Filtern
Erscheinungsjahr
Dokumenttyp
- Beitrag zu einem Tagungsband (110) (entfernen)
Sprache
- Englisch (79)
- Deutsch (30)
- Mehrsprachig (1)
Schlagworte
- Behälter (9)
- Endlager (8)
- Bauartprüfung (7)
- Interim storage (7)
- Damping concrete (6)
- Metal seal (6)
- Radioaktive Stoffe (6)
- Sicherheit (6)
- Simulation (6)
- Creep (5)
Organisationseinheit der BAM
Cylindrical casks made of ductile cast iron are used for transport, interim storage and final disposal of radioactive waste in Germany. A basic design criterion is the ability to withstand a horizontal drop without impact Binders onto a foundation representative for the real ground of a storage facility. The increasing use of more cost-effective material compositions requires optimized cask geometries to reduce stresses and strains in the cask structure. For example, a non-uniform wall thickness was introduced to reduce maximum wall bending stresses. As a result, the load characteristics changed from line load to point load at bottom and lid side under horizontal drop fest conditions. Hereby, the position of highest stress inside the structure has shifted significantly. This was the reason for a systematic investigation of effects caused by small design changes or small variations of fest conditions. It led to a better understanding of the positions of high local stresses, their time history and maximum value for cylindrical casks under horizontal drop test conditions. Hence, the paper presents the lessons learnt from modeling and simulating such scenarios considering an impact without limiters onto a realistic target.
Abgeleitet aus den in Teil 3 der „Systemanalyse Konrad“ definierten Lastannahmen für den „untertägigen Anlagenbereich“ müssen Verpackungen, die der Abfallbehälterklasse I (ABK I) mit dem zusätzlichen Merkmal der störfallfesten (sf) Verpackung oder der ABK II zugeordnet werden, gemäß den „Endlagerungsbedingungen, Endlager Konrad“, nach einem „…Fall aus 5 m Höhe auf eine unnachgiebige Unterlage…“ bestimmten Anforderungen genügen.
Eine nähere Beschreibung der Prüfeinrichtung sowie die Definition detaillierter Anforderungen an das Aufprallfundament erfolgen in der „Produktkontrolle, Endlager Konrad“: „Die Prüfeinrichtung, bestehend aus einer Hebeeinrichtung und einem Fundament ist so zu gestalten, dass der Fall des Prüfmusters in jeder beliebigen Aufprallorientierung aus 5 m Höhe, gemessen von der Unterkante des Prüfmusters zum Fundament, möglich ist. Das Fundament ist aus Beton der Mindestgüte B 35 herzustellen und muss so beschaffen und verankert sein, dass keine Zerstörung in zahlreiche kleinere Bruchstücke erfolgt und keine horizontale Verschiebung des Fundamentes oder seiner Teile auftritt. Maße und Masse des Fundaments müssen so beschaffen sein, dass der Einfluss des Baugrundes unter dem Fundament auf den Aufprallwiderstand vernachlässigbar ist.“
Im Rahmen der Bauartprüfung für Behälter zur Endlagerung radioaktiver Abfälle mit zu vernachlässigender Wärmeentwicklung im Endlager Konrad wird die Bundesanstalt für Materialforschung und -prüfung (BAM) von der Bundesgesellschaft für Endlagerung (BGE) als Sachverständige hinzugezogen und ist in der Regel auch mit der Durchführung der notwendigen Fallprüfungen auf dem Testgelände Technische Sicherheit der BAM (BAM TTS) einschließlich der Bereitstellung der benötigten Prüfeinrichtungen sowie des regelkonformen Aufprallfundamentes beauftragt. Der Prozess, beginnend von der Gewährleistung einer von allen Beteiligten als gültig bewerteten Fallprüfung bis hin zur abschließenden Bewertung und Interpretation der Versuchsergebnisse erfordert dabei u.a. eine sorgfältige Planung und Fertigung der für das Endlager Konrad repräsentativen Fundamentplatte und deren Ankopplung an einen Untergrund im Sinne der „Regulations for the Safe Transport of Radioactive Material“ wie er zum Beispiel auf den beiden Fallversuchsanlagen des BAM Testgelände Technische Sicherheit (BAM TTS) zur Verfügung steht.
Um diese Anforderungen zu erfüllen muss zum einen der Erhalt der Integrität der Fundamentplatte beim Fallversuch durch eine geeignete Auswahl und kraftflussgerechte Anordnung der Stabstahl-Bewehrung sowie deren Verankerung garantiert und damit eine unzulässige Energieaufnahme durch Risse sowie eine unzulässige „… Zerstörung (der Fundamentplatte) in zahlreiche kleinere Bruchstücke …“, wie in [3] gefordert, verhindert werden. Außerdem ist zu gewährleisten, dass der Beton die Anforderungen an die vorgeschriebene Mindestgüte bzw. -festigkeit zum Zeitpunkt der Fallprüfung erfüllt, die Betonfestigkeit jedoch zur Vermeidung unnötig verschärfter Prüfrandbedingungen eine zu definierende Obergrenze nicht überschreitet.
Ausgehend von dem 2009 im Rahmen der KONTEC veröffentlichten Wissensstand präsentiert die BAM im vorliegenden Beitrag die wesentlichen Ergebnisse der zwischenzeitlich bei der Planung und Durchführung von zahlreichen Fallprüfungen gewonnenen Erfahrungen bzgl. Spezifikation und Fertigung der für die Fallversuche notwendigen Fundamentplatten sowie deren Anbindung an den Untergrund. Neben den immer wieder notwendigen Anstrengungen zur Gewährleistung einer im Rahmen der Definition korrekten Betondruckfestigkeit am Tag der Fallprüfung wird die Anpassung der Bewehrungsführung an verschiedene Fallpositionen diskutiert.
