Filtern
Erscheinungsjahr
Dokumenttyp
- Beitrag zu einem Tagungsband (23)
- Zeitschriftenartikel (5)
- Vortrag (5)
- Posterpräsentation (2)
Sprache
- Englisch (35) (entfernen)
Schlagworte
- Radioactive material (8)
- Transport packages (8)
- Leakage rate (6)
- Safety assessment (6)
- Transport (5)
- Ageing (4)
- Seals (4)
- Spent fuel (4)
- Spent fuel assessment (4)
- Radioactive (3)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (5)
The mechanical and thermal loadings associated with the routine, normal and accident conditions of transport can have a significant effect on the leak tightness of the sealing system of transport casks for spent fuel and high radioactive waste.
Applicants are requested by BAM to provide test programmes for verification of design leakage rates of the sealing system under the possible loads.
Two test series initiated to clarify the dependency of the standard leakage rate on dynamic lid displacement as well as the dependency of the useful elastic recovery ru of a metallic seal on temperature and time, are outlined in this paper as examples of present investigations:
Sliding tests simulating a lid displacement possible by a horizontal drop of the cask are carried out at the controlled drop test facility of BAM with test flange pairs equipped with metallic Helicoflex seals.
For specification of covering values for the useful elastic recovery ru GNS has started a very comprehensive test programme with overall 70 metallic seals installed in test flanges which are stored for a period of one year at three different temperatures up to 150°C.
This paper gives an overview about the current approach of BAM in the assessment of cask tightness and informs about the status of the running test series.
Verification of activity release compliance with regulatory limits within spent fuel transport casks
(2010)
Admissible limits for activity release from type B(U) packages for spent fuel transport specified in the International Atomic Energy Agency regulations (10-6 A2 h-1 for normal conditions of transport and A2 per week for accidental conditions of transport) have to be kept by an appropriate function of the cask body and its sealing system. Direct measurements of activity release from the transport casks are not feasible. Therefore, the most common method for the specification of leak tightness is to relate the admissible limits of activity release to equivalent standardised leakage rates. Applicable procedure and calculation methods are summarised in the International Standard ISO 12807 and the US standard ANSI N14·5. BAM as the German competent authority for mechanical, thermal and containment assessment of packages liable for approval verifies the activity release compliance with the regulatory limits. Two fundamental aspects in the assessment are the specification of conservative design leakage rates for normal and accidental conditions of transport and the determination of release fractions of radioactive gases, volatiles and particles from spent fuel rods. Design leakage rates identify the efficiency limits of the sealing system under normal and accidental transport conditions and are deduced from tests with real casks, cask models or components. The releasable radioactive content is primarily determined by the fraction of rods developing cladding breaches and the release fractions of radionuclides due to cladding breaches. The influence of higher burn-ups on the failure probability of the rods and on the release fractions are important questions. This paper gives an overview about methodology of activity release calculation and correlated boundary conditions for assessment.
Requirements and test programs for sealed radioactive sources are specified in international standards for safety in transport and in use.
Sealed sources which are approved as special form radioactive material according to the Transport Regulations, IAEA Safety Standards TS-R-1, must be able to withstand mechanical (9 m drop, percussion and bending) and thermal (800°C heat) tests without loss of radioactive content.
The International Standard ISO 2919 provides a set of tests which classifies the sources for their safety in use. Performance tests specified in this standard are temperature (high and low), external pressure, impact, vibration and puncture tests. Each test can be applied at different levels of intensity depending on typical usage.
As a criterion of pass or fail, leakage testing has to be done after each test.
The poster gives an overview of BAM s comprehensive test equipment and experience in testing sealed radioactive sources.
Safety during whole life time: important aspect in safety assessment of sealed radioactive sources
(2008)
Many sealed sources with long halflife isotopes commonly used in industry or medicine have a long working life, up to several decades. Source integrity must be guaranteed in transport and use at any time. On the one hand, safety during the working life has to be ensured by the source design. Its strain has to be tested. On the other hand, source durability depends on the specific operating conditions. BAM as the competent authority in Germany has to assess the suitability of a source design for safe transport and use also for a longer service life for: (a) sources approved as special form radioactive material according to the regulations for the safe transport of radioactive material, (b) sources in approved devices for licence free use according to the Radiation Protection Ordinance, Para 25, and (c) sources with an extended leak test period according to Radiation Protection Ordinance, Para 66. In all these domains BAM has to assess if design and additional arrangements are qualified and guaranteed to prevent a release of radioactive content under the mechanical, chemical and physical operating conditions of the specified working life of a sealed radioactive source. As a result, limits for the duration of validity of the special form status of a source or a type approval of a device are specified and, in many cases, special additional responsibilities for users, such as periodical control and test measurements, have to be specified in approval certificates as binding conditions to satisfy the required safety standards in regulations. This paper presents BAM's experiences and shows which aspects should be considered in assessment of a lifetime limit of sealed sources.
With our experiments we want to simulate a load situation which can result from a cask vertical drop test. The lid can lift a little for a very short moment and that can perhaps result in a little movement of the seal, a little rotation or a little lateral movement, so that the contact section can change. The aim of the project is to learn more about the sealing efficiency after the seal is compressed again. What we know from former component tests with non-aged seals is, that the leakage rate measured after one or more decompression /compression cycles with seal movement becomes significant higher. And this result is considered for specification of design leakage rates for release calculation in safety cases.
In the recent years we all have learned more about the significant influence of temperature and time on seal behavior and so the plan was to do similar experiments with aged seals, just to get an idea about seal behavior and achievable leakage rates.
What we did in detail is:
We compressed Helicoflex-seals of both design types, with Aluminum and Silver outer jackets, in testflanges and aged them in an oven at a temperature of 125°C for 3 months to produce seal properties comparable with properties after several years use at more typical operating temperatures between 90 and 100°C.
After this ageing procedure we opened the flanges completely, moved the seal a little to vary the contact area and compressed the flanges again. What we measured during all compression and decompression cycles was the load, the deformation and -as long as possible- the leakage rates.