Filtern
Dokumenttyp
- Vortrag (3)
- Zeitschriftenartikel (1)
- Beitrag zu einem Tagungsband (1)
Sprache
- Englisch (5)
Schlagworte
- Constitutive law (5) (entfernen)
Eingeladener Vortrag
- nein (3)
Experimental characterization and mechanical modeling of creep induced rafting in superalloys
(2012)
A constitutive model has been developed for the high temperature mechanical behavior of single crystal superalloys, including rafting and its consequences. The flow stress depends on the γ channel width via the Orowan stress. An evolution equation for channel widening during high temperature straining has been derived and calibrated with measurements. Therein, rafting is assumed to be driven by the relaxation of internal stresses. The model is able to represent the mechanical softening at high stresses consecutive to rafting. The model has been applied to simulate rafting during uniaxial creep in several crystal orientations, in notched specimens as well as in cyclically loaded specimens.
Under cyclic thermomechanical loading, various effects such as strain accumulation, creep damage, ageing, fatigue etc. may occur in the material of a gas turbine blade. Depending on the loading conditions, all these effects contribute to reduce the lifetime of the component.
Subject of the present work is the development of a material model to describe the mechanical effects mentioned above and to subsequently predict lifetimes by using simulated stress strain data.
Starting point for deformation modeling is the well known viscoplastic model after Chaboche, which provides descriptions of isotropic and kinematic hardening, as well as dynamic and static recovery. The evolution equation for kinematic hardening model has been modified following the proposal of Ohno/Wang to better predict stress controlled cyclic strain accumulation, i.e. ratchetting. A damage variable has been included to represent tertiary creep according to the concept of Kachanov. Finally, the static recovery has been modified following Kindrachuk to account for strain induced ageing. The models parameters have been calibrated using isothermal test data only. The constitutive model has been validated by comparing experimental with predicted TMF stress-strain hystereses.
Lifetime prediction is done with the TMF lifetime model proposed by Riedel. The model assumes that fatigue life is controlled by the propagation of short cracks. Besides pure fatigue, it takes the local creep deformations at the crack tip into account. The model is applied to a broad variety of isothermal and non isothermal tests over temperatures up to 950°C and different loading conditions. The evaluation shows that throughout satisfying results can be achieved using a limited number of model parameters for the whole test data base.
The technological importance, the regularity of the microstructure and the complexity of the mechanical behavior of single crystal superalloys have motivated the development of a large number of mathematical models of the mechanical behavior of these alloys in the last two decades. While crystal viscoplasticity has proven to be an efficient framework to account for their anisotropy, several issues are still challenging. Indeed, most models consider that octahedral and cubic slip systems contribute to the largest part of the plastic deformation. However, the exact nature of cubic slip is still controversial and the precipitates can be sheared by <112> slip systems at intermediate temperatures, which largely influence the dependence of the flow rate on the orientation under creep conditions. Due to the different strengths of the matrix and the precipitates and the large volume fraction of the precipitate phase, a complex distribution of internal stresses exists, which can difficultly be captured by the conventional back stress models of plasticity. In addition, at high temperature, the microstructure degrades and the residual mechanical strength is reduced. The driving force for this microstructure degradation is intimately connected to the distribution of the internal stresses. As a result of this complexity, a large number of tests are usually required to fully characterize the mechanical behavior of single crystal superalloys. This in turn largely impedes the implementation of inelastic modeling in the industrial praxis.
The lecture summarizes the principal types of constitutive models for single crystal superalloys and reviews some recent advances in this area. In particular, it is shown how simulations at the microstructure scale level combined with conventional testing and microscopic analysis helped to improve our understanding of the mechanical behavior of single crystal superalloys. Directional coarsening, the importance of internal stresses, orientation dependency and the corresponding modeling issues are discussed. Also open questions are highlighted.
Gas turbines are widely used for a variety of purposes including power generation, compression or as jet engines in aircrafts. The critical components of a gas turbine are the high-pressure turbine blades which operate under severe conditions. These include thermo-mechanical loadings over temperatures ranging from room temperature up to 1100°C.
While a large number of constitutive models for single crystals have been proposed, most applications are restricted to special loading scenarios, temperature range and deformation mechanisms. In particular, a number of models are focused on pure creep. Only a few papers consider application of both creep and fatigue. Applications of the constitutive models to long-term stress relaxation are even scarcer. The new model assumes deformation-induced softening and can properly reproduce the viscous behavior at different time scales.
The model has been calibrated with the uniaxial tests at 800°C and 950°C in [001], [011] and [111] specimens of a nickel-basis superalloy. The predicted creep, short- and long-term relaxation and cyclic tests are in reasonable agreement with the experimental observations.
Gas turbines are widely used for a variety of purposes including power generation, compression or as jet engines in aircrafts. The critical components of a gas turbine are the high-pressure turbine blades which operate under severe conditions. These include thermo-mechanical loadings over temperatures ranging from room temperature up to 1100°C.
While a large number of constitutive models for single crystals have been proposed, most applications are restricted to special loading scenarios, temperature range and deformation mechanisms. In particular, a number of models are focused on pure creep. Only a few papers consider application of both creep and fatigue. Applications of the constitutive models to long-term stress relaxation are even scarcer. The new model assumes deformation-induced softening and can properly reproduce the viscous behavior at different time scales.
The model has been calibrated with the uniaxial tests at 800°C and 950°C in [001], [011] and [111] specimens of a nickel-basis superalloy. The predicted creep, short- and long-term relaxation and cyclic tests are in reasonable agreement with the experimental observations.