Zur Ergänzung des gültigen Regelwerks entsteht parallel zu diesem Dokument eine Fachnotiz, in der BGE und BAM die Vorgaben und Spezifikationen zur regelwerkskonformen Herstellung und Montage von Fundamentplatten für Fallprüfungen im Rahmen der Behälterbauartprüfungsverfahren für das Endlager Konrad zusammenfassen und veröffentlichen werden. Diese Fachnotiz soll detaillierte Vorgaben und Spezifikationen zur Planung, Beauftragung, Herstellung und abschließenden Prüfung eines solchen Fundamentes und dessen Anbindung an den Untergrund enthalten. Damit soll allen beteiligten Organisationen wie Antragstellern, Sachverständigen und BGE ein langfristig verlässlicher Leitfaden im Hinblick auf die Durchführung anforderungsgerechter Fallprüfungen unter definierten und reproduzierbaren Randbedingungen im Rahmen der Bauartprüfungsverfahren für das Endlager Konrad an die Hand gegeben werden.
Existing spent nuclear fuel (SF) and high active waste (HAW) management policies and practices worldwide are the result of past presumptions that sufficient reprocessing and/or disposal capacity would be available in the near term. Consequently, in the past many countries have developed specific solutions for different periods of time due to their individual national nuclear policies.
In Germany the concept of dry interim storage in dual purpose metal casks before disposal is being pursued for SF and HAW management and transport and storage licenses have been issued accordingly. The current operation licenses for existing storage facilities have been granted for a storage period of up to 40 years. This concept has demonstrated its suitability for over 20 years so far. Relevant safety requirements haven been assessed for the short-term as well as for the long-term for site-specific operational and accidental storage conditions. But in the meantime significant delays in the national repository siting procedure occured which will make extended storage periods necessary in the future.
This paper describes the current situation in Germany with regard to dry cask storage and focuses on current perspectives considering regulatory, technical, and scientific aspects for storage license renewal. Since there is one case of a storage license limitation to only 20 years due to administrative reasons, first experience is currently gathered in case of an expiring storage license. Subsequent license options have been pursued intensively including the extension of the initial storage license as well as shipping all casks to another storage facility considering an extended storage period at that storage facility as well. All safety relevant aspects have to be reviewed on basis of the current state-of-the-art which might be different from the initial safety demonstrations. That includes new safety assessment standards as well as improved knowledge base. Major issues are e.g. improved accident scenario analyses, assessment methods, and consideration of aging effects from previous operation periods. Inspection programs with respect, e.g. to bolts and seals to verify leak-tightness and lid screw pre-stress have been initiated to demonstrate proper cask conditions for extended storage as well as transportation to another storage facility.
Strategien zur Bestimmung von Temperaturen von Transport- und Lagerbehältern für radioaktive Stoffe
(2010)
The Konrad repository for not heat generating radioactive wastes was licensed first in 2002. But due to legal actions this license has not been finally confirmed before 2007. Subsequently, the Federal Office for Radiation Protection (BfS) began scheduling backfitting of the former iron ore mine into a repository. The licensed repository volume is 303,000 m3 based on estimations of expected waste volumes to be disposed off although the mine itself would offer a much larger volume. Once the repository is ready for Operation, waste packages can be disposed, but this is not expected before the end of this decade. Nevertheless, there is already today a great interest in qualified and certified waste conditioning and packaging for disposal requiring Containers, tested, evaluated and certified by BAM and BfS.
Key points of the Konrad license concern comprehensive requirements for waste products and Containers. Details are described in BfS reports, which constitute the basic documents for the license. Following the final license confirmation a revision of these documents has been requested in order to include considerations of water poisoning substances. This work is currently done by BfS in Cooperation with the NLWKN of Lower Saxony and the Institute for Safety Technology (ISTec). Concerning the specification for Containers themselves no or only minor changes are expected.
Das Endlager Konrad wurde bereits im Jahr 2002 als Endlager für nicht Wärme entwickelnde radioaktive Abfälle genehmigt. Jedoch wurde diese Genehmigung anschließend beklagt und konnte erst 2007 in letzter Instanz bestätigt werden. Nachfolgend hat das Bundesamt für Strahlenschutz (BfS) mit der Planung und Realisierung zum Umbau des ehemaligen Eisenerzbergwerkes zum Endlager begonnen. Das genehmigte Endlagervolumen beträgt 303.000 m3 und basiert auf Abschätzungen für die zu erwartende Abfallmenge. Das Bergwerk selbst böte ein deutlich größeres Volumen. Mit der Einlagerung von Behältern kann allerdings erst nach Fertigstellung des Endlagers und nach derzeitigem Stand voraussichtlich nicht vor Ende dieses Jahrzehnts gerechnet werden. Gleichwohl besteht bereits heute ein hohes Interesse an der endlagergerechten Konditionierung und Verpackung der für Konrad vorgesehenen radioaktiven Abfälle, wofür nicht zuletzt von der BAM bauartgeprüfte und vom BfS zugelassene Behälter erforderlich sind.
Kernpunkte der Endlagergenehmigung sind umfassende Anforderungen an Abfallprodukte und Behälter. Einzelheiten sind in den vom BfS der Genehmigung zu Grunde liegenden Berichten und Endlageranforderungen definiert. Diese enthalten vor allem Anforderungen an die Abfallprodukte und an die zu deren Verpackung erforderlichen Behälter. Mit der Genehmigungserteilung wurde auch eine Überarbeitung dieser Endlageranforderungen und hinsichtlich der Berücksichtigung Wasser gefährdender Stoffe gefordert. Diese Arbeiten werden derzeit vom BfS in Zusammenarbeit mit dem Niedersächsischen Landesbetrieb für Wasserwirtschaft, Küsten- und Naturschutz (NLWKN) und dem Institut für Sicherheitstechnik (ISTec) vorgenommen. Hinsichtlich der Anforderungen an die Endlagerbehälter wird allerdings davon ausgegangen, dass die für die Behälterbauartprüfung wesentlichen abfallprodukt- und behälterspezifischen Anforderungen davon nicht oder nur unwesentlich berührt sein werden.
Die Bundesanstalt für Materialforschung und -prüfung (BAM) führt im Rahmen einer Verwaltungsvereinbarung mit dem Bundesamt für Strahlenschutz (BfS) Bauartprüfungen für Behältertypen durch, die für die Endlagerung von nicht wärmeentwickelnden radioaktiven Abfällen in das Endlager Konrad vorgesehen sind.
