Filtern
Dokumenttyp
- Zeitschriftenartikel (2)
- Vortrag (1)
Sprache
- Englisch (3)
Schlagworte
- PLSR (3) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (1)
Near-infrared (NIR) spectroscopy is a promising candidate for low-cost, nondestructive, and high-throughput mass quantification of micro¬plastics in environmental samples. Widespread application of the technique is currently hampered mainly by the low sensitivity of NIR spectroscopy compared to thermo-analytical approaches commonly used for this type of analysis. This study shows how the application of NIR spectroscopy for mass quantification of microplastics can be extended to smaller analyte levels by combining it with a simple and rapid microplastic enrichment protocol. For this purpose, the widely used flotation of microplastics in a NaCl solution, accelerated by centrifugation, was chosen which allowed to remove up to 99 % of the matrix at recovery rates of 83–104 %. The spectroscopic measurements took place directly on the stainless-steel filters used to collect the extracted particles to reduce sample handling to a minimum. Partial least squares regression (PLSR) models were used to identify and quantify the extracted microplastics in the mass range of 1–10 mg. The simple and fast extraction procedure was systematically optimized to meet the requirements for the quantification of microplastics from common PE-, PP-, and PS-based packaging materials with a particle size < 1 mm found in compost or soils with high natural organic matter content (> 10 % determined by loss on ignition). Microplastics could be detected in model samples at a mass fraction of 1 mg g-1. The detectable microplastic mass fraction is about an order of magnitude lower compared to previous studies using NIR spectroscopy without additional enrichment. To emphasize the cost-effectiveness of the method, it was implemented using some of the cheapest and most compact NIR spectrometers available.
Abstract. Biodiesel quality control is a relevant issue as biodiesel properties influence diesel engine performance and integrity. Within the European Metrology Research Program (EMRP) ENG09 project “Metrology for Biofuels”, an on-line /at-site suitable near-infrared spectroscopy (NIRS) method has been developed in parallel with an improved EN14110 headspace GC analysis method for methanol in biodiesel. Both methods have been optimized for a methanol content of 0.2 mass% as this represents the maximum limit of methanol content in FAME according to EN 14214:2009. The NIRS method is based on a mobile NIR spectrometer equipped with a fiber-optic coupled probe. Due to the high volatility of methanol, a tailored air-tight adaptor was constructed to prevent methanol evaporation during measurement. The methanol content of biodiesel was determined from evaluation of NIRS spectra by Partial Least Squares Regression (PLS). Both GC analysis and NIRS exhibited a significant dependence on biodiesel feedstock. The NIRS method is applicable to a content range of 0.1 % (m/m) to 0.4 % (m/m) of methanol with uncertainties at around 6% relative for the different feedstocks. A direct comparison of headspace GC and NIRS for samples of FAMEs yielded that the results of both methods are fully compatible within their stated uncertainties.
Multivariate data analysis is a universal tool for the evaluation of process spectroscopic data. In process analytics, huge amounts of information are produced i) by the many variables contained in one spectrum often exceeding 1000 (wavenumbers, wavelength, shifts…), and ii) the high number of spectra that is generated within the measurement period. Multivariate data analysis, often also called Chemometrics, help to extract the relevant information which is needed to examine and even control processes. Therefore, calibration models must be precise and robust, and moreover, must cover a wide range of variation of factors posing an influence on the process.
In this pre-conference course an introduction to both, explorative data analysis by PCA (Principal Component Analysis), and regression analysis by the most frequently used method, i.e. PLSR (Partial Least Squares Regression) is given. In principal, all optical spectroscopic methods are suited for multivariate evaluation. It will be demonstrated that under certain preconditions, even process NMR spectra can be predicted by PLSR models.
At first, basic principles of multivariate data analysis will be provided. This includes a short introduction into the concept of model building and interpretation of results. Detailed aspects of data pretreatment and calibration & validation strategies for chemometric models will be provided with own data from NIR, Raman and NMR spectroscopy.
In a first example, the development of an online compatible method for the quantification of methanol in biodiesel by PLSR is presented. This also includes the classification of biodiesel feedstocks by PCA and statistical tools which allow for the estimation of a full uncertainty budget.
The Raman spectroscopic prediction of Hydroformylation reaction in a miniplant is used to discuss shortcomings and pitfalls which may occur with the transfer of off-line models to the real processes. Design of experiment and strategies for suitable lab-scale experiments are presented as a possible way to overcome problems.
In a third application the prediction of the reactants of an esterification reaction based on process NMR data is demonstrated.