Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (99)
- Vortrag (42)
- Beitrag zu einem Tagungsband (15)
- Beitrag zu einem Sammelband (11)
- Posterpräsentation (8)
- Buchkapitel (4)
- Sonstiges (2)
- Forschungsdatensatz (2)
Sprache
- Englisch (183) (entfernen)
Schlagworte
- AFM (10)
- Raman spectroscopy (7)
- Epoxy (6)
- Low energy electrons (6)
- Boehmite (5)
- Atomic force microscopy (4)
- Cement (4)
- DNA (4)
- Friction (4)
- Micropatterning (4)
Organisationseinheit der BAM
- 6 Materialchemie (37)
- 6.6 Physik und chemische Analytik der Polymere (37)
- 6.1 Oberflächen- und Dünnschichtanalyse (9)
- 6.5 Synthese und Streuverfahren nanostrukturierter Materialien (5)
- 5 Werkstofftechnik (4)
- 6.3 Strukturanalytik (3)
- 7 Bauwerkssicherheit (3)
- 7.4 Baustofftechnologie (3)
- 4 Material und Umwelt (2)
- 5.1 Mikrostruktur Design und Degradation (2)
Paper des Monats
- ja (1)
Eingeladener Vortrag
- nein (42)
Scanning force microscopy (SFM) has been used to assess the local mechanical properties of fibre-reinforced polymers. Using a sinusoidal displacement modulation (DM) and lock-in technique the method allows to characterize local viscoelastic properties with a high lateral resolution. The simultaneous measurement of the local electrical conductivity is proposed which facilitates the interpretation of the mechanical data. The investigation of cross-sections perpendicular to the axis of carbon fibres embedded in PPS delivers some information about the change in local stiffness within the interfacial region. As a first approach, assuming a single-exponential decrease in local stiffness along a radial line from fibre to polymer we find characteristic decay lengths which are distributed in a range between 20 and 80nm. Further, a modified DM-mode is proposed which is expected to provide a contrast enhancement of the signal which is related to local stiffness. This can be achieved by installing an additional feedback loop which keeps constant the amplitude of dynamic indentation (CDI-mode).
Laser ablation of single-crystalline indium phosphide (InP) was performed in air by means of linearly polarized Ti:sapphire femtosecond-pulses (800 nm, 130 fs, 10 Hz). As a result of the first laser pulses, several morphological changes (crater formation, rim formation, ripple structures and cones) were observed. These effects were explored using force modulation microscopy (FMM), a technique based on scanning force microscopy (SFM), allowing the simultaneous imaging of both topography and local stiffness at a high lateral resolution. The first laser pulse induces the formation of a protruding rim (height <20 nm, width ~300 nm) bordering the ablated crater. A Fourier-analysis of the multi-pulse generated topographies reveals the formation of wavelength-sized periodic ripples (modulation depth <100 nm) with an orientation perpendicular to that of the electric field vector of the laser radiation. Besides these morphological alterations, also material modifications were observed in the irradiated regions by means of the FFM technique. Within the ablated craters, local stiffness variations were found revealing an inhomogeneous material composition/structure as a consequence of the femtosecond pulse laser treatment.
The physical properties as well as the thickness of the interphase between polymer and reinforcing phase are generally expected to show a strong influence on the macroscopic mechanical properties of composite materials. In this study the scanning force microscope (SFM) has been applied for detecting stiffness gradients near the interface between copper and epoxide. In displacement modulation mode the load exerted by the tip is modulated sinusoidally by vibrating the normal position of the cantilever or the sample. The corresponding amplitude of dynamic cantilever bending is related to local surface stiffness. Thus, using the SFM, the local mechanical properties of the surface under investigation can be probed. When scanning the tip across the reinforcement/polymer interface, the polymeric interphasial zone can be identified with the observed stiffness gradient. For a commercial epoxide based on diglycidyl ether of bisphenol A (DGEBA) cured with an amine-containing hardener, a stiffness gradient was detected that could be fitted by a Gaussian profile typical for diffusional processes. The width of the stiffness gradient was 280 nm. The observation is discussed in terms of interface-induced segregation processes between resin and hardener, as well as heat conduction mechanisms that can occur during the exothermic curing reaction. Both mechanisms are diffusional in nature and, via the local network structure, are expected to show some influence on the local stiffness of the cured epoxy. Copyright © 2000 John Wiley & Sons, Ltd.
We present dynamic plowing nanolithography on polymethylmethacrylate films, performed with a scan-linearized atomic force microscope able to scan up to 250 μm with high resolution. Modifications of the surface are obtained by plastically indenting the film surface with a vibrating tip. By changing the oscillation amplitude of the cantilever, i.e., the indentation depth, surfaces can be either imaged or modified. A program devoted to the control of the scanning process is also presented. The software basically converts the gray scale of pixel images into voltages used to control the dither piezo driving cantilever oscillations. The advantages of our experimental setup and the dependence of lithography efficiency on scanning parameters are discussed. Some insights into the process of surface modifications are presented.
Antimony clusters of different shapes and dimensions have been obtained by evaporating antimony on graphite. The dependence of the shape and dimensions of the particles on the evaporation parameters (effective layer thickness, temperature, pressure) is discussed. A characterisation of the different structures is presented. In particular, the decoration of graphite steps is discussed. Clusters have been dislocated by means of dynamic plowing nanolithography, both in vector and in image pattern mode. The dependence of the energy needed to dislocate a cluster on its dimensions and position is discussed.
Beyond measuring the topography of surfaces, scanning force microscopy (SFM) has proved to be valuable both for mapping of various materials properties and for modifying surfaces via lithography techniques. Thus, SFM has gained relevance as a surface analysis technique as well as a tool for nanoscale engineering purposes. Different kinds of tip-sample interactions are exploitable, e.g. mechanical, thermal and electrical ones. Owing to its versatility, SFM has found plenty of applications in polymer science. Among others, the examples reported on in this review article encompass issues related to commodity polymers, various polymer-based composites, polymer blends, or ferroelectric polymers. For instance, stiffness imaging is elucidated as a technique for detecting interphases occurring in composites with inorganic fillers. The described applications are mainly related to mechanical and electrical tip-sample interactions. The respective fundamentals are outlined as well as some aspects of the measurement of materials contrasts. The presented techniques of nano-scale modification are a dynamical sort of plowing lithography and electrical poling, both performed by means of SFM-probes.