Zur Erlangung einer Eignungsbestätigung einer Behälterbauart für das Endlager Konrad müssen die Antragssteller die Einhaltung der vom BfS festgelegten behälterspezifischen Anforderungen nachweisen. Zentrale Bestandteile der Bauartprüfung sind die Sicherheitsnachweise zur Behälterauslegung gegen mechanische Betriebs- und Störfallbelastungen sowie gegen thermische Störfallszenarien. Die Prüfanforderungen umfassen hierbei Stapeldruckprüfung, Hebeprüfung, Fallprüfung, thermische Prüfung (Brand), ggf. einschließlich Dichtheitsprüfung zum Nachweis der Einhaltung von Dichtheitsanforderungen.
Neben der Nachweisführung mittels sogenannter Baumusterprüfungen oder Obertragbarkeitsbetrachtungen können die Nachweise alternativ mittels numerischer Sicherheitsnachweise erbracht werden, sofern deren hinreichende Verifikation nachgewiesen wird, Dies kann u. a. durch den Vergleich mit hinreichend gesicherten experimentellen Ergebnissen geschehen, Die hier vorgestellten Untersuchungen sind Teil des internen Forschungsprojektes ConDrop der BAM, das zum Ziel hat, erweiterte Prüfmethoden zur Fallprüfung an Stahlblechcontainern für das Endlager Konrad mittels numerischer Beanspruchungsanalyse zu entwickeln. Dazu soll ein Finite-Elemente-(FE)-Modell entwickelt und mit experimentellen Daten, die in Fallversuchen ermittelt werden, verifiziert werden.
The Bundesanstalt für Materialforschung und –prüfung (BAM) is a federal institute for materials research and testing in Germany and has been involved in the qualification and safety evaluation procedures of metal seals from the early beginning of the interim storage licensing procedures for radioactive materials, stored in dual purpose casks. Regarding this subject, BAM investigates the long-term behavior of metal seals under the influence of temperature using experimental data and analytical approaches. The development of numerical models is in progress as well. Systematic experimental investigations performed by BAM indicate a continuous decrease of the remaining seal force and the usable resilience considering the leak tightness. Hence, there is a fundamental interest of describing time and temperature dependency to gain predictable values for the long-term behavior and to achieve reliable results with help of short-term tests.
The paper gives an overview about the sealing principle, test program and test results of metal seals of the type HELICOFLEX® HN200. The aging effect, respectively the long-term behavior in dependency of time and temperature, are introduced for two different outer liner materials, aluminum and silver.
A Memorandum of Understanding (MOU) between the Federal Institute for Materials Research and Testing (BAM) and Argonne National Laboratory (Argonne) was signed in the fall of 2014. Its objectives are to promote cooperation among scientists and specialists at BAM and Argonne and establish a framework for collaboration in the field of advanced technologies associated with the back end of the nuclear fuel cycle. Collaborative activities involving the BAM and Argonne may be implemented through the promotion of joint research activities and scientific workshops and conferences; the exchange of technical information; and visits by scientists, specialists, and graduate, postgraduate, and Ph.D. students. The first Argonne/BAM workshop was held at Argonne in October 2014 to discuss aging management issues related to the long-term dry storage of spent fuel. Major topics for potential collaboration on the extended storage of spent nuclear fuel and its subsequent transportation were identified.
Transport and storage casks for medium and high level radioactive waste are subjected to extreme heavy loads during the accidental drop scenarios prescribed by IAEA regulations and national storage acceptance criteria. Subsequently, considerable efforts have been made to optimize impact limiting structures aiming to reduce cask stresses and deformations. Though, their benefits can only fully be exploited, if the energy absorbing behavior is reliable simulated by numerical models which play an increasingly important role in safety assessments.
BAM has had conducted the 5-years research project ENREA in order to overcome the problems caused by the use of simplified, not sufficiently validated or even defective computational concepts for damping materials. While major results of the just recently completed program will be presented, the focus is laid on the question whether these Outputs provide a solid foundation for approximating impact limiting structures in all relevant configurations.
So far, material models have been implemented for spruce, Polyurethane foams and damping concrete based mainly on small and medium scale compression test results. The experimental program performed at BAM comprised likewise guided drop tests and, especially for concrete, penetration tests. Although the resulting numerical simulations showed good agreement with measured values, it turned out to be necessary to consider further effects with regard to e.g. multiaxial stress States, shearfailures of shock absorbing components and their interaction with enclosed or enclosing structures. Thus, the strengths and application constraints of the actual models will be shown as well as details about further research needs, if any.
The German repository “Konrad” is approved for the final storage of approximately 300.000 m³ of non-heat generating radioactive waste considering also the expected residues from operation and decommissioning of current power plants. According to the latest survey as constituted end of 2014, a large proportion of this volume already exists, of which 100.288 m³ are fully loaded packages. As prerequisite for their “Konrad” acceptance, the vessels have to be designed against operational and accidental conditions of the site and be manufactured according to adequate quality assurance programs. The respective safety assessment performed by BAM on behalf of the Federal Office for Radiation Protection is a major challenge especially for those casks that had been produced and loaded already some decades ago. Typically, they were manufactured in big numbers over a longer period of time involving a lot of constructional and management changes. This fact in combination with the previously rather low documentation standards often causes relevant uncertainties about the specific physical and geometrical characteristics of the cask materials and components as well as about details concerning their whole assemblage.
This paper highlights current assessment strategies for such older vessels including cubic steel sheet containers as well as cylindrical thick-walled casks. As compliance with each “Konrad”-requirement can hardly be shown independently, only integrated approaches promises success: First, a broader concept of data collection has to be implemented that allows closing documentation gaps by linking dispersed and diverse data, e.g. delivery slips and handwritten fabrication records, by including plausibility considerations as well as random inspection programs. Thereby, the relevant properties of all applied casks have to be identified and their potential range should be quantified as accurately as possible. This knowledge is necessary to define one or more representative configurations of the cask as the base for design testing. The actual investigation program must enable to track the influence of deviations and determine safety margins especially in the likely case that not the most conservative setting of all cask features can be tested. The paper evaluates the respective ongoing efforts of industrial applicants and summarizes BAM experiences and associated research projects.
