Filtern
Dokumenttyp
- Zeitschriftenartikel (12)
- Vortrag (4)
- Beitrag zu einem Tagungsband (3)
- Posterpräsentation (3)
- Dissertation (1)
- Sonstiges (1)
- Forschungsbericht (1)
Schlagworte
- Hybrid mixtures (8)
- 20L-sphere (6)
- Ignition source (5)
- Safety characteristics (5)
- Hybrid Mixtures (4)
- Betonfahrbahndecke (3)
- Safety characteristics determination (3)
- Bitumen (2)
- Explodierender Draht (2)
- Exploding Wire (2)
Organisationseinheit der BAM
Paper des Monats
- ja (1)
Eingeladener Vortrag
- nein (4)
Acetylene pressure cylinders are widely used in the industrial sector for welding, flame cutting, or heating.
Sometimes during work, not only with acetylene cylinders, fires occur and in this case the risk of destruction increases and the behavior of such an exposed cylinder is unpredictable. The purpose of this study is to identify those critical conditions when acetylene cylinders burst and explode in fires. In the present study, acetylene cylinders were exposed to fire conditions. For this purpose, a woodpile as a source of fire was chosen, tested, and evaluated. In addition to the fire condition, this option guaranteed reproducibility and similar conditions for all tests. The individual cylinders were equipped with thermocouples measuring the shell temperature, and half of them were prepared in order to measure the temperatures inside the cylinder. An important factor was the measurement of the amount of pressure that was achieved during the destruction of the cylinder. For this purpose, a pressure transducer was attached to the outlet of the cylinder valve. Exposed to direct fire, they can explode in 10 min, which was confirmed. The critical pressure of 40 bar has been reached in 6 min, followed by destruction after 7 min in fire. Cylinders with internal thermocouples were destroyed when lower pressure was achieved. This confirms the fact that any change of the pressure cylinder affects the original properties. After the tests, the fragments of the selected cylinders were subjected to material tests. The results obtained in these tests are the main source of information for understanding the behavior of acetylene cylinders in fire and the possibility of increasing the safety of intervening rescue services in an emergency.
The article summarizes a short review of the literature focused on safety in the field of alternative energy sources. With an increasing orientation towards sustainable and renewable energy sources, new technologies will come to the fore. These facts must be demonstrated in occupational health and safety. Several studies focused on alternative energy sources are mentioned and show the trends for the future. Especially in the area of hydrogen and battery technologies, systems should pay attention to acquisitions as a normal part of our lives.
Safety research is essential for the acceptance of cleaner, efficient, and sustainable future.
Voraussetzung zur Aufklärung von Fugenbewegungen in hochbeanspruchten Verkehrsflächen aus Beton ist ein neues, innovatives und sensitives Sensorsystem, welches unter den Bedingungen der Autobahnpraxis schnell und sicher in entsprechend beanspruchte Bereiche installiert werden kann und in der Lage ist, stabile und hochaufgelöste Bewegungen in mehrere Raumrichtungen zu erfassen. Das durch die BAM neu entwickelte Sensorsystem ist geeignet, um direkt in die Betonfahrbahndecke integriert zu werden und sowohl über saisonale Messbereiche als auch in hoher Auflösung entsprechende Messwerte online zu erfassen und bereit zu stellen. Das für diesen Zweck entwickelte innovative Sensorsystem kann direkt in die Rollspur auf beiden Seiten der Fuge eingebaut werden und ist dafür ausgelegt, Lkw-Überfahrungen zu widerstehen. Es ist schnell und präzise genug, um die realen Bewegungen in allen drei Raumachsen in Echtzeit erfassen zu können. Dieser Forschungsbericht beschreibt das Funktions- und Wirkschema des Sensorsystems und seine Validierung im Labor- und Feldmaßstab. Dabei wird insbesondere auch die praxisgerechte Einbau- und Nutzungsmethodik vorgestellt. Auflösungsvermögen, Robustheit und Nutzerfreundlichkeit werden am Beispiel einer Konzeptstudie auf dem Testgelände DuraBASt erprobt. Es werden grundlegende Hinweise auf den dringlichen Bedarf einer gebrauchsgerechten Beschreibung des realen Verhaltens des Bauwerks Betonstraße identifiziert.
Die mit dem Sensorsystem gewonnenen Daten können eine Grundlage für die Konzeption einer performance-basierten Bewertung von Fugenfüllsystemen in Betondecken von Bundesautobahnen bieten. Sie sind geeignet, die Funktionsmechanismen der verschiedenen Betonfahrbahnkonstruktionen besser zu verstehen und zielgerichtet konstruktive und materialtechnische Optimierungen und Fortentwicklungen von Fugenkonstruktionen und Fugenfüllsystemen in gebrauchsbezogener Weise zu entwickeln. Durch weitere Datenerhebung, -fusion und -analyse können Instandsetzungsintervalle und Lebensdauerzyklen besser abgeschätzt und geplant werden.
