Filtern
Erscheinungsjahr
Dokumenttyp
- Beitrag zu einem Tagungsband (37)
- Zeitschriftenartikel (17)
- Beitrag zu einem Sammelband (12)
- Vortrag (10)
- Posterpräsentation (3)
- Forschungsbericht (2)
- Buchkapitel (1)
Schlagworte
- Slab track (7)
- Structural health monitoring (7)
- Field tests (6)
- Ground vibration (6)
- Hammer impact (6)
- Automated operational modal analysis (5)
- Damage detection (5)
- Railway track (5)
- Resonance (5)
- Train passage (5)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (10)
This paper presents the continuous dynamic measurements of an aging prestressed box-beam bridge during the period from 2000 to 2013, which consists of dynamic properties and environmental/operational factors, as well as the Variation of the extracted health features after removing the environmental/operational effects. Firstly, the variations of frequency estimates, temperatures and traffic loads from 2000 to 2013 are described. Subsequently, correlation analysis between them indicates the nonlinear influences of the temperature on the frequency estimates. The Multiple Linear Regression (MLR) method is used to remove the environmental/operational effects and the health index is proposed by performing the Novelty Detection analysis of the residual errors. Finally, the variations of the health index may indicate clear structural modifications that can be also characterized by the long term monitoring of the dynamic strain in the prestressed cable.
An drei Straßenbrücken unterschiedlicher Länge und Bauart wurden vor Inbetriebnahme ambiente Schwingungsmessungen mit bis zu 350 Messpunkten durchgeführt, um auch höhere Eigenformen detaillierter zu ermitteln. An einer Eisenbahnbrücke der Strecke Hannover-Würzburg wurden bei Testzugfahrten mit definierten Geschwindigkeiten verschiedene Resonanzanregungen beobachtet. Dies wird mit dem Achsfolgespektrum des ganzen Zuges erklärt, wobei eher spezifische Frequenzauslöschungen als Resonanzanregungen maßgeblich sind.
A variety of isolation measures exists to reduce the vibration in the neighbourhood of railway lines. They can be roughly classified as elastic or stiffening systems. There are the following elastic elements, rail pads or resilient fixation systems between rail and sleeper, under sleeper pads or sleeper shoes under the sleepers, and ballast mats under the ballast. Stiffening systems (plates) are used as slab tracks, floating slab tracks, or mass-spring systems. In the EU project “Railway induced vibration abatement solutions (RIVAS)”, elastic under sleeper pads have been investigated. The dynamic behaviour of the track and the surrounding soil has been calculated by the combined finite-element boundary-element method in a systematic parameter study. It has been shown that the mitigation effect can be improved by soft under sleeper pads or by heavy sleepers. Consequently, such track elements (soft under sleeper pads and heavy sleepers) have been thoroughly investigated in laboratory tests to establish the static and dynamic parameters as well as their serviceability. Finally, field tests at and near railway tracks with and without under sleeper pads have been performed. To determine the reduction effect of the isolated track, the ground vibrations excited by trains or artificial sources have been measured. The soil properties at the different sites have also been measured so that the comparison of the isolated and un-isolated track can take into account possible differences of the soil parameters. The contribution shows how the different (numerical, laboratory and field) methods and results can be combined to achieve an improved mitigation solution with soft under sleeper pads and heavy sleepers for ballasted and slab tracks.