The German nuclear waste management strategy consists of dry interim storage of spent fuel inside dual purpose casks and its subsequent direct final disposal in a deep geological repository. Interim storage is limited to 40 years so far, but will have to be extended until repository site selection and operation is concluded, potentially up to 100 years. In this context, research on the long term performance of safety relevant cask components and fuel rod integrity during such extended periods of time is of outmost importance. The barrier function of the fuel cladding depends on its integrity under operational and accidental conditions along with storage and subsequent transportation and is mainly affected over time by altering of the cladding microstructure and by thermo-mechanical conditions during reactor operation and subsequent wet and dry storage.
This paper focuses on failure mechanisms regarding cladding embrittlement caused by physical phenomena concerning hydrogen dissolution and precipitation of hydrides in the zirconium matrix. Within this context, potential cladding integrity issues under extended interim storage conditions followed by transportation are emphasized.
Delayed hydride cracking (DHC) is a well-known time-dependent temperature-activated phenomenon failure mechanism of the fuel cladding during reactor operation. The phenomenon consists of hydrogen diffusion and hydride precipitation at the tip of an initial crack and the propagation of the crack to an approximate distance equal to the length of the hydride. This failure mechanism is temperature-activated phenomenon and enhances along with thermal cycling of the fuel cladding, e. g. during reactor shutdowns. DHC shows limited relevance under quasi static storage conditions with continuously lowering temperatures. However, the literature points that DHC may occur when the temperature during storage decreases to a certain level after some decades and in combination with stress concentrations in the cladding material.
When spent fuel is transferred to dry storage by vacuum drying, the cladding temperature raises up to peak temperatures of ~370°C. Under these conditions, hydrides dissolute into the zirconium matrix up to the solubility limit defined by the peak temperature and this amount of hydrogen can precipitate in a radial re-oriented fashion due to the temperature decrease during storage. Cladding materials with radially precipitated hydrides show significant embrittlement. Radially oriented hydrides are perpendicularly oriented to hoop stresses representing the most critical configuration. Brittle failure of the cladding then occurs by crack propagation through radially oriented hydrides and finally through the zirconium matrix. The susceptibility to radial hydride precipitation depends on cladding material type and microstructure, hydrogen content, pre-drying hydride distribution, irradiation conditions, and temperature and stress histories during drying and storage operations.
This paper addresses major considerations concerning spent fuel cladding embrittlement due to hydride precipitation with regard to the boundary conditions of dry spent fuel storage in Germany. Analytical, numerical, and experimental approaches are to be discussed by BAM in order to identify the specific needs for future R&D work in that area with the purpose to provide the necessary data base for proper safety demonstration and evaluation along with future extended storage licensing procedures.
The German approach of storing spent nuclear fuel in dual purpose casks until final disposal is based on individually licensed storage sites concerning specific nuclear inventories and dual purpose cask types. The currently approved license period is maximum 40 years.
With nuclear policy changes including the phase-out decision of 2011 and a new approach for the HLW repository siting process set up 2013 by law also the spent fuel and HLW management strategy has to be adapted. This includes the timely development of disposal container concepts as part of the overall repository siting process and the need for longer interim storage periods until final disposal. Other aspects affect new regulations about the financing of the nuclear waste management by the industry and the public sector, the restructuring of responsible authorities in 2016/2017 and the adaption of R&D funding programs addressing also pre-disposal (or extended interim storage) issues.
BAM as a Federal Research Institute has been responsible for or in charge of container safety Evaluation for transport and storage casks for radioactive waste for several decades and started addressing potential Extended interim storage issues already several years ago. This included participation in international projects at the IAEA or in the U.S. Extended Storage Collaboration Program (ESCP) as well as long term laboratory tests with metal seals, elastomeric seals and polymers for neutron shielding purposes. Test results of BAM are published regularly and gained data provide valuable information about thermo-mechanical and radiological degradation effects as well as the long term Performance of respective cask components. Regarding the reliable extrapolation and prediction of the long term Performance of cask materials and components for time periods of up to 80 or even 100 years the continuation and extension of laboratory tests and the development of analytical and numerical simulation models and tools is essential and under way.
The Bundesanstalt für Materialforschung und –Prüfung (BAM) runs an investigation program on the long-term behavior of multi-component metal seals. Such seals are used in a wide area of applications including transport and storage casks for spent nuclear fuel and high level radioactive waste.
The seal function is mainly based on the compression of the inner helical spring, which generates the necessary seal force to keep the sealing surfaces in close contact. This in turn leads to a plastic deformation of the outer jacket of the seal, comprised of highly ductile aluminum or silver that adapts to the sealing surfaces of cask body and bolted lid, thus providing high Level leak tightness. In Germany, those casks are licensed for Interim storage periods of up to 40 years or more if extended Interim storage would become necessary before a final repository is available. Thus, the sealing performance has to be evaluated, including factors like elevated temperature due to decay heat or mechanical loads due to transport under normal as well as accident conditions. Long-term investigations at BAM have been running over the last nine years to identify and evaluate the seal performance by measuring the remaining seal force, the useable resilience and the leakage rate after various time intervals at temperatures ranging from room temperature up
to 150 °C. It was found that the seal force and useable resilience decrease with time and temperature, caused by creep deformation of the outer jacket. In order to obtain an analytical description for the seal behavior and to achieve more information on the material behavior under application conditions a comprehensive investigation program with Focus on aluminum as outer jacket material was launched. The program includes material investigations such as compression and tension creep tests with representative basic materials. An additional test setup allows for the continuous measurement of the remaining seal force at temperatures of up to 150 °C. Furthermore, seal segments are compressed and stored in heating chambers, thus producing segments at different stages of the aging process. The segments are investigated regarding the development of the contact area width, jacket thickness and microstructural changes. This data will be used to develop material models and an analytical description of the time and temperature dependent long-term sealing behavior. This paper explains the current status of gained test results and modelling approaches and closes with an outlook to the future Project plans.
