Filtern
Erscheinungsjahr
Dokumenttyp
- Beitrag zu einem Tagungsband (26)
- Zeitschriftenartikel (15)
- Beitrag zu einem Sammelband (6)
- Vortrag (5)
- Posterpräsentation (3)
- Buchkapitel (1)
Sprache
- Englisch (56) (entfernen)
Schlagworte
- Slab track (7)
- Field tests (6)
- Ground vibration (6)
- Hammer impact (6)
- Structural health monitoring (6)
- Automated operational modal analysis (5)
- Damage detection (5)
- Railway track (5)
- Resonance (5)
- Train passage (5)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (5)
The dynamic behaviour of slab and ballast tracks has been investigated by measurements and calculations. Hammer impacts and train passages have been analysed. Measurements have been performed by geophones (velocity transducers) which have been time-integrated to displacements. The calculations are done in frequency-wavenumber domain for multi-beam-on-continuous soil models. The characteristics of the different tracks and track elements have been established in theory and experiment. The frequency-dependent compliances (displacement transfer functions) show clear rail-on-rail-pad resonances or highly damped track-soil resonances. Compared to the rail and sleeper, the track plate has much lower amplitudes. The slab track has usually the highest rail amplitudes due to soft rail pads. The train passage yields track displacements which are a superposition of the axle loads from the two neighbouring axles of a bogie and from the two bogies of two neighbouring carriages. This global behaviour is characteristic for the track plate of the slab track whereas the rails of the slab and the ballast track behave more local with only one bogie of influence. The measurements agree very well with the theory of the continuous soil in case of the six measured slab tracks and acceptably well for the six measured ballast tracks. The measurements allow to find appropriate model parameters and to check the models, for example the Winkler model of the soil has been found less appropriate as it reacts more locally.
The Federal Institute of Material Research and Testing (BAM) has collected some experience with the testing of damaged, repaired and newly constructed railway tracks. The experimental methods are hammer testing of the track at different positions, hammer testing of the soil, measurement of train passages, and in all cases, measurements with geophones at different positions. The measured signals are evaluated for wave velocities (dispersion of the soil or the track-soil system), for transfer functions (transfer admittances of the soil, compliances of the track in amplitude and phase), and one-third octave band spectra of the track response to hammer and train excitation. These methods are applied at different stages of the track construction. Before track construction, wave velocities and transfer functions of the sub-soil can indicate problems with soft soils. After track construction, a check of the acceptable state of the track can be done by comparison of many excitation positions and track sites. After a track damage (a lose sleeper or a lose plate of a slab track) and after its repair, the sensitivity of the different measurement quantities to different track errors and the achieved improvement of the repair can be determined. The contribution shows examples of all these track situations.
The Federal Institute of Material Research and Testing (BAM) has collected some experience with the testing of damaged, repaired and newly constructed railway tracks. The experimental methods are hammer testing of the track at different positions, hammer testing of the soil, measurement of train passages, and in all cases, measurements with geophones at different positions. The measured signals are evaluated for wave velocities (dispersion of the soil or the track-soil system), for transfer functions (transfer admittances of the soil, compliances of the track in amplitude and phase), and one-third octave band spectra of the track response to hammer and train excitation. These methods are applied at different stages of the track construction. Before track construction, wave velocities and transfer functions of the sub-soil can indicate problems with soft soils. After track construction, a check of the acceptable state of the track can be done by comparison of many excitation positions and track sites. After a track damage (a lose sleeper or a lose plate of a slab track) and after its repair, the sensitivity of the different measurement quantities to different track errors and the achieved improvement of the repair can be determined. The contribution shows examples of all these track situations
In the context of national innovative project IMO-WIND, an integrated long term monitoring System was installed on a prototype of an offshore wind turbine System of 5 megawatt dass. The Federal Institute for Materials Research and Testing (BAM) was responsible for development of the SHM System. It consists of a signal acquisition System and a Signal processing and management System.
The signal acquisition System is composed of 14 acceleration sensors, 110 strain gauges and 4 inclination sensors, installed at the tripod foundation and the tower. It began to work in August 2007. In order to investigate the structural dynamic properties, extract efficient damage index and manage huge amounts of Vibration Signals and analysis results, an automated signal processing and management Software System is developed in LabVIEW® environment. It includes functions such as automated Operational Modal Analysis (OMA) on the basis of Stochastic Subspace Identification (SSI) method and poly-reference Least-Squares Complex Frequency Domain (p-LSCF) approach, investigation of environmental/operational effects on structural dynamic properties under operational conditions, features extraction using Principal Component Regression (PCR) and Multiple Linear Regression (MLR) as well as data/result management and visualization.
Besides, this paper also presents variations of structural modal parameters of a wind turbine system under complex environmental/operational conditions. Comparison of modal parameters automatically extracted by SSI method and poly-reference p-LSCF approach indicates that the latter method provides more stable modal identification results ffom the viewpoint of long term OMA. Subsequently, the influences of temperature, wind velocity, rotation speed and nacelle direction on modal parameters are generally discussed. Finally, variations of indentified modal parameters during two years are presented.
To ensure a high operational reliability of future generations of offshore wind conversion systems (OWEC) with economically acceptable repair and maintenance efforts, comprehensive diagnosis and supervision concepts are required. Automatic monitoring systems will be an essential part of such concepts. Because of the fact, that during operation there will be static and dynamic interaction between the components 'structure', 'machinery' and 'blades' it is necessary to develop the monitoring techniques in an overall concept. These monitoring systems are supposed to be applied for the design and testing as well as for the operation and maintenance phases. The used methods are focused on the design requirements for the structure, which are stated in the respective standards and certification guidelines. For the validation of the design, methods are specified which would be also applicable for SHM in the operating condition, e.g. for the evaluation of the structural conditon possibly after the occurrence of damages or changes. The further task consists in the realization of condition monitoring for all components, aiming at early damage detection and the observation of the damage development and its evaluation. Here the task consists of determining with assessment procedures the optimum time for maintenance actions to be carried out.