Die zielgerichtete Weiterentwicklung von Bauteilen und Konstruktionselementen im Straßenbau hochbeanspruchter Verkehrswege unserer Infrastruktur (Bundesfernstraßen) erfordert spezielle, bauteiladaptierte technische Möglichkeiten/Sensorik zur Quantifizierung des Gebrauchsverhaltens. Bei Fugen in Verkehrsflächen stellen insbesondere langsam und schnell ablaufende Plattendeformationen infolge jahreszeitlicher und verkehrlicher Beanspruchungen maßgebende Beanspruchungszustände dar. Eine Quantifizierung dieser Einwirkungen hilft bei der Weiterentwicklung sowie auch bei der Bewertung optimierter technischer Lösungen. In Forschung kompakt 17/21 „Innovative Sensorik für Fugensysteme“ wird eine neuartige, robuste Lösung der BAM zur Datenerfassung und Bauwerksmonitoring von hochbeanspruchten Verkehrsflächen aus Beton vorgestellt.
SENSO JOINT - An innovative sensor system for a sustainable joint design of concrete pavements
(2020)
Inacceptable capability and durability of joint sealing systems but also inadequate traffic performance (noise emission; overrolling comfort) up to traffic safety aspects reflect the still enormous demand for data-based description of concrete pavements performance under heavy loading conditions. Especially the deformation behavior of concrete pavement slabs in the joint region in consideration of new pavement construction types and improved concrete mixtures meanwhile established but also under the steeply rising traffic loads is not sufficiently explored. To create a data basis for advanced design rules, evaluation methods and product standards - and with it to improve quality, durability and finally sustainability of pavements - an innovative 3-D sensor system SENSO JOINT adapted to german roadworking requirements and suitable for heavy-duty operating conditions was developed. The contribution introduced describes the development of an extensive technical solution based on the analysis of decisive loads, interactions and boundary conditions. Based on calibration data, results of laboratory testing and finally field-testing on different concrete pavement construction types the outcome of a multi-level evaluation process shall introduce the potential of the new sensor system.
There are several standardized ignition sources in use for the determination of explosion characteristics of gases, vapors and dusts. In the standards the ignition source is stated, but they vary in stating other characteristics like burning duration, energy or burning volume. Since heat is not visible under normal circumstances a Schlieren-Technique was used to make the full heating volume and not just the flames visible. While an earlier paper of the authors focused on the ignition energy and burning duration of four standardized ignition sources, this paper focuses on the initial igniting volume, the ratio between initial igniting volume and the test-vessel size and other phenomena that were observed with the Schlieren-Technique.
In the standards for the determination of safety characteristics of dusts an initial pressure difference of 400 mbar (all: abs) is applied, that increases to 1013 mbar to achieve a homogeneous dust-air mixture. Since the measuring equipment accuracy is given with ± 0,1 bar the initial pressure could range somewhere between 300 and 500 mbar and the pressure increase between 500 and 700 mbar, leading to a testing pressure of 800 to 1200 mbar.
This variation does not only affect the testing pressure but also the concentration of dust and the level of turbulence, leading to wrong values of Pmax, Kst and assigning them to wrong concentrations. When tests for hybrid mixtures are conducted there are more degrees of freedom leading to even higher variations. To overcome these variations a higher accuracy is demanded for hybrid mixture testing. Further, in this presentation four standardized ignition sources are presented.
For the determination of safety characteristics of gases, vapors and dusts different types of ignition sources are used in international standards and guidelines. Table 1 compares technical relevant ignition sources with their main features. The paper presents test results of a comparative calorimetric and visual study between four different types of ignition sources. The ignition procedures were analyzed visually with a high-speed camera and electric recordings. In addition to that, the influence of the electrode-orientation, -distance as well as ignition energy on the reproducibility of the exploding wire igniter was tested.
The exploding wire is already in use for standardized determination of safety characteristics of gases, first tests on the suitability of the exploding wire igniter for dust testing have been carried out by Scheid et al. Using the exploding wire, the ignition energy can be varied from 2 to 10 000 J (2 x 5 000 J) and thus it could be used for gases, vapors, dusts and hybrid mixtures. Moreover it can be used at high initial pressures and it is the only ignition source with an easily measurable ignition energy release. Furthermore, it does not introduce another chemical reaction into the system.
Finally, a proposal for a standard ignition source for explosion tests on hybrid mixtures is derived from the test results.
Zur Bestimmung sicherheitstechnischer Kenngrößen (STK) von hybriden Gemischen (Gemisch aus mindestens zwei brennbaren Phasen, wie z.B. Staub/Gas- oder Gas/Dampf-Gemisch) existieren bislang keine einheitlichen, genormten Prüfmethoden. Die Normen und Regelwerke zur Bestimmung der STK von einphasigen brennbaren Systemen (Staub, Gas, Dampf) unterscheiden sich teilweise erheblich. Beispielsweise sind in den jeweiligen Normen für Stäube, Gase und Dämpfe unterschiedliche Zündquellen und Zündenergien definiert. Des Weiteren unterscheiden sich die in den Normen definierten Prüfabläufe bei der Gemischherstellung. Bei der Entwicklung einer einheitlichen Norm für hybride Gemische muss der Einfluss dieser beiden Parameter ermittelt werden, um die Vergleichbarkeit mit den STK der einzelnen Komponenten Gas, Staub und Dampf gewährleisten zu können und bisherige Erkenntnisse zu hybriden Gemischen interpretieren und bewerten zu können.