Polyurethane foam used as impact limiter material undergoes high plastic deformations, whereat the resulting stress-strain relations strongly depend on loading speed and temperature. This paper discusses the efforts necessary to develop a reliable numerical foam simulation model focussing on generation and implementation of temperature- dependent yield curves
It is important to evaluate the effect of thermal ageing on the sealing performance of metal gaskets under high temperature for long-term usage. Therefore, in order to gain representative data for this kind of metal-sealed lid System, BAM is currently performing laboratory tests of different gasket types with aluminum and silver jackets at three different temperatures under static conditions up to four years so far, using test flanges for gaskets with full scale cross section diameter but much smaller outer diameter. On the other hand, in order to investigate the applicability of the numerical methodology to evaluate the long-term behavior of the metal gaskets, such as a correlation between seal pressure force and holding time, CRIEPI is developing a modeling method including material tests (tensile and creep tests) at high temperature. In this paper, the applicability of the finite element method (ABAQUS) to predict the recovery displacement and residual seal pressure force of the gasket complex was verified by comparing the calculated values with BAM’s laboratory test results under the joint research agreement between BAM and CRIEPI.
In drop test scenarios related to assessing and licensing the storage procedure of spent fuel and high active waste, the casks under examination are generally not equipped with impact limiters. Hence, the extent of mechanical stresses in case of an assumed handling accident is largely affected by the ground properties of the reception hall floor in the specific storage facility.
Unlike conventional brittle foundation materials, damping concrete performs quite well in such applications as it features high stiffness as well as high energy absorption due to the filler pore volume. However, its damping ability is not sufficiently exploited in current finite element (FE) calculations due to a lack of advanced material models for simulating its impact response. An implementation of qualified concepts that account for plastic, strain rate dependent behavior requires additional information that has to be provided by systematic test series.
BAM recently started a research project to generate such data, subsequently to develop and to improve numerical methods for the analysis of impact limiters and damping foundation material and thus to optimize safety assessment tools for the design of transport and storage casks. A major part of this research concerns dynamic compression tests of variably shaped specimens conducted at a servo hydraulic 1MN impact testing machine as well as at a BAM facility for guided drop tests. This presentation focuses 100mm damping concrete cubes deformed vertically at constant rates under different constraint conditions. For example, a special fitting jig was constructed to subject the specimens to multi-axial loading. Thereby a deformation of 60% could be applied.
Simulation was conducted by FE code ABAQUS based on material models Concrete damaged plasticity and Crushable foam which both allow defining rate sensitive nonlinear stress-strain relations in compression beyond the classic metal plasticity approach.
In Germany, for the transport and storage of spent nuclear fuel, casks with double closure lid systems are used, which are equipped with Helicoflex® metal seals. The original interim storage period for these casks was planned to be 40 years. However, recent political developments indicate that a storage time of more than 80 years might be necessary. Therefore, the current storage licenses have to be renewed in due course, which requires extended knowledge of the long-term behaviour of all cask components.
At the Bundesanstalt für Materialforschung und -prüfung (BAM), metal seals have been investigated after ageing at temperatures between room temperature and 150 °C for up to 7 years. At regular intervals the seals have been tested for leakage rate as well as for their mechanical behaviour. From these tests pronounced influence of ageing could be shown which results in the decrease of the seal force and the useable resilience. The main reason attributed to these performance changes is the increasing permanent deformation of the outer layer of the seal due to creep. So far, an explicit analytical description of the long-term behaviour that could be used for predictions exceeding the tested ageing times and temperatures was not suitable.
In addition to the component tests that were already conducted, a comprehensive investigation programme has been started to describe the mechanical behaviour of the individual seal components.
The individual seal components are tested regarding different material characteristics including creep, deformation and microstructural properties. The comparability of the material characterization is ensured by comparing the basic raw material of the specimen with the actual component material.
Furthermore, detailed investigations of the time and temperature dependent deformation behaviour are realized by ageing seal segments at multiple temperatures for different periods of time and employing standardized tests.
By analysing the acquired data in combination with the ongoing long-term component tests a dataset for analytical prediction of the long-term behaviour of the seals is intended for an extended period of time under a certain temperature regime.
Finite element analysis (FEA) has been carried out for investigation of damping concrete under different impact loading conditions with a built-in material model and damage criteria available in FEA code ABAQUS.
At first, all parameters for the selected material model had been derived from compression Tests of cubic specimens. After that, a validation was carried out with different static and dynamic penetration tests. Finally, a 5 meter real drop test with a 23 Mg cylindrical cask could successfully be simulated.
The investigation of the long-term performance of sealing systems employed in containers for radioactive waste and spent nuclear fuel is one research focus area for division 3.4 “Safety of Storage Containers” at the Bundesanstalt für Materialforschung und -prüfung (BAM). Our investigations comprise investigations on metallic and elastomeric seals and covers experimental investigations to get a database on the component/material behaviour, work on analytical descriptions and numerical analysis. Our aim is to understand the long-term behaviour of the sealing systems for evaluation of their performance during possible extended interim storage and subsequent transportation.
The general aim of this research is the development of methods for predicting mechanical behavior and identification of limiting conditions to prevent brittle failure of high-burnup (HBU) pressure water reactor (PWR) fuel cladding alloys. A finite element (FE) model of the ring compression test (RCT) was created to analyze the failure behavior of zirconium-based alloys with radial hydrides during the RCT. An elastic-plastic material model describes the zirconium alloy. The stress-strain curve needed for the elastic-plastic material model was derived by inverse finite element analyses. Cohesive zone modeling is used to reproduce sudden load drops during RCT loading. Based on the failure mechanism in non-irradiated ZIRLO® claddings, a micro-mechanical model was developed that distinguishes between brittle failure along hydrides and ductile failure of the zirconium matrix. Two different cohesive laws representing these types of failure are present in the same cohesive interface. The key differences between these constitutive laws are the cohesive strength, the stress at which damage initiates, and the cohesive energy, which is the damage energy dissipated by the cohesive zone. Statistically generated matrix-hydride distributions were mapped onto the cohesive elements and simulations with focus on the first load drop were performed. Computational results are in good agreement with the RCT results conducted on high-burnup M5® samples. It could be shown that crack initiation and propagation strongly depend on the specific configuration of hydrides and matrix material in the fracture area.
Im Zuge des Forschungsvorhabens ENREA (Entwicklung rechnerischer Analysemethoden für stoßdämpfende Strukturen beim Anprall oder Absturz von Abfallgebinden) führt die BAM systematische Untersuchungen an stoßdämpfenden Werkstoffen, unter anderem an Fichtenholz, durch. Zweck der mit diesen Untersuchungen erzeugten Datenbasis ist die Erstellung und Parametrierung eines Finite-Elemente- (FE-) Materialmodells, das die Modellierung holzgefüllter stoßdämpfender Bauteile von Transportbehältern für radioaktive Stoffe in der FE-Simulation ermöglichen soll.
