Filtern
Erscheinungsjahr
- 2016 (9) (entfernen)
Dokumenttyp
Schlagworte
- Concrete (3)
- Fatigue (3)
- Damage evolution (2)
- High-cycle (2)
- Admixtures (1)
- Analysis (1)
- Bauwerke (1)
- Concrete damage (1)
- Damage Evolution (1)
- Fire (1)
The current knowledge about fatigue behavior of concrete is still incomplete. This concerns especially the progress of fatigue which precedes the fatigue failure. Therefore, the process of fatigue itself under cyclic compressive loading was investigated in a systematic and comprehensive way. The aim of this investigation was to obtain a deeper insight and to provide a better understanding of the damage process occurring within the material during fatigue loading. Concrete cylinders were tested with a number of cycles to failure between 106 and 107. To investigate macroscopic and microscopic changes in the material, various methods of non-destructive and destructive testing were used. One main result was, in contrast to other authors, that the investigated changes in macroscopic material behavior could not be explained only by a development of micro-cracks. The results indicated rather, that the related changes in the fatigue behavior are mainly a result of viscous processes in the hardened cement paste, similar to the processes of creep. Based on the experimental results a description of the possible processes was derived which take place in the material structure during fatigue loading and also leads to the observed macroscopic changes in the material behavior. In this context, the results have shown that in case of isotropic material behavior a stiffness reduction related to a scalar value could not capture the damage effect on the stress-strain-relationship caused by fatigue.
Self-compacting concrete typically contains a higher content of powder materials than normal concrete. Furthermore it is assumed that the use of superplasticizers yields a more homogenous microstructure in the hardened paste. Both aspects generate a very dense microstructure, which can be assumed to cause material behaviour that differs from than normal concrete when it is exposed to elevated temperatures. However, the paste volumes in SCC can vary significantly based on the mixture composition. At a low paste volumes SCC can be very similar to normal concrete at hardened state while it can vary greatly at higher paste volumes. Since the high temperature behaviour of concrete is strongly affected by the different physical behaviour of the paste and the aggregates, it is likely that the high temperature behaviour is consequently strongly affected by the ratio of these mixture components. In the present study different SCC mixtures were observed with similar mechanical properties, but with significantly differing paste to aggregate ratios. Based on observations of the heat evolution at the fire exposed surface and at different depths inside the specimens as well as based on photogrammetric observations of the spalled dimensions, the results indicate that with increasing paste volumes the heat conductivity is reduced and as a result concrete with higher paste to aggregate ratios shows less spalling.
There is a wide range of research worldwide on supplementary cementitious materials (SCMs) such as fly ash and slag for substituting pure cement. Such materials are suitable to be considered in a cementitious system with ordinary Portland cement (OPC) due to their high pozzolanic properties. In addition, majority of the SCMs are said to significantly improve concrete properties especially in terms of increased strength and durability. Unfortunately, the production of such SCMs is not entirely eco-friendly and also limited to certain parts of the world, hence one has to look at alternative options.
The issue of availability of resources is a strong concept that is ever-increasing, and the use of more eco-friendly SCMs in a cementitious system is furthermore attractive. Hence this paper addresses the use of eco-friendly SCMs in concrete such as rice husk ash (RHA). Despite the fact that extensive research has been done on this material, its application in a cementitious system to obtain sufficient concrete properties is still rather limited. In a country like Tanzania, high strength concrete construction is applicable in special construction cases but certainly not a high priority. Majority of construction is still undertaken using normal strength concrete. In a ternary cementitious system consisting of OPC, RHA and other readily available resources such as limestone filler (LSF), normal strength concrete can still be produced having good performance and suitable for regular on-site construction. This paper explains a possible application of obtaining sufficient concrete properties from the available resources.
Industrial wastes (bottom ash, crushed concrete fines, filter residue, paper ash and lignite fly ash) have potential for use in building materials, for instance as raw materials for clinker production, as supplementary cementitious materials (SCMs) or mineral additions in concrete. The properties of the products are dependent on the reactivity of the waste materials used, which can be classified as inert, latent hydraulic or pozzolanic. In this study, waste materials were first characterised. This was followed by theoretical considerations of the mentioned application options. Experiments were limited to evaluation of potential as SCMs and, for this purpose, activity index measurements and calorimetric and thermogravimetric analyses were performed. Finally, the synergetic effects of various waste materials were considered. Paper ash (calcium oxide source) and filter residue (amorphous silicon dioxide source) showed the best prospects for use as cementitious material components.
The current knowledge about fatigue behavior of concrete is still incomplete. This concerns especially the progress of fatigue which precedes the fatigue failure. Therefore, the process of fatigue itself under cyclic compressive loading was investigated in a systematic and comprehensive way. The aim of this investigation was to obtain a deeper insight and to provide a better understanding of the damage process occurring within the material during fatigue loading. Concrete cylinders were tested with a number of cycles to failure between 106 and 107. To investigate macroscopic and microscopic changes in the material, various methods of non-destructive and destructive testing were used. One main result was, in contrast to other authors, that the investigated changes in macroscopic material behavior could not be explained only by a development of micro-cracks. The results indicated rather, that the related changes in the fatigue behavior are mainly a result of viscous processes in the hardened cement paste, similar to the processes of creep. Based on the experimental results a description of the possible processes was derived which take place in the material structure during fatigue loading and also leads to the observed macroscopic changes in the material behavior. In this context, the results have shown that in case of isotropic material behavior a stiffness reduction related to a scalar value could not capture the damage effect on the stress-strain-relationship caused by fatigue.
