Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (10)
- Beitrag zu einem Tagungsband (4)
- Posterpräsentation (4)
- Vortrag (1)
- Sonstiges (1)
Schlagworte
- Aktive Thermografie (2)
- Image processing (2)
- Nb3Sn (2)
- Resonance testing (2)
- Stress-strain behavior (2)
- Superconducting (2)
- Superconducting magnet (2)
- Supraleiter (2)
- X-ray absorption tomography (2)
- X-ray diffraction (2)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (1)
A test campaign was launched to determine the mechanical properties of the High Luminosity-Large HadronCollider (HL-LHC) 11 T Nb3Sn magnet components. The results can be used to accurately represent the mechanical properties in finite elementmodels that predict the stress and strain distribution in these magnets. Particular attention is paid to anisotropic mechanical behavior of the different magnet materials. Static and dynamic test methods have been applied for determining elastic materials’ behavior, and highly accurate Young’s moduli are obtained with the nondestructive dynamic methods resonance and impulse excitation at ambient temperature and during in situ heat cycles.
The load-independent Vickers hardness (HV) of the individual phases in a non-reacted Nb3Sn
wire has been measured and the yield strength (YS) of the individual components estimated
from the HV values. The YS and tensile strength (Rm) of the composite wire are calculated
according the rule of mixtures (ROM). Calculated tensile properties are compared with tensile
test results that were obtained for the entire composite wire, for the wire after removal of the
Cu stabiliser and for single Nb-7.5wt.%Ta fibres.
The degradation mechanisms of state-of-the-art Nb-Ti/Cu superconductors are described, based on in-situ synchrotron X-ray diffraction measurements during heat treatment. A quantitative description of the Nb-Ti/Cu degradation in terms of critical current density, Cu stabiliser resistivity and mechanical composite strength is presented. In an applied magnetic field a significant critical current degradation is already observed after a 5-minute 400 °C heat treatment, due to variations of –Ti precipitate size and distribution within the Nb-Ti alloy filaments. A strong degradation of the strand mechanical properties is observed after several minutes heating above 550 °C, which is also the temperature at which the formation of Cu-Ti intermetallic phases is detected. Several minutes heating at 250 °C are sufficient to increase the RRR of the strongly cold work strands inside a Rutherford type cable from about 80 to about 240. Heating for several minutes at 400 °C does not cause a significant conductor degradation in self-field and, thus, leaves enough temperature margin for the electrical interconnection of Nb-Ti/Cu conductors with common low temperature solders.
The knowledge of the temperature-induced changes of the superconductor volume and of the thermomechanical behavior of the different coil and tooling materials is required for predicting the coil geometry and the stress distribution in the coil after the Nb3Sn reaction heat treatment. In this paper, we have measured the Young’s and shear moduli of the HL-LHC 11 T Nb3Sn dipole magnet coil and reaction tool constituents during in situ heat cycles with the dynamic resonance method. The thermal expansion behaviors of the coil components and of a free standing Nb3Sn wire were compared based on dilation experiments.
The elastic anisotropy caused by the texture in the Nb3Sn filaments of PIT and RRP wires has been calculated by averaging the estimates of Voigt and Reuss, using published Nb3Sn single crystal elastic constants and the Nb3Sn grain orientation distribution determined in both wire types by Electron Backscatter Diffraction. At ambient temperature the calculated Nb3Sn E-moduli in axial direction in the PIT and the RRP wire are 130 GPa and 140 GPa, respectively. The calculated E-moduli are compared with tensile test results obtained for the corresponding wires and extracted filament bundles.
Conventional indentation hardness measurements to obtain load independent Vickers hardness values for the different phases in multifilamentary superconducting (SC) wires are described. The concept of composite hardness is validated for a binary metalmatrix metalfilament NbTi/Cu composite wire. The tensile materials properties of the individual wire components are estimated from their indentation hardness. The potential and limitations of this approach are critically discussed, based on a comparison with ensile test results obtained for wires and extracted NbTi filaments.
Accelerator magnets that can reach magnetic fields well beyond the Nb-Ti performance limits are presently being built and developed, using Nb3Sn superconductors. This technology requires reaction heat treatment (RHT) of the magnet coils, during which Nb3Sn is formed from its ductile precursor materials (a “wind and react” approach). The Nb3Sn microstructure and microchemistry are strongly influenced by the conductor fabrication route, and by the Phase changes during RHT. By combining in situ differential scanning calorimetry, high Energy synchrotron x-ray diffraction, and micro-tomography experiments, we have acquired a unique data set that describes in great detail the phase and microstructure changes that take place during the processing of restacked rod process (RRP), powder-in-tube (PIT), and internal tin (IT) Nb3Sn wires. At temperatures below 450 ° the phase evolutions in the three wire types are similar, with respectively solid state interdiffusion of Cu and Sn, Cu6Sn5 formation, and Cu6Sn5 peritectic transformation. Distinct differences in phase evolutions in the wires are found when temperatures exceed 450 °C. The volume changes of the conductor during RHT are a difficulty in the production of Nb3Sn accelerator magnets. We compare the wire diameter changes measured in situ by dilatometry with the phase and void volume evolution of the three types of Nb3Sn wire. Unlike the Nb3Sn wire length changes, the wire diameter evolution is characteristic for each Nb3Sn wire type. The strongest volume increase, of about 5%, is observed in the RRP wire, where the main diameter increase occurs above 600 °C upon Nb3Sn formation.