Anhand von Ergebnissen aus der ersten Versuchsphase werden der Einfluss der Dehnrate und der Faserorientierung auf das Kraft-Verformungs-Verhalten von Fichtenholz diskutiert. Anschließend wird die rechnerische Modellierung von Fichtenholz diskutiert und die Anforderungen an ein Materialmodell werden erläutert.
Due to delays in the siting procedure to establish a deep geological repository for spent nuclear fuel and high level radioactive waste as well as in construction of the already licensed Konrad repository for low and intermediate level radioactive waste, extended periods of interim storage become more relevant in Germany. BAM is involved in most of the cask licensing procedures and especially responsible for the evaluation of cask-related long-term safety issues.
The long-term performance of elastomer seals for lid systems of transport and storage casks, whether used as auxiliary seals in spent fuel casks or as primary seals for low and intermediate level waste packages, is an important issue in this context. The polymeric structure of these seals causes a complex mechanical behavior with time-dependent sealing force reduction.
The results of a comprehensive purpose-designed test program consisting of basic compression and tension tests as well as relaxation tests on unaged specimens of representative types of elastomers (fluorocarbon rubber (FKM) and ethylene propylene diene rubber (EPDM)) at different temperatures and strain rates are presented. They were used to identify the constitutive behavior and to obtain parameters for finite element material models provided by the computer code ABAQUS®. After estimating the influence of uncertainties such as Poisson’s ratio and friction coefficient by sensitivity analyses, the chosen parameters had to prove their suitability for the finite element simulation of the specimen tests themselves.
Based on this preliminary work the simulation of a specific laboratory test configuration containing a typical elastomer seal with circular cross section is presented. The chosen finite element material model and the implemented parameters had to show that they are able to represent not only the specimen behavior under predominantly uniaxial load but also the more complex stress states in real components. Deviations between the measured and calculated results are pointed out and discussed.
For the consideration of long-term effects in the simulation of elastomer behavior, test results of aged specimens are needed. First information about a new test program, started recently and planned to provide these data, are given.
Während des Transportes sind Behälter für hoch radioaktive Abfälle durch stoßdämpfende Bauteile vor Einwirkungen, die aus Unfallszenarien gemäß den IAEA Regularien resultieren können, weitestgehend geschützt. Nach dem Entfernen dieser Komponenten im Rahmen der Einlagerung ins Zwischenlager müssen Vorkehrungen getroffen sein, um Beanspruchungen der Behälter aus möglichen Handhabungsunfällen im Empfangsbereich zu reduzieren. Die Maßnahmen müssen vor allem darauf abzielen, die stoßdämpfenden Eigenschaften der potentiellen Aufprallflächen zu optimieren. Da Standardmaterialien für Fundamente nur ein geringes Energieabsorptionsvermögen aufweisen, wurde durch die Firma HOCHTIEF eine neuartige Betonmixtur entwickelt, bei der ein spezieller Leichtzuschlag zum Einsatz kommen. Zur Charakterisierung dieses sogenannten Dämpferbetons liegen Standardkennwerte vor sowie Messwerte aus Eindringversuchen, die zur Qualitätssicherung für jede Produktcharge durchgeführt werden. Das stoßdämpfende Potential des neuen Werkstoffs kann jedoch nur dann vollkommen ausgeschöpft werden, wenn die Energieabsorption in numerischen Simulationen der Behälterabstürze über die gesamte Belastungsdauer zuverlässig wiedergegeben wird. Für die Implementierung und Anpassung eines entsprechenden Materialmodelis in einem Finite Elemente (FE) Programm
sind Daten aus systematischen Druckversuchen mit Variation der relevanten Einflussgrößen erforderlich. An der BAM werden daher im Rahmen eines werkstoffübergreifenden Forschungsvorhabens zur Untersuchung von stoßdämpfenden Strukturen auch die Eigenschaften von Dämpferbeton experimentell untersucht und zugehörige numerische Methoden entwickelt. Der aktuelle Beitrag behandelt die Ergebnisse der ersten Projektphase, in der kubische Probekörper mit der Kantenlänge 100mm bei unterschiedlichen Lagerungsbedingungen statisch und dynamisch gestaucht wurden. In nachfolgenden Versuchen wird der Einfluß der Probengröße ermittelt sowie die Eignung der verwendeten Materialmodelle anhand realistischer Belastungssituationen validiert.
Versuchsprogramm.
Zur numerischen Simulation von Transport- und Lagerbehältern für radioaktive Stoffe unter mechanischen Unfallbedingungen sind geeignete
Materialmodelle und zugehörige Parametersätze für alle relevanten Behälterbauteile und den Aufpralluntergrund sowie gegebenenfalls für weitere am Störfall beteiligte Komponenten erforderlich.
Sie bilden eine wesentliche Grundlage um für unterschiedliche Belastungsvarianten und Temperaturen zuverlässige Berechnungsergebnisse zu ermitteln, die umfangreiche experimentelle Erprobungen zumindest in Teilen ersetzen und damit einen zentralen Bestandteil von sicherheitstechnischen Nachweisen in gefahrgut- und atomrechtlichen Zulassungs- und Genehmigungsverfahren bilden können. Für die Auslegung der Behälter von besonderer Bedeutung ist die Effizienz der eingesetzten energieabsorbierenden Elemente, wie beispielsweise Stoßdämpfer am Behälterdeckel oder -boden bzw. äquivalente Strukturen auf oder im Fundament von Zwischen- und Endlagern.
Diese Bauteile, die häufig aus Holz, Polyurethan (PU) - Schaum oder Dämpferbeton hergestellt werden, erfahren beim Auf- oder Anprall erhebliche plastische Deformationen, deren Verteilung und Größenordnung u.a. von der Belastungsgeschwindigkeit, dem Belastungsverlauf und der Temperatur bestimmt werden. Die Berücksichtigung dieser Faktoren in dynamischen Finite Elemente (FE) Berechnungen, die den heutigen Stand der Simulationstechnik repräsentieren, setzt eine systematische Datenbasis für den stoßdämpfenden Werkstoff voraus und die Implementierung dieser Informationen in numerischen Materialformulierungen.
