Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (18) (entfernen)
Schlagworte
- Betatron (3)
- Image quality (3)
- Radar (3)
- Zerstörungsfreie Prüfung (3)
- Baudenkmäler (2)
- Container inspection (2)
- Digital detector array (DDA) (2)
- Digital radiography (2)
- High-energy X-ray imaging (2)
- NDT (2)
Organisationseinheit der BAM
Muon Tomography of the Interior of a Reinforced Concrete Block: First Experimental Proof of Concept
(2021)
Quality assurance and condition assessment of concrete structures is an important topic world-wide due to the aging infrastructure and increasing traffic demands. Common topics include, but are not limited to, localisation of rebar or tendon ducts, geometrical irregularities, cracks, voids, honeycombing or other flaws. Non-destructive techniques such as ultrasound or radar have found regular, successful practical application but sometimes suffer from limited resolution and accuracy, imaging artefacts or restrictions in detecting certain features. Until the 1980s X-ray transmission was used in case of special demands and showed a much better resolution than other NDT techniques. However, due to safety concerns and cost issues, this method is almost never used anymore. Muon tomography has received much attention recently. Novel detectors for cosmic muons and tomographic imaging algorithms have opened up new fields of application, such as the investigation of freight containers. Muon imaging also has the potential to fill some of the gaps currently existing in concrete NDT. As a first step towards practical use and as a proof of concept we used an existing system to image the interior of a reference reinforced 600 kg concrete block. Even with a yet not optimized setup for this kind of investigation, the muon imaging results are at least of similar quality compared to ultrasonic and radar imaging, potentially even better. The data acquisition takes more time and signals contain more noise, but the images allowed to detect the same important features that are visible in conventional high energy X-ray tomography. In our experiment, we have shown that muon imaging has potential for concrete inspection. The next steps include the development of mobile detectors and optimising acquisition and imaging parameters.
Digital detectors such as phosphor imaging plates (IP) and digital detector arrays (DDA) enable radiographic inspection with higher efficiency and improved image quality in comparison to the classic film technique. The mobile mechanised tomographic system TomoCAR (tomographic computer aided radiology) was developed first for inspection of circumferential welded seams of pipes. It consists of the manipulator based position control of an X-ray tube in front of the region to inspect and a digital detector array behind it. The high contrast sensitivity technique was combined with planar tomography. The tomographic reconstruction allows the three-dimensional (3D) representation of the material structure and included defects, equivalent to a metallographic cross sectioning. The hardware design is based on a specially developed flat X-ray tube and a direct converting CMOS detector array on CdTe basis. TomoCAR is applied for sizing of volumetric and planar defects. It allows the reliable detection of planar defects with openings larger than 25µm by subpixel resolution due to the achieved high signal-to-noise ratio. TomoCAR was successfully qualified as the result of a German pilot study on the basis of the European Network of Inspection and Qualification (ENIQ) guidelines for application in the nuclear power industry. Application examples are presented. The TomoCAR design was modified for in situ inspection of large aircraft components under production conditions. A gantry gate based planar tomograph was constructed and tested for inspection of the integrity of large flat CFRP panel components of up to 3 m × 9 m size. The integrity of imbedded stringers has been successfully observed. Different trials were performed to prove the finding rate of cracks in embedded stringers, which will be presented and discussed.
A comparative study on the performance of digital detector systems for high energy applications
(2014)
For cast components reaching or exceeding total material thicknesses of 150mm, high energy sources such as linear accelerators or Betatrons are required in order to obtain reasonable exposure times. In this study, the performance of digital detector systems, involving imaging plates (IP) and digital detector arrays (DDA), was evaluated with respect to the testing class B requirements as formulated in the standard EN ISO 17636-2. As a reference, traditional radiographic film and a Cobalt-60 source was used. With film exposures, testing class B was achieved with Co-60 and Betatron (7.5 MV) at longer exposure times. The preliminary results show that the testing class B was not obtained with the examined digital detector arrays (DDA) and the high resolution imaging plates (IP) , even at 40, 60 and 80 minutes exposure time with a 7.5 MV Betatron. Class A was achieved using high resolution imaging plates with optimized metal filters between object and IPs and a high resolution DDA with intermediate Cu filters. Class A was also achieved applying a DDA with lower basic spatial resolution than required by Table B.13 of EN ISO 17636-2, but using the compensation principle as described in this standard. The next generation of digital detector arrays might potentially be able to obtain class B performance with the expected spatial resolution and sensitivity improvements.
The progress in X-ray detector electronics (sensitivity and speed) allows meanwhile fast single photon detection by a matrix detector. Combined photon counting and energy discrimination is implemented in the electronic circuit of each detector pixel. The company XCounter developed detectors based on CdTe single crystals, which can be tiled to larger areas and have a pixel size of 100ìm. The largest area available in beginning of 2014 is 50x75 mm². These detectors have very promising properties, which make them very suitable for NDT applications:
1. A CdTe attenuation layer of 750 µm thickness allows efficient X-ray detection up to ca. 300 keV. In counting mode only photon noise is important; no other detector noise sources need to be considered. There is no Offset signal without radiation.
2. Each of the detector pixels has two energy thresholds. These can be used for dual energy imaging for materials separation. Also the suppression of scattered radiation by energy thresholding will improve the image contrast sensitivity. First experiments will be presented which demonstrate the advantages of this new detector technology over the conventional charge integrating detectors.
A challenge is the development of a modified detector calibration procedure, which becomes critical at longer exposure times.