Filtern
Dokumenttyp
- Zeitschriftenartikel (5)
- Vortrag (4)
- Beitrag zu einem Tagungsband (1)
- Dissertation (1)
Sprache
- Englisch (11)
Schlagworte
- Concrete (3)
- Digital twin (3)
- Model updating (3)
- Cycle jump (2)
- Damage (2)
- Damage detection (2)
- Proper generalized decomposition (2)
- Random field (2)
- Variational Bayesian (2)
- Adaptive time stepping (1)
Organisationseinheit der BAM
- 7.7 Modellierung und Simulation (11) (entfernen)
Paper des Monats
- ja (2)
Eingeladener Vortrag
- nein (4)
Using digital twins for decision making is a very promising concept which combines simulation models with corresponding experimental sensor data in order to support maintenance decisions or to investigate the reliability. The quality of the prognosis strongly depends on both the data quality and the quality of the digital twin. The latter comprises both the modeling assumptions as well as the correct parameters of these models. This article discusses the challenges when applying this concept to realmeasurement data for a demonstrator bridge in the lab, including the data management, the iterative development of the simulation model as well as the identification/updating procedure using Bayesian inference with a potentially large number of parameters. The investigated scenarios include both the iterative identification of the structural model parameters as well as scenarios related to a damage identification. In addition, the article aims at providing all models and data in a reproducibleway such that other researcher can use this setup to validate their methodologies.
Quasi-brittle materials exhibit strain softening. Their modeling requires regularized constitutive formulations to avoid instabilities on the material level. A commonly used model is the implicit gradient-enhanced damage model. For complex geometries, it still Shows structural instabilities when integrated with classical backward Euler schemes. An alternative is the implicit–explicit (IMPL-EX) Integration scheme. It consists of the extrapolation of internal variables followed by an implicit calculation of the solution fields. The solution procedure for the nonlinear gradient-enhanced damage model is thus transformed into a sequence of problems that are algorithmically linear in every time step. Therefore, they require one single Newton–Raphson iteration per time step to converge. This provides both additional robustness and computational acceleration. The introduced extrapolation error is controlled by adaptive time-stepping schemes. This paper introduced and assessed two novel classes of error control schemes that provide further Performance improvements. In a three-dimensional compression test for a mesoscale model of concrete, the presented scheme was about 40 times faster than an adaptive backward Euler time integration.
Simulating high-cycle fatigue with continuum models offers the possibility to model stress-redistributions, consider 3Dstress states and simplifies extensions to multi-physics problems. The computational cost of conventional cycle-by-cycle time integrations is reduced by reformulating the fatigue problem as an ordinary differential equation for the material state and solving it with high-order adaptive time integration schemes. The computational cost of calculating the Change of the material state in one cycle is further reduced by a high-order fatigue-specific time integration. The approach is exemplarily demonstrated for a fatigue extension of the implicit gradient-enhanced damage model in 3D and compared to experimental Wöhler lines.
Numerical models are an essential tool in predicting and monitoring the behavior of civil structures. Inferring the model parameters is a challenging tasks as they are often measured indirectly and are affected by uncertainties. Digital twins couple those models with real-world data and can introduce additional, systematic sensor uncertainties related to the sensor calibration, i.e. uncertain offsets and calibration factors.
In this work, the challenges of data processing, parameter identification, model selection and damage detection are explored using a lab-scale cable stayed bridge demonstrator. By combining force measurements in the cables with displacement measurements from both laser and stereo-photogrammetry systems, the elastic parameters of a three-dimensional finite element beam model are inferred.
Depending on the number of sensors and the number of datasets used, parametrizing the sensor offsets and factors, leads to model with over 100 parameters. With a real-time solution of the problem in mind, a highly efficient analytical variational Bayesian approach is used to solve it within seconds. An analysis of the required assumptions and limitations of the approach, especially w.r.t. to the computed evidence, is provided by a comparison with dynamic nested sampling in a simplified problem.
Finally, by inferring the value of additional damage parameters along the bridge, the method is successfully used to detect the location of an artificially introduced weak spot in the demonstrator bridge.
Concrete is a complex material and can be modeled on various spatial and temporal scales. While simulations on coarse scales are practical for engineering applications, a deeper understanding of the material is gained on finer scales. This is at the cost of an increased numerical effort that can be reduced by the three methods developed and used in this work, each corresponding to one publication.
The coarse spatial scale is related to fully homogenized models. The material is described in a phenomenological approach and the numerous parameters sometimes lack a physical meaning. Resolving the three-phase mesoscopic structure consisting of aggregates, the mortar matrix and the interfaces between them allow to describe similar effects with simpler models.
The quality of a model - and thus its predictive capabilities - is influenced by numerous uncertainties. They include possibly unknown boundary and initial conditions, noise in the data used for its calibration and uncertainties in the model itself. Here, the latter part is not only restricted to uncertain model parameters, but also refers to the choice of the model itself. Inferring these uncertainties in an automatic way allows for an adaption of the model to new data sets and for a reliable, reproducible model assessment. Note that similar concepts apply at the structural level, where a continuously updated digital twin allows virtual measurements at inaccessible positions of the structure and a simulation based lifetime prediction.
This work presents an inference workflow that describes the difference of measured data and simulated model responses with a generic interface that is independent from the specific model or even the geometry and can easily incorporate multiple data sources. A variational Bayesian inference algorithm is then used to a) calibrate a set of models to given data and to b) identify the best fitting one. The developed concepts are applied to a bridge Demonstrator equipped with displacement sensors, force sensors and a stereophotogrammetry system to perform a system identification of the material parameters as well as a real-time identification of a moving load.
