Filtern
Erscheinungsjahr
Dokumenttyp
Schlagworte
- Laser beam welding (58) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (7)
Numerical simulation of electromagnetic melt control systems in high power laser beam welding
(2013)
The availability of laser sources with a power of
20 kW upwards prepared the ground for laser beam
welding of up to 20 mm thick metal parts. Challenges
are the prevention of gravity-driven melt drop-out and
the control of the dynamics mainly due to the
Marangoni flow.
Coupled numerical turbulent fluid flow, thermal and
electromagnetic simulations and experimental
validation with aluminum AlMg3 and stainless steel
AISI 304 were done for alternating and steady
magnetic fields perpendicular to the process direction.
The first can prevent melt sagging in full-penetration
welding by Lorentz forces in the melt induced by an
AC magnet located below the weld specimen
counteracting gravitational forces. The latter controls
the Marangoni flow by Lorentz braking forces in the
melt by the so-called Hartmann effect.
The simulations show that the drop-out of aluminum
and stainless steel can be avoided for 20 mm thick fullpenetration
welds with moderate magnetic flux
densities of 70 mT and 95 mT at oscillation
frequencies of 450 Hz and 3 kHz, respectively. The
experiments are in good agreement but show
somewhat larger values for steel, whose weakly
ferromagnetic properties are a possible reason. The
investigations with steady magnetic fields reveal the
possibility to mitigate the dynamics significantly
beginning with around 500 mT at laser penetration
depths of approximately 20 mm.
The objective of this study was to investigate the influence of externally applied magnetic fields on the weld quality in laser beam welding. The optimization of the process parameters was performed using the results of computer simulations. Welding tests were performed with up to 20 kW laser beam power. It was shown that the AC magnet with 3 kW power supply allows for a prevention of the gravity drop-out for full penetration welding of 20 mm thick stainless steel plates. For partial penetration welding it was shown that an0.5 T DC magnetic field is enough for a suppression of convective flows in the weld pool. Partial penetration welding tests with 4 kW beam power showed that the application of AC magnetic fields can reduce weld porosity by a factor of 10 compared to the reference joints. The weld surface roughness was improved by 50%.
Welding is one of the most critical operations for the construction of reliable metal structures in everything from ships to reactor vessels. When welds fail, the entire structure often fails—so expectations on weld quality have never been higher. Any process that uses a localized heat source, such as welding, is likely to result in some distortion. The welding process of very thick metal components is not inherently stable and is barely controllable without external forces.
Full penetration high power bead-on-plate laser beam welding tests of up to 20 mm thick 2205 duplex steel plates were performed in PA position. A contactless inductive electromagnetic (EM) weld pool support system was used to prevent gravity drop-out of the melt. Welding experiments with 15 mm thick plates were carried out using IPG fiber laser YLR 20000 and Yb:YAG thin disk laser TruDisk 16002. The laser power needed to achieve a full penetration was found to be 10.9 and 8.56 kW for welding velocity of 1.0 and 0.5 m min−1, respectively. Reference welds without weld pool support demonstrate excessive root sag. The optimal value of the alternating current(AC) power needed to completely compensate the sagging on the root side was found to be ≈1.6 kW for both values of the welding velocity. The same EM weld pool support system was used in welding tests with 20 mm thick plates. The laser beam power (TRUMPF Yb:YAG thin disk laser TruDisk 16002) needed to reach a full penetration for 0.5 m min−1 was found to be 13.9 kW. Full penetration welding without EM weld pool support is not possible—the surface tension cannot stop the gravity drop-out of the melt. The AC power needed to completely compensate the gravity was found to be 2 kW.
Full penetration high power bead-on-plate laser beam welding tests of up to 20 mm thick 2205 duplex steel plates were performed in PA position. A contactless inductive electromagnetic (EM) weld pool support system was used to prevent gravity drop-out of the melt. Welding experiments with 15 mm thick plates were carried out using IPG fiber laser YLR 20000 and Yb:YAG thin disk laser TruDisk 16002. The laser power needed to achieve a full penetration was found to be 10.9 and 8.56kW for welding velocity of 1.0 and 0.5 m min(-1), respectively. Reference welds without weld pool support demonstrate excessive root sag. The optimal value of the alternating current (AC) power needed to completely compensate the sagging on the root side was found to be approximate to 1.6 kW for both values of the welding velocity. The same EM weld pool support system was used in welding tests with 20 mm thick plates. The laser beam power (TRUMPF Yb:YAG thin disk laser TruDisk 16002) needed to reach a full penetration for 0.5 m min(-1) was found to be 13.9 kW. Full penetration welding without EM weld pool support is not possible-the surface tension cannot stop the gravity drop-out of the melt. The AC power needed to completely compensate the gravity was found to be 2 kW. (C) 2016 Laser Institute of America