An der BAM wird seit Ende 2008 im Rahmen des vom BMBF geförderten Forschungsvorhabens ENREA (Entwicklung rechnerischer Analysemethoden für stoßdämpfende Strukturen beim Anprall oder Absturz von Abfallgebinden) die experimentelle Bestimmung derartiger Daten sowie die Anpassung und teilweise Neuentwicklung geeigneter Materialmodelle betrieben.
Rubbers are widely used as main sealing materials for containers for low and intermediate level radioactive waste and as additional component to metal seals in spent fuel and high active waste containers. The save encapsulation of the radioactive container inventory has to be guaranteed according to legislation and appropriate guidelines for long term storage periods as well as down to temperatures of -40 °C during transport.
Therefore the understanding of failure mechanisms that lead to leakage at low temperatures is of high importance.
It is known that the material properties of rubbers are strongly temperature dependent. At low temperatures this is caused by the rubber-glass transition (abbr. glass transition). During continuous cooling the material changes from rubber-like entropy-elastic to stiff energy-elastic behaviour, that allows nearly no strain or retraction, due to the glass transition. Hence rubbers are normally used above their glass transition but the minimum working temperature limit is not defined precisely, what can cause problems during application. Therefore the lower operation temperature limit of rubber seals should be determined in dependence of the material properties.
The results of Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA) are combined with the results of standardized measurements as the compression set according to ISO 815. To reduce the test time of the standard tests a faster technique was developed.
Additionally, the breakdown temperature of the sealing function of complete O-ring seals is measured in a component test setup to compare it with the results of the other tests. The experimental setup is capable of measuring the leakage rate at low temperatures by the pressure rise method.
A fluorocarbon rubber (FKM) was selected for this investigation as it is often used for radioactive waste containers. Some materials (seals and test sheets) were purchased from a commercial seal producer and some materials were compounded and cured at BAM in form of rubber sheets.
Elastomer seals are widely used as barrier seals in containers for low and intermediate level radioactive waste and in some countries for spent fuel transportation casks. Depending on the area of use, the rubber materials have to demonstrate proper sealing performance with regard to mechanical, thermal and environmental conditions as well as irradiation during the entire operation period.
In Germany the low and intermediate level radioactive waste is planned to be disposed in the Konrad repository in standardized containers. Many of these containers use an elastomer seal between lid and container body. Depending on the radiactive inventory and a possible containment of the waste in inner barrels and/or concrete structures, such containers may require a specific leak tightness. In such cases, specified leakage rates are shall not be exceeded by the the seals to keep potential activity releases from the inventories well below defined limits.
Generally, all waste containers have to fulfill the waste acceptance criteria for the Konrad repository as defined by the reports BfS SE-IB-29/08 and SE-IB-30/08. From these criteria several requirements for seal performance are derived. The seals have to:
- ensure full functionality until final container disposal,
- maintain its function in case of a thermal or mechanical accident,
- ensure encapsulation also at -20 °C.
This combination of requirements is challenging especially as a seal exchange, which is typical for many other applications, is hardly possible and thus a sound understanding of how to perform safety evaluation of containers is required. Therefore BAM has initiated investigations on elastomer seal behaviour. This work focuses on low temperature behaviour and sealing performance concerning static conditions as well as partial loss of compression and ageing of elastomer seals. Concerning ageing, property changes caused by long-term thermooxidative conditions as well as gamma irradiation are investigated.
This contribution presents an overview and explanation of the aims of the ongoing research and gives an update of the most relevant results.
Safety of long term containment and storage of radioactive waste is an essential issue, which is increasingly gaining international attention. Extending interim storage beyond initial license periods is one of the major challenges worldwide.
BAM has been involved in all kinds of radioactive waste container safety evaluation for storage and transportation including their long term performance from the very beginning. Today, all work related to the safe management of radioactive waste is linked by the activity field “Nuclear Waste Management” within the Focus Area “Energy” at BAM and in conjunction with a research strategy and agenda. Most recently, the working group “Long Term Safety of Container Systems and Components” was established to launch and perform research projects related to safety issues concerning the extended interim storage of radioactive waste.
For example, within our project LaMEP, we investigate ageing effects of metal and elastomer seals as well as polymeric neutron shielding materials, which are container components that fulfil major safety functions. The results of the experiments help to understand the long term behaviour of these components. Likewise, our project BRUZL started at BAM in 2018 with the aim of developing a fracture mechanics approach to understand and describe a potential brittle failure mechanism of fuel cladding during long-term interim storage. BAM also contributes to the GRS project “Development of methods and models and international exchange for safety evaluation in the frame of interim storage of radioactive waste”. Additionally, BAM is involved in several international research programmes dealing with extended interim storage, such as the European Joint Programme on Radioactive Waste Management (EURAD), the Extended Storage Collaboration Program (ESCP) and IAEA Coordinated Research Projects.
The present contribution provides a comprehensive overview of BAM research activities contributing to national and international gap analyses and to filling knowledge gaps regarding the safe long term management of radioactive waste.
Elastomers show a high versatility which makes them ideal materials for sealing applications in various fields. Especially under changing application conditions the high recovery potential of this class of material is beneficial to compensate temperature or pressure fluctuation, and geometrical changes resulting from mechanical loads in e.g. accident conditions. Out of these reasons elastomers are also used in containers for low and intermediate level radioactive waste and for spent fuel transportation casks. In casks designed for low and intermediate level waste elastomer seals can act as primary seal responsible for the containment function whereas in spent fuel storage and transportation casks (dual purpose casks (DPC)) elastomer seals are used as auxiliary seals to allow leakage rate measurements of metal barrier seals. An inherent prerequisite for this kind of application is the Long time-scale of operation without or with limited possibility of seal replacement. In Germany an interim storage license for DPC`s is typically issued for 40 years, a timeframe which might increase in the future due to challenges of the final repository siting procedure. For low and intermediate level waste, also long time periods are required before final disposal can be achieved. Therefore, the performance of elastomer seals over extended time periods is, as for other applications, of high importance.