Fatigue models that accurately resolve the complex three-dimensional failure mechanisms of concrete are numerically expensive. Especially the calibration of fatigue parameters to existing Wöhler lines requires solving for thousands or millions of cycles and a naive cycle-by-cycle integration is not feasible.
The proposed adaptive cycle jump methods provide a remedy to this challenge.
They greatly reduce the numerical effort of fatigue simulations and provide the basis for a development of those models.
One of the main challenges regarding our civil infrastructure is the efficient operation over their complete design lifetime while complying with standards and safety regulations. Thus, costs for maintenance or replacements must be optimized while still ensuring specified safety levels. This requires an accurate estimate of the current state as well as a prognosis for the remaining useful life. Currently, this is often done by regular manual or visual inspections within constant intervals. However, the critical sections are often not directly accessible or impossible to be instrumented at all. Model‐based approaches can be used where a digital twin of the structure is set up. For these approaches, a key challenge is the calibration and validation of the numerical model based on uncertain measurement data. The aim of this contribution is to increase the efficiency of model updating by using the advantage of model reduction (Proper Generalized Decomposition, PGD) and applying the derived method for efficient model identification of a random stiffness field of a real bridge.”
Lifetime aspects including fatigue failure of concrete structures were traditionally only of minor importance. Because of the growing interest in maxing out the capacities of concrete, its fatigue failure under compression has become an issue. A variety of interacting phenomena such as e.g. loss of prestress, degradation due to chemical reactions or creep and shrinkage influence the fatigue resistance. Failure due to cyclic loads is generally not instantaneous, but characterized by a steady damage accumulation. Therefore, a reliable numerical model to predict the performance of concrete over its lifetime is required, which accurately captures order effects and full three-dimensional stress states.
Many constitutive models for concrete are currently available, which are applicable for specific loading regimes, different time scales and different resolution scales.
However, a key limitation of those models is that they generally do not address issues related to fatigue on a structural level. Very few models can be found in the literature that reproduce deterioration of concrete under repeated loading-unloading cycles. This is due to the computational effort necessary to explicitly resolve every cycle which exceeds the currently available computational resources. The limitation can only be overcome by the application of multiscale methods in time.
The objective of the paper is the development of numerical methods for the simulation of concrete under fatigue loading using temporal multiscale methods.
First, a continuum damage model for concrete is developed with a focus on fatigue under compressive stresses [1]. This includes the possibility to model stress redistributions and capture size effects. In contrast to cycle based approaches, where damage is accumulated based on the number of full stress cycles, a strain based approach is developed that can capture cyclic degradation under variable loading cycles including different amplitudes and loading frequencies. The model is designed to represent failure under static loading as a particular case of fatigue failure after a single loading cycle. As a consequence, most of the material parameters can be deduced from static tests. Only a limit set of additional constitutive parameters is required to accurately describe the evolution under fatigue loading. Another advantage of the proposed model is the possibility to directly incorporate other multi-physics effects such as creep and shrinkage or thermal loading on the constitutive level.
Second, a multiscale approach in time is presented to enable structural computations of fatigue failure with a reduced computational effort. The damage rate within the short time scale corresponding to a single cycle is computed based on a Fourier based approach [2]. This evolution equation is then solved on the long time scale using different implicit and explicit time integration schemes. Their performance and some limitations for specific loading regimes is discussed.
Finally, the developed methods will be validated and compared to experimental data.
[1] Vitaliy Kindrachuk, Marc Thiele, Jörg F. Unger. Constitutive modeling of creep-fatigue interaction for normal strength concrete under compression, International Journal of Fatigue, 78:81-94, 2015
[2] Vitaliy Kindrachuk, Jörg F. Unger. A Fourier transformation-based temporal integration scheme for viscoplastic solids subjected to fatigue deterioration, International Journal of Fatigue, 100:215-228, 2017
Numerical simulators, such as finite element models, have become increasingly capable of predicting the behaviour of structures and components owing to more sophisticated underlying mathematical models and advanced computing power. A common challenge lies, however, in calibrating these models in terms of their unknown/uncertain parameters. When measurements exist, this can be achieved by comparing the model response against measured data. Besides uncertain model parameters, phenomena like damage can give rise to further uncertainties; in particular, quasi-brittle materials, like concrete, experience damage in a heterogeneous manner due to various imperfections, e.g. in geometry and boundary conditions. This hardens an accurate prediction of the damaged behaviour of real structures that comprise such materials.
In this study, which draws from a data-driven approach, we use the force-version of the finite element model updating method (FEMU-F) to incorporate measured displacements into the identification of the damage parameters, in order to cope with heterogeneity. In this method, instead of conducting a forward evaluation of the model and comparing the model response (displacements) against the data, we impose displacements to the model and compare the resulting force residuals with measured reaction forces. To account for uncertainties in the measurement of displacements, we endow this approach with a penalty term, which reflects the discrepancy between measured and imposed displacements, where the latter is assumed as unknown random variables to be identified as well. A Variational Bayesian approach is used as an approximating tool for computing posterior parameters. The underlying damage model considered in this work is a gradient-enhanced damage model.
We first establish the identification procedure through two virtual examples, where synthetic data (displacements) are generated over a certain spatially-dense set of points over the domain. The procedure is then validated on an experimental case-study; namely a 3-point bending experiment with displacement measurements resulting from a digital image correlation (DIC) analysis.