Filtern
Dokumenttyp
Sprache
- Englisch (4)
Referierte Publikation
- ja (4)
Schlagworte
- Atomic force microscopy (4) (entfernen)
Organisationseinheit der BAM
Forcedisplacement curves have been acquired with a commercial atomic force microscope on thin films of poly(n-butyl methacrylate) on glass substrates. Different film thicknesses, from 10 up to 430 nm, were chosen to examine in detail the so called mechanical double-layer topic, i.e., the influence of the substrate on the determination of the mechanical properties of thin films. Taking advantage of the Hertz theory we calculated for all films the contact radius between tip and sample as a function of the applied load. Further Young's modulus of the samples was derived from the experimental data as a function of the applied load and, alternatively, of the deformation. The results of this analysis for 10 different film thicknesses were fitted with several half empirical equations proposed by several researchers. The focus of this work is to evaluate such existing half empirical theories for mechanical double-layers and to show the need for an alternative consistent approach.
Force–displacement curves have been acquired with a commercial atomic force microscope on thin films of poly(n-butyl methacrylate) on glass substrates in order to examine the so-called 'mechanical double layer' topic, i.e. the influence of the substrate on the mechanical properties of the film in dependence of the film thickness. The hyperbolic fit, a novel semi-empirical equation introduced in previous articles, has been further corroborated. The interpretation of this equation has been deepened, yielding a quantitative and demonstrative characterization of the mechanical properties of double layers. Provided that the Young's moduli of bulk polymer and substrate are measured from the deformation curves, this mathematical model permits to fit the deformationforce curves on the double layers and to determine the thickness of the polymer films in wide range (0200 nm).
We show that complex physical and chemical interactions between boehmite nanoparticles and epoxy drastically affect matrix properties, which in the future will provide tuning of material properties for further optimization in applications from automotive to aerospace. We utilize intermodulation atomic force microscopy (ImAFM) for probing local stiffness of both particles and polymer matrix. Stiff particles are expected to increase total stiffness of nanocomposites and the stiffness of polymer should remain unchanged. However, ImAFM revealed that stiffness of matrix in epoxy/boehmite nanocomposite is significantly higher than unfilled epoxy. The stiffening effect of the boehmite on epoxy also depends on the particle concentration. To understand the mechanism behind property alteration induced by boehmite nanoparticles, network architecture is investigated using dynamic mechanical thermal analysis (DMTA). It was revealed that although with 15 wt% boehmite nanoparticles the modulus at glassy state increases, crosslinking density of epoxy for this composition is drastically low.
Long-time behavior of surface properties of microstructures fabricated by multiphoton lithography
(2021)
The multiphoton lithography (MPL) technique represents the future of 3D microprinting, enabling the production of complex microscale objects with high precision. Although the MPL fabrication parameters are widely evaluated and discussed, not much attention has been given to the microscopic properties of 3D objects with respect to their surface properties and time-dependent stability. These properties are of crucial importance when it comes to the safe and durable use of these structures in biomedical applications. In this work, we investigate the surface properties of the MPL-produced SZ2080 polymeric microstructures with regard to the physical aging processes during the post-production stage. The influence of aging on the polymeric microstructures was investigated by means of Atomic Force Microscopy (AFM) and X-ray Photoelectron Spectroscopy (XPS). As a result, a time-dependent change in Young’s Modulus, plastic deformation, and adhesion and their correlation to the development in chemical composition of the surface of MPL-microstructures are evaluated. The results presented here are valuable for the application of MPL-fabricated 3D objects in general, but especially in medical technology as they give detailed information of the physical and chemical time-dependent dynamic behavior of MPL-printed surfaces and thus their suitability and performance in biological systems.