A typical approach to ensure long-term functionality is to perform accelerated aging tests to calculate an estimated lifetime by assuming e.g. Arrhenius like equations for the timetemperature relationship. This approach requires a suitable end of life criterion considering the application of interest. This often can represent a challenge on its own.
As BAM is involved in most of the cask licensing procedures and especially responsible for the evaluation of cask-related long-term safety issues we initiated several test programs for investigating the behavior of elastomer seals. Experiments concerning the low temperature performance down to -40 °C and the influence of gamma irradiation have been started first.
Currently the thermal aging behavior of elastomer seals, which is the topic of this contribution, is examined. For our aging investigations we use a broad approach to first determine the property changes in different elastomer materials due to thermo-oxidative aging at elevated temperatures and secondly, we test how the typical methods of lifetime extrapolation can be applied to these results. This Approach enables us to detect and exclude undesired side effects which very often influence lifetime estimations. In this contribution, our recent results are extended. The results show that lifetime estimation based on single material properties can be misleading and therefore a combination of several methods is recommended.
Testing and numerical simulation of elastomeric seals under consideration of time dependent effects
(2016)
Due to delays in the siting procedure to establish a deep geological repository for spent nuclear fuel and high level waste and in construction of the already licensed Konrad repository for low and intermediate level waste, extended periods of interim storage will become more relevant in Germany. BAM is involved in most of the cask licensing procedures and is responsible for the evaluation of cask-related long-term safety issues. Elastomeric seals are widely used as barrier seals for containers for low and intermediate level radioactive waste. In addition they are also used as auxiliary seals in spent fuel storage and transportation casks (dual purpose casks (DPC)).
To address the complex requirements resulting from the described applications, BAM has initiated several test programs for investigating the behavior of elastomeric seals. These include experiments concerning the hyperelastic and viscoelastic behavior at different temperatures and strain rates, the low temperature performance down to -40°C, the influence of gamma irradiation and the aging behavior.
The first part of the paper gives an overview of these tests, their relevant results and their possible impact on BAM’s work as a consultant in the framework of approval and licensing procedures.
The second part presents an approach of the development of a finite element model using the finite element code ABAQUS®. The long-term goal is to simulate the complex elastomeric behavior in a complete lid closure system under specific operation and accident conditions.
With the clear expectation of the need for extending spent fuel storage in Germany beyond the initial license period of maximum 40 years additional material data and knowledge about the long term performance and integrity of casks and internals like fuel rods will be required to meet major safety goals and regulatory requirements.
Based on a broad knowledge base about fuel cladding behavior, degradation mechanisms and related potential failure mechanisms, e. g. induced by reoriented Hydride precipitation, as illustrated in this paper, a specific gap analyses for the German situation regarding fuel conditions and cladding materials should identify the specific knowledge gaps to be addressed and closed in the near future. This is of specific interest as all spent fuel assemblies are going to be transferred to dry cask storage with the next decade and as a consequence of the German nuclear phase-out decision.
Within several decades, BAM as a Federal materials research institute gathered a broad range of expertise in the safety evaluation of materials, components and casks under operational and accidental thermal and mechanical conditions. This paper elucidates selected Basic considerations regarding technical and scientific knowledge about the long term aging performance and potential failure mechanisms of fuel cladding materials.
Under consideration of the national R&D funding policy which has been adapted to the extended interim storage or pre-disposal needs and the competences of BAM, its future R&D strategy is explained and some R&D objectives have already been identified. BAM will continue and expand ist engagement in the area of investigating fuel cladding material behavior in the long term and developing validated simulation and analyses tools in collaboration with national and international partners. R&D outcomes shall improve the knowledge-base to close identified knowledge gaps in the area of demonstrating fuel cladding integrity and to provide crucial information with regard to future safety assessments for the extended interim spent fuel storage.
Sicherheitsbewertung von Lagerbehältern bei Auslaufen einer befristeten Zwischenlagergenehmigung
(2013)
Bei der sicherheitstechnischen Begutachtung der behälterspezifischen Aspekte nach Ablauf einer Zwischenlagergenehmigung ist entsprechend einer Neubeantragung zu verfahren. Die Sicherheitsbewertung erfolgt nach dem aktuellen Stand von Wissenschaft und Technik bei Berücksichtigung der zur Behälterbauart bereits vorliegenden Sicherheitsnachweise und Begutachtungsergebnisse sowie der physikalischen und chemischen Alterungseinflüsse der bisherigen Zwischenlagerung. Am Beispiel einer beantragten weiteren Zwischenlagerung nach Auslaufen einer auf 20 Jahre befristeten Genehmigung und dem notwendigen Behältertransport zu einem neuen Zwischenlager werden Erfahrungen bzgl. der durchgeführten Sicherheitsbewertung zur Erfüllung der Technischen Annahmebedingungen des neuen Behälterlagers dargestellt.
Dual purpose casks for the transportation and storage of spent nuclear fuel and other radioactive materials require very high leak-tightness of lid closure Systems under accident conditions as well as in the long-term to prevent activity release. For that purpose metal seals of specific types with an inner helical spring and outer metal liners are widely used and have shown their excellent performance if certain quality assurance requirements for fabrication and assembling are satisfied. Well defined surface roughness, clean and dry inert conditions are therefore essential. No seal failure in a loaded cask happened under these conditions until today.
Nevertheless, the considered and licensed Operation period is limited and all safety assessments have been performed and approved for this period of time which is 40 years in Germany so far. But in the meantime longer storage periods might be necessary for the future and therefore additional material data will be required. BAM is involved in the qualification and evaluation procedures of those seals from the early beginning. Because long-term tests are always time consuming BAM has early decided to perform additional tests with specific test seal configurations to gain a better understanding of the long-term behavior with regard to seal pressure force, leakage rate and useable resilience which is safety relevant mainly in case of accidental mechanical loads inside a storage facility or during a subsequent transport. Main test parameters are the material of the outer seal jacket (silver or aluminum) and the temperature. This paper presents the BAM test program including an innovative test mock-up and most recent test results. Based on these data extrapolation models to extended time periods are discussed, and also future plans to continue tests and to investigate seal behavior for additional test parameters are explained.