypsum from gypsum plasterboards, the related quality requirements and a comprehensive environmental evaluation of the complete process.
Since the recycling of tantalum bearing post-consumer waste is practically not existent, metallurgical residues are the most important feed for the tantalum recycling. Most tin ores naturally contain significant quantities of refractory metals. During the smelting process in primary tin production these elements are enriched in the slag phase. This slag is a highly valuable raw material for tantalum production due to its considerable concentration of tantalum and its functioning as an additional slag former in further pyrometallurgical treatment.
In this paper the first process stage of an existing pyrometallurgical process for tantalum recovery, mainly from low grade pyrometallurgical residues, is discussed. Smelting trials were carried out in a pilot-scale electric arc furnace to analyse the effect of feeding on the activity of carbon as a reducing agent. Therefore, blowing petroleum coke through an iron lance and the manual adding of coke into the melting bath were tested. During the pyrometallurgical treatment elements with a high affinity to carbon were reduced to their carbide form and enriched in the molten iron-based metal phase. The objective of the process was to reduce the oxidic tantalum completely and to enrich it into the metal phase. Furthermore, the transfer of unwanted elements such as titanium into the metal phase was aimed to be avoided.
Spoon test specimens were taken from the liquid mineral melt to follow the evolution of the reduction process. The cooled down solidified melting bath was investigated by using the XRD and EDX method to characterise the slag system and to identify relevant mineral phases.
Blast furnace (BF) sludge and electric arc furnace (EAF) dust are typical wastes that incur from iron and steel production. In addition to iron, calcium, carbon, and silicon they usually contain high concentrations of heavy metals such as zinc, lead, and cadmium that are potentially hazardous to the environment, rendering disposal in landfills ecologically problematic and costly. Consequently, pyrometallurgical, hydrometallurgical, and hybrid methods for selective elimination of non-ferrous heavy metals from BF sludge and EAF dust have been conceived, of which only the carbothermic reduction route taken in the so-called Waelz rotary kiln process has been proven to be economically successful. However, this process has several drawbacks regarding efficiency of heavy-metal removal and recovery of iron, and it does not allow processing of BF sludge. In this study, we investigated the efficiency and feasibility of selective chlorination and evaporation of non-ferrous heavy metals, particularly zinc and lead, in both BF sludge and EAF dust as an alternative, thermochemical processing route. To this end, hydrochloric acid and iron(II) chloride solution have been used as chlorinating agents, and the process of heavy-metal chlorination and evaporation has been investigated under inert operating conditions, at variable chlorine concentrations, and at temperatures between 500 and 1200 °C.
High zinc and lead removal efficiencies of > 99.5 % were achieved with both chlorinating agents, but iron(II) chloride turned out to be overall more efficient for removal of zinc and lead from BF sludge and EAF dust. Interestingly, and in contrast to previous studies, the iron was completely retained in the processed solid residue, therefore rendering the processed residues virtually zinc- and lead-free raw materials that may either be used internally (e.g., feeding processed BF sludge and EAF dust back into the respective furnaces) or externally (e.g., for cement production).
An existing pyrometallurgical process for tantalum and niobium recovery, mainly from low grade pyrometallurgical residues, was investigated. Series of melting experiments were carried out in a pilot-scale electric arc furnace to study how the amount, the grain size and the way of feeding affect the activity of carbon as a reducing agent. During the pyrometallurgical treatment refractory metals such as tantalum and niobium are reduced to their carbide form and enriched in the molten iron-based metal phase. The cooled down slag and metal phase were analysed to investigate thermodynamic and kinetic conditions of the carbide formation. FACT Sage simulations were also used to investigate the material system in state of thermodynamic equilibrium. Results show that mass transfer and kinetics may play an important role if compared to equilibrium analyses using FACT Sage.