Measured train passages and hammer impacts in combination with track-soil calculation have been successfully used for the detection of damaged slab tracks. This approach is now extended to intact slab and ballast tracks. The vibrations of many tracks have been measured at several levels from rail, sleeper, track plate, base plate, base layer to the subsoil by velocity or acceleration sensors. The time histories have to be integrated once or twice to get the displacements. The displacement signals include an arbitrary time-dependent shift which must be eliminated or respected in the interpretation. On the other hand, the calculation of slab and ballast tracks have been done in frequency-wavenumber domain. The displacements along the track and the frequency-dependent compliance transfer functions can be calculated. The latter can be compared with the results of the hammer impacts on the track. The deformation of the track can be transformed to time histories for a whole train and compared to the measured train passages. Many slab (and ballast) tracks have been measured at different sites. The displacements of the tracks are presented, and the following parameters have been analysed in the measurement results: slab track vs. ballast track, different types of slab tracks, damaged slab tracks, different trains, switches at different measuring points, an elastic layer, the mortar layer, different soils at different places. The soil should have the dominant influence on the track-plate displacements. Slab and ballast track yield also big differences in maximum displacement and width of deformation. Some of the preceding aspects will be analysed in comparison of measurement and theory.
Measured train passages and hammer impacts in combination with track-soil calculation have been successfully used for the detection of damaged slab tracks. This approach is now extended to intact slab and ballast tracks. The vibrations of many tracks have been measured at several levels from rail, sleeper, track plate, base plate, base layer to the subsoil by velocity or acceleration sensors. The time histories have to be integrated once or twice to get the displacements. The displacement signals include an arbitrary time-dependent shift which must be eliminated or respected in the interpretation. On the other hand, the calculation of slab and ballast tracks have been done in frequency-wavenumber domain. The displacements along the track and the frequency-dependent compliance transfer functions can be calculated. The latter can be compared with the results of the hammer impacts on the track. The deformation of the track can be transformed to time histories for a whole train and compared to the measured train passages. Many slab (and ballast) tracks have been measured at different sites. The displacements of the tracks are presented, and the following parameters have been analysed in the measurement results: slab track vs. ballast track, different types of slab tracks, damaged slab tracks, different trains, switches at different measuring points, an elastic layer, the mortar layer, different soils at different places. The soil should have the dominant influence on the track-plate displacements. Slab and ballast track yield also big differences in maximum displacement and width of deformation. Some of the preceding aspects will be analysed in comparison of measurement and theory.
Inspection and maintenance contribute significantly to the lifetime cost of bridges. There is significant potential in using information obtained through structural health monitoring to update predictive models of the condition and performance of such structures, and thus ena-ble an improved decision-making regarding inspection and maintenance activities. Within the AISTEC project funded by the German Federal Ministry of Education and Research, we develop vibration-based structural health monitoring systems aimed at continuously provid-ing information on the structural condition of bridges. Environmental variations such as changing ambient temperatures can significantly influence the dynamic characteristics of bridges and thus mask the effect of structural changes and damages. It remains a challenge to account for such influences in structural health monitoring. To study the effect of ambient temperatures on the dynamic characteristics of beam structures, we monitor the vibration response of a reinforced concrete beam in the uncracked and cracked state at varying tem-peratures in a climate chamber. We postulate a set of competing parameterized probabilistic structural models, which explicitly account for the effect of varying ambient temperatures on the mechanical properties of the system. We then combine the information provided by the structural models with the information contained in the recorded vibration data to learn the parameters of the temperature-dependent structural models and infer the plausible state of the beam using Bayesian system identification and model class selection.
At the Bundesanstalt für Materialforschung und -prüfung (BAM) full scale specimens for nuclear transport and storage containers (casks) are tested for their structural integrity in a series of drop tests on the Test Site Technical Safety in Horstwalde, 50 km south of Berlin. These drop tests cause a major stress not only on the casks, but also on the steel tower structure of the test facility, itself. The load pattern makes the structure very interesting for detailed investigation. The focus of the monitoring lies on the bolted joints of the flange connections that are a typical connection for cylindrical elements if welding is technical or economical unfavorable. The definition of the monitoring takes was done by investigating the existing documents and inspection results accompanied by building an initial digital representation of the structure, consisting of two finite element (FE) models and a geometrical 3D point cloud representation. As a first step the structures behavior during static and dynamic loading was analyzed using measurement data and an updated numerical FE Model. The idea behind is to use models for a digital planning and operation/evaluation of the structural health monitoring. A static FE simulation and a dynamic FE simulation are generated, to investigate how the structure behaves under the load conditions.
