Filtern
Erscheinungsjahr
- 2024 (6)
- 2023 (9)
- 2022 (5)
- 2021 (10)
- 2020 (6)
- 2019 (8)
- 2018 (4)
- 2017 (13)
- 2016 (14)
- 2015 (5)
- 2014 (3)
- 2013 (7)
- 2012 (10)
- 2011 (6)
- 2010 (8)
- 2009 (6)
- 2008 (7)
- 2007 (8)
- 2006 (1)
- 2005 (8)
- 2004 (4)
- 2003 (19)
- 2002 (11)
- 2001 (9)
- 2000 (6)
- 1999 (15)
- 1998 (13)
- 1997 (14)
- 1996 (12)
- 1995 (9)
- 1994 (5)
- 1993 (4)
- 1992 (2)
Dokumenttyp
- Zeitschriftenartikel (106)
- Vortrag (99)
- Beitrag zu einem Tagungsband (20)
- Posterpräsentation (18)
- Beitrag zu einem Sammelband (13)
- Buchkapitel (4)
- Sonstiges (2)
- Forschungsdatensatz (2)
- Corrigendum (1)
- Preprint (1)
Sprache
- Englisch (189)
- Deutsch (77)
- Mehrsprachig (1)
Schlagworte
- AFM (11)
- Low energy electrons (7)
- Raman spectroscopy (7)
- Epoxy (6)
- Atomic force microscopy (5)
- Boehmite (5)
- DNA (5)
- Multiphoton lithography (5)
- Cement (4)
- Dosimetry (4)
Organisationseinheit der BAM
- 6 Materialchemie (46)
- 6.6 Physik und chemische Analytik der Polymere (46)
- 6.1 Oberflächen- und Dünnschichtanalyse (9)
- 6.5 Synthese und Streuverfahren nanostrukturierter Materialien (6)
- 5 Werkstofftechnik (4)
- 6.3 Strukturanalytik (3)
- 7 Bauwerkssicherheit (3)
- 7.4 Baustofftechnologie (3)
- 4 Material und Umwelt (2)
- 5.1 Mikrostruktur Design und Degradation (2)
Paper des Monats
- ja (3)
Eingeladener Vortrag
- nein (99)
Waste disposal of carbon nanotube (CNT) containing products is expected to be the most important pathway for release of CNTs into the environment. In the present work, the use of radiolabelled CNTs (14C-CNT) for polycarbonate polymer nanocomposites with 1 wt% 14C-CNT content allowed for the first time to quantify and differentiate the CNT release according to the type of impact along the materials' ageing history. After an initial exposure of the nanocomposite by solar-like irradiation, further environmental impacts were applied to composite material. They aimed at mimicking disposal site conditions that may induce further ageing effects and CNT release. This study included shaking in water, rapid temperature changes, soaking in humic acid solution as well as waste water effluent, and, finally, gentle mechanical abrasion. All ageing impacts were applied sequentially, both on pristine (control) and on solar-irradiated nanocomposites. All experiments were accompanied by absolute quantification of radioactive release as well as chemical and morphological analyses of the nanocomposite surfaces using infra-red (IR) spectroscopy, X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). The morphological analysis showed that spectral irradiation can uncover CNT networks on the outer nanocomposite surface layers by polymer degradation. After having subjected the solar-irradiated nanocomposite to all studied disposal site effect, the total radioactive release was quantified to amount to 64 mg CNT/m2, whereas only 0.8 mg CNT/m2 were found for the un-irradiated control sample. Solar degradation of polymers was thus found to significantly increase the propensity of the studied polymer nanocomposites to release CNTs during ageing effects at the product's end-of-life typical for disposal sites.
Mussel-inspired polydopamine (PDA) initiated a multifunctional modification route that leads to the generation of novel advanced materials and their applications. However, existing PDA deposition techniques still exhibit poor spatial control, have a very limited capability of micropatterning and do not allow to locally tune PDA topography. Herein, we demonstrate PDA deposition based on Multiphoton Lithography (MPL) that enables full spatial and temporal control with nearly total freedom of patterning design. Using MPL, we achieve 2D microstructures of complex design with pattern precision of 0.8 μm without the need of a photomask or stamp. Moreover, this approach permits adjusting the morphology and thickness of the fabricated microstructure within one deposition step, resulting in a unique tunability of materials properties. The chemical composition of PDA is confirmed and its ability for protein enzyme immobilization is demonstrated. This work presents a new methodology for high precision and complete control of PDA deposition, enabling PDA incorporation in applications where fine and precise local surface functionalization is required. Possible applications include multicomponent functional elements and devices in microfluidics or lab-on-a-chip systems.