Filtern
Dokumenttyp
Sprache
- Englisch (10) (entfernen)
Schlagworte
- Damping concrete (3)
- Polyurethane foam (3)
- Drop test (2)
- Dynamic (2)
- Material models (2)
- Parameter identification (2)
- Penetration (2)
- Strain rate (2)
- Strain rate sensitivity (2)
- Temperature dependency (2)
- Compression tests (1)
- Crushing test (1)
- Drop tests (1)
- Dynamic crushing characteristics (1)
- Fem (1)
- Finite element model (1)
- Finite elements (1)
- Guided drop tests (1)
- Hankinson's formula (1)
- Impact limiter (1)
- Impact loading (1)
- Lateral constraint (1)
- Limiter (1)
- Material model (1)
- Multiaxial stress state (1)
- Numerical simulation (1)
- Plasticity (1)
- Plasticity model (1)
- Rate dependency (1)
- Spruce (1)
- Spruce wood (1)
- Temperature sensitivity (1)
An extensive series of large deformation crushing tests with spruce wood specimens was conducted. Material orientation, lateral constraint and loading rate were varied. Regarding material orientation, a reduction in the softening effect and the general force level was observed with a higher fiber-load angle. A comparison with characteristics gained by application of Hankinson's formula showed discrepancies in compression strength and the beginning of the hardening effect. Lateral constraint of the specimens caused a multiaxial stress state in the specimens, which was quantified with the applied measuring method. Further, a higher force level compared to specimens without lateral constraint and significant hardening effect at large deformations resulted. Thus, the influence of a multiaxial stress state on the force level could be determined. An increase in the loading rate led to higher force levels at any displacement value and material orientation.
In drop test scenarios related to assessing and licensing the storage procedure of spent fuel and high active waste, the casks under examination are generally not equipped with impact limiters. Hence, the extent of mechanical stresses in case of an assumed handling accident is largely affected by the ground properties of the reception hall floor in the specific storage facility.
Unlike conventional brittle foundation materials, damping concrete performs quite well in such applications as it features high stiffness as well as high energy absorption due to the filler pore volume. However, its damping ability is not sufficiently exploited in current finite element (FE) calculations due to a lack of advanced material models for simulating its impact response. An implementation of qualified concepts that account for plastic, strain rate dependent behavior requires additional information that has to be provided by systematic test series.
BAM recently started a research project to generate such data, subsequently to develop and to improve numerical methods for the analysis of impact limiters and damping foundation material and thus to optimize safety assessment tools for the design of transport and storage casks. A major part of this research concerns dynamic compression tests of variably shaped specimens conducted at a servo hydraulic 1MN impact testing machine as well as at a BAM facility for guided drop tests. This presentation focuses 100mm damping concrete cubes deformed vertically at constant rates under different constraint conditions. For example, a special fitting jig was constructed to subject the specimens to multi-axial loading. Thereby a deformation of 60% could be applied.
Simulation was conducted by FE code ABAQUS based on material models Concrete damaged plasticity and Crushable foam which both allow defining rate sensitive nonlinear stress-strain relations in compression beyond the classic metal plasticity approach.
The numerical Simulation of transport and storage casks for radioactive waste in accidental scenarios requires adequate material models and input parameters for all relevant structural cask elements, the Impact foundation as well as possibly further components involved in the incident. They form the basis for reliable analysis of different loading situations allowing substituting, at least in parts, experimental investigations that are needed in safety Reports submitted for nuclear licensing procedures.
Hereby, the efficiency of the energy absorbing components, such as cask Impact limiters or equivalent structures placed onto or into the foundation of storage buildings, determine to a large extend
the performance and thus the design of the casks. The limiters, which are usually made of wood, polyurethane foam (PUF) or damping concrete, are subjected to Major plastic deformations, whose Distribution and magnitude strongly depend on loading speed, course and temperature.
Consequently, it is necessary to establish a systematic data basis and implement this information in advanced numerical material formulations in Order to enable finite element simulations to account for all relevant factors.
Experimental and numerical studies of shock absorbing materials for containers for radioactive waste
(2012)
Proper predictions of the behaviour of shock absorber materials are of utmost importance in safety assessments for licensing casks for transport and storage of highly active waste. After having identified significant discrepancies between numerical results and the actual response of polyurethane foam limiters subjected to accidental scenarios, a new research project ENREA was established by BAM. A major objective is to enhance and to develop advanced material models intended to simulate limiters under impact loading. They should account for all major factors influencing the load–deformation relationship like temperature, strain rate and specific stress state. The corresponding test program, applicable plasticity models, the overall parameter identification strategy based on local and global optimization techniques as well as experimental and numerical results are presented here in particular for closed cell foams.
Finite element analysis (FEA) has been carried out for investigation of damping concrete under different impact loading conditions with a built-in material model and damage criteria available in FEA code ABAQUS.
At first, all parameters for the selected material model had been derived from compression Tests of cubic specimens. After that, a validation was carried out with different static and dynamic penetration tests. Finally, a 5 meter real drop test with a 23 Mg cylindrical cask could successfully be simulated.
Mechanical loading conditions of transport and storage casks for radioactive materials in accidental scenarios are highly affected by the behavior of both: the impact limiters and the footing materials. To minimize potential damages during the handling of casks, a so called damping concrete is frequently used for the footings in interim nuclear facilities. It obtains its shock absorbing properties through admixing of polymer cells. For a comprehensive mechanical evaluation of casks, advanced material models are also needed for damping concrete. In order to characterize the mechanical properties and to develop numerical material models, penetration tests were carried out at different test facilities of BAM. The tests contain static and dynamic penetration tests on cubic specimen with an edge length of 100 mm as well as mortared specimen with a size of 240 x 240 x 50 cm³. Indenters with different geometries and diameters were used for these model-sized penetration tests. Subsequently a full-scale cylindrical cast-iron indenter with a diameter of 110 cm was dropped of 5 m height on a realistic damping concrete footing.
Polyurethane foam used as impact limiter material undergoes high plastic deformations, whereat the resulting stress-strain relations strongly depend on loading speed and temperature. This paper discusses the efforts necessary to develop a reliable numerical foam simulation model focussing on generation and implementation of temperature- dependent yield curves