The dynamic behaviour of slab and ballast tracks has been investigated by measurements and calculations. Hammer impacts and train passages have been analysed. Measurements have been performed by geophones (velocity transducers) which have been time-integrated to displacements. The calculations are done in frequency-wavenumber domain for multi-beam-on-continuous soil models. The characteristics of the different tracks and track elements have been established in theory and experiment. The frequency-dependent compliances (displacement transfer functions) show clear rail-on-rail-pad resonances or highly damped track-soil resonances. Compared to the rail and sleeper, the track plate has much lower amplitudes. The slab track has usually the highest rail amplitudes due to soft rail pads. The train passage yields track displacements which are a superposition of the axle loads from the two neighbouring axles of a bogie and from the two bogies of two neighbouring carriages. This global behaviour is characteristic for the track plate of the slab track whereas the rails of the slab and the ballast track behave more local with only one bogie of influence. The measurements agree very well with the theory of the continuous soil in case of the six measured slab tracks and acceptably well for the six measured ballast tracks. The measurements allow to find appropriate model parameters and to check the models, for example the Winkler model of the soil has been found less appropriate as it reacts more locally.
A strain-based automated operational modal analysis algorithm is proposed to track the long-term dynamic behavior of a horizontal wind turbine under operational conditions.
This algorithm is firstly validated by a scaled wind turbine model, and then it is applied to the dynamic strain responses recorded from a 5 MW wind turbine system. We observed variations in the fundamental frequency and 1f, 3f excitation frequencies due to the mass imbalance of the blades and aerodynamic excitation by the tower dam or tower wake. Inspection of the Campbell diagram revealed that the adverse resonance phenomenon and Sommerfeld effect causing excessive vibrations of the wind tower.
Anhand verschiedener Bespiele wird diskutiert, wie Temperaturbeanspruchungen in einer Bauwerksüberwachung sichtbar werden und wie sie zu bewerten sind. Insbesondere der Einfluss auf die Zustandsbewertung im Sinne der Standsicherheit stellt häufig eine große Schwierigkeit dar. Behelfsweise besteht eine grundlegende Möglichkeit darin, ein Tragwerk immer zu seiner schwächsten Phase, d.h. in der Regel im Sommer zu beurteilen. Wie aufgezeigt, können zudem statistische Verfahren geeignet sein, Tragfähigkeitsänderungen zu detektieren.
Als wesentliche Zukunftsaufgaben werden verbesserte Detektionsalgorithmen und physikalisch begründete Modelle zum mechanischen Verhalten angesehen.
Die Akzeptanz schwingungsbasierter Verfahren zur Detektion und Lokalisierung von Schäden in der praktischen Anwendung ist alleinig von der Fähigkeit abhängig, Einflüsse aus veränderlichen Umwelt- und Betriebsbedingungen, insbesondere aber die aus der Temperatur zu eliminieren. Da die in den letzten Jahren immer wichtiger werdenden stochastischen Verfahren zur Schadensde-tektion und -lokalisierung die (statistische) Charakteristik der Messdaten bereits implizit nutzen, sind hier Entwicklung, Anpassung und Anwendung statistischer Algorithmen zur Eliminierung der variierenden Umwelteinflüsse naheliegend.
Auf der anderen Seite wird der saisonale Einfluss auf Bauwerksmessungen in sehr vielen Veröf-fentlichungen dargestellt und es werden häufig verdachtsweise begründete physikalische Zu-sammenhänge für das Verhalten aufgezeigt. Im Regelfall sind die Aussagen aber nicht experi-mentell überprüft und von eher allgemeiner Natur („Asphalt reagiert temperaturabhängig“). Ob-jektspezifische Zusammenhänge, beispielsweise über Versuch an Repräsentanten in der Klima-kammer ermittelt, könnten jedoch sehr hilfreich sein.