Methodologies on fire risk analysis in road tunnels consider numerous factors affecting risks (risk indicators) and express the results by risk measures. But only few comprehensive studies on effects of risk indicators on risk measures are available. For this reason, this study quantifies the effects and highlights the most important risk indicators with the aim to Support further developments in risk analysis. Therefore, a system model of a road tunnel was developed to determine the risk measures.
The system model can be divided into three parts: the fire part connected to the fire model Fire Dynamics Simulator (FDS); the evacuation part connected to the evacuation model FDS+Evac; and the frequency part connected to a model to calculate the frequency of fires. This study shows that the parts of the system model (and their most important risk indicators) affect the risk measures in the following order: first, fire part (maximum heat release rate); second, evacuation part (maximum preevacuation time); and, third, frequency part (specific frequency of fire). The plausibility of These results is discussed with view to experiences from experimental studies and past fire incidents.
Conclusively, further research can focus on these most important risk indicators with the aim to optimise risk analysis.
Fatigue is of relevance not only for metals but also for concrete. The current knowledge about fatigue behaviour of concrete is, however, incomplete. This concerns especially the progress of fatigue which precedes the fatigue failure. Some macroscopic effects of this process are well known but the governing material changes behind them are still less studied. The focus of the present contribution lay on a systematic and comprehensive investigation of the fatigue process under cyclic compressive loading. The aim was to obtain a deeper insight and to provide a better understanding of the damage process in the material. Cylindrical specimens were tested with a number of cycles to failure between 106 and 107. Various methods of non-destructive and destructive testing were used to investigate macroscopic and microscopic changes in the material. One main result was that the changes in the macroscopic material behaviour could not be explained only by the development of micro cracks. The results indicated that the related changes in the fatigue behaviour originate rather from viscous processes in the cement stone, similar to the process of creep. A sound description of the possible processes was derived from the obtained experimental results which concerns material structure during fatigue loading. It has been shown that in case of isotropic material behaviour a stiffness reduction related to a scalar value could not capture the damage effect on the stress-strain relationship caused by fatigue.
The modeling and prediction of the behavior of reinforced concrete under impact load is still an engineering challenge. The scientific community has put a lot of effort into the development of this knowledge, especially after the unfortunate events of 09/11 in Manhattan. The main concern is with nuclear power plants and how to design structures that can withstand such extreme situations. An experimental investigation has been carried out to collect fundamental data and to develop a deeper understanding of the effect of impact damage on the load capacity of concrete plates. The paper presents the process on the definition of procedures and the first results of an experimental investigation on the damage and residual load capacity of reinforced concrete plates after impact load. Two types of reinforced concrete plates measuring 1.5 x 1.5 x 0.3 m were subjected to the impact of a flat-nose hard projectile. The two types were casted with the same reinforcement and 80 or 40 MPa concrete. After the impact, the plates go through planar tomography, visual inspection and an ultimate load capacity test. The results showed that the planar tomography can be used for the assessment of internal damage on concrete plates, as long as the number of scans in each direction is more than four. The visual inspection gave a good. The formation of cone cracking after the impact load showed the highest influence on the remaining load capacity of the concrete plates. More plates will be tested to confirm the indications at different damage conditions.
Die Weiterentwicklung der Verfahren und Techniken zur dauerhaften Überwachung von Bauwerken ist Gegenstand zahlreicher Forschungs- und Entwicklungsvorhaben. Der praktische Einsatz dieser Verfahren beschränkt sich bisher jedoch auf durchaus zahlreiche, jedes für sich jedoch sehr konkrete Einzelprobleme beschreibende Projekte. Einer flächendeckenden Anwendung stehen häufig – berechtigte oder unberechtigte – Bedenken zur Effizienz dieser Verfahren im Vergleich zu baupraktisch etablierten Verfahren wie z. B. regelmäßigen Bauwerksinspektionen entgegen. Weiterführende Aspekte wie optimierte Wartungskonzepte oder Lebensdauerprognosen zur begründeten Priorisierung von Ertüchtigungsmaßnahmen sind aufgrund des Fehlens zeitnah realisierbarer, monetärer Vorteile oftmals schwer vermittelbar. Dieser Beitrag soll einige grundlegende Ziele aktueller Monitoringkonzepte anhand von Projektbeispielen der BAM aufzeigen, um die Potentiale dieser Verfahren zu verdeutlichen und mögliche sinnvolle Anwendungsgebiete zu erschließen. Im Vordergrund dieses Übersichtsbeitrages stehen dabei die grundlegenden Ideen und Ziele dieser Projekte; bezüglich der Ergebnisse wird auf die entsprechenden Fachveröffentlichungen verwiesen.