Filtern
Dokumenttyp
- Beitrag zu einem Tagungsband (5) (entfernen)
Sprache
- Englisch (5) (entfernen)
Schlagworte
- Leakage rate (3)
- Radioactive material (2)
- Containment (1)
- Leak tightness (1)
- Radioactive (1)
- Radioaktive (1)
- Safety (1)
- Safety assessment (1)
- Sealed sources (1)
- Sealing behavior (1)
Organisationseinheit der BAM
Requirements and test programs for sealed radioactive sources are specified in international standards for safety in transport and in use.
Sealed sources which are approved as special form radioactive material according to the Transport Regulations, IAEA Safety Standards TS-R-1, must be able to withstand mechanical (9 m drop, percussion and bending) and thermal (800°C heat) tests without loss of radioactive content.
The International Standard ISO 2919 provides a set of tests which classifies the sources for their safety in use. Performance tests specified in this standard are temperature (high and low), external pressure, impact, vibration and puncture tests. Each test can be applied at different levels of intensity depending on typical usage.
As a criterion of pass or fail, leakage testing has to be done after each test.
The poster gives an overview of BAM s comprehensive test equipment and experience in testing sealed radioactive sources.
The mechanical and thermal loadings associated with the routine, normal and accident conditions of transport can have a significant effect on the leak tightness of the sealing system of transport casks for spent fuel and high radioactive waste.
Applicants are requested by BAM to provide test programmes for verification of design leakage rates of the sealing system under the possible loads.
Two test series initiated to clarify the dependency of the standard leakage rate on dynamic lid displacement as well as the dependency of the useful elastic recovery ru of a metallic seal on temperature and time, are outlined in this paper as examples of present investigations:
Sliding tests simulating a lid displacement possible by a horizontal drop of the cask are carried out at the controlled drop test facility of BAM with test flange pairs equipped with metallic Helicoflex seals.
For specification of covering values for the useful elastic recovery ru GNS has started a very comprehensive test programme with overall 70 metallic seals installed in test flanges which are stored for a period of one year at three different temperatures up to 150°C.
This paper gives an overview about the current approach of BAM in the assessment of cask tightness and informs about the status of the running test series.
The containment systems of transport and storage casks for spent fuel and highlevelradioactive waste usually include bolted lids with metallic or elastomeric seals. The mechanical and thermal loadings associated with the routine, normal and accident conditions of transport can have a significant effect on the leak tightness of such containment system.
Scaled cask models are often used for providing the required mechanical and thermal tests series.Leak tests have been conducted on those models.
It is also common practice to use scaled component tests to investigate the influence of deformations or displacements of the lids and the seals on the standard leakage rate as well as to study the temperature and time depending alteration of the seals.
In this paper questions of the transferability of scaled test results to the full size design of the containment system will be discussed.
The design of a special form radioactive material has to resist a severe transport accident without undue loss or dispersal of radioactive material.
Safety assessment by authorities competent for design approval has to include besides the required test program (impact, percussion, bending and heat test) also the evaluation of the quality management system for design, manufacture, testing, documentation, use, maintenance and inspection.
These quality assurance measures have to assure that every specimen of the approved design is produced in the same verified quality and every specimen must be able to survive the severe mechanical and thermal tests without undue loss or dispersal of radioactive material at any time of its working life.
All important aspects in the design approval procedure by BAM as the competent authority for approvals of special form radioactive material in Germany are summarized in a guideline published in 2014. This paper will give additional explanations to some aspects in safety assessment, e.g.:
the applicability of leak test methods and the need to consider ageing aspects.
The containment systems of transport casks for spent fuel and high radioactive waste usually include bolted lids with metallic or elastomeric seals.
The mechanical and thermal loadings associated with the routine, normal and accident conditions of transport can have a significant effect on the leak tightness of such containment system.
Scaled cask models are often used for providing the required mechanical and thermal tests series. Leak tests have been conducted on those models.
It is also common practice to use scaled component tests to investigate the influence of deformations or displacements of the lids and the seals on the standard leakage rate as well as to study the temperature and time depending alteration of the seals.
In this paper questions of the transferability of scaled test results to the full size design of the containment system will be discussed.