Filtern
Erscheinungsjahr
Dokumenttyp
- Beitrag zu einem Tagungsband (19)
- Vortrag (5)
- Zeitschriftenartikel (4)
- Posterpräsentation (2)
Sprache
- Englisch (30) (entfernen)
Referierte Publikation
- nein (30) (entfernen)
Schlagworte
- Transport packages (8)
- Radioactive material (7)
- Leakage rate (5)
- Safety assessment (5)
- Transport (5)
- Ageing (4)
- Seals (4)
- Spent fuel assessment (4)
- Radioactive (3)
- Sealed sources (3)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (5)
German packages for the transport of spent nuclear fuel are assessed with respect to specific transport conditions which are defined in the safety regulations of the International Atomic Energy Agency.
In general, gastight fuel rods constitute the first barrier of the containment system. The physical state of the spent fuel and the fuel rod cladding as well as the geometric configuration of the fuel assemblies are important inputs for the evaluation of the package safety under transport conditions. The objective of this paper is to discuss the methodologies accepted by German authority BAM for the evaluation of spent fuel behavior within the package design approval procedure.
Specific test conditions will be analyzed with regard to assumptions to be used in the activity release and criticality safety analysis. In particular the different failure modes of the fuel rods, which can cause release of gas, volatiles, fuel particles or fragments, have to be properly considered in these assumptions.
The package as a mechanical system is characterized by a complex set of interactions, e.g. between the fuel rods within the assembly as well as between the fuel assemblies, the basket, and the cask containment. This complexity together with the limited knowledge about the material properties and the variation of the fuel assemblies regarding cladding material, burn-up and the operation history makes an exact mechanical analysis of the fuel rods nearly impossible.
The application of sophisticated numerical models requires extensive experimental data for model verification, which are in general not available. The gaps in information concerning the material properties of cladding and pellets, especially for the high burn-up fuel, make the analysis more complicated additionally, and require a conservative approach.
In this context some practical approaches based on experiences by BAM within safety assessment of packages for transport of spent fuel will be discussed.
Ongoing research activities to investigate SNF mechanical behavior in view of gas and fissile material release under transport loads are presented.
The mechanical and thermal loadings associated with the routine, normal and accident conditions of transport can have a significant effect on the leak tightness of the sealing system of transport casks for spent fuel and high radioactive waste.
Applicants are requested by BAM to provide test programmes for verification of design leakage rates of the sealing system under the possible loads.
Two test series initiated to clarify the dependency of the standard leakage rate on dynamic lid displacement as well as the dependency of the useful elastic recovery ru of a metallic seal on temperature and time, are outlined in this paper as examples of present investigations:
Sliding tests simulating a lid displacement possible by a horizontal drop of the cask are carried out at the controlled drop test facility of BAM with test flange pairs equipped with metallic Helicoflex seals.
For specification of covering values for the useful elastic recovery ru GNS has started a very comprehensive test programme with overall 70 metallic seals installed in test flanges which are stored for a period of one year at three different temperatures up to 150°C.
This paper gives an overview about the current approach of BAM in the assessment of cask tightness and informs about the status of the running test series.
Requirements and test programs for sealed radioactive sources are specified in international standards for safety in transport and in use.
Sealed sources which are approved as special form radioactive material according to the Transport Regulations, IAEA Safety Standards TS-R-1, must be able to withstand mechanical (9 m drop, percussion and bending) and thermal (800°C heat) tests without loss of radioactive content.
The International Standard ISO 2919 provides a set of tests which classifies the sources for their safety in use. Performance tests specified in this standard are temperature (high and low), external pressure, impact, vibration and puncture tests. Each test can be applied at different levels of intensity depending on typical usage.
As a criterion of pass or fail, leakage testing has to be done after each test.
The poster gives an overview of BAM s comprehensive test equipment and experience in testing sealed radioactive sources.
The design of a special form radioactive material has to resist a severe transport accident without undue loss or dispersal of radioactive material.
Safety assessment by authorities competent for design approval has to include besides the required test program (impact, percussion, bending and heat test) also the evaluation of the quality management system for design, manufacture, testing, documentation, use, maintenance and inspection.
These quality assurance measures have to assure that every specimen of the approved design is produced in the same verified quality and every specimen must be able to survive the severe mechanical and thermal tests without undue loss or dispersal of radioactive material at any time of its working life.
All important aspects in the design approval procedure by BAM as the competent authority for approvals of special form radioactive material in Germany are summarized in a guideline published in 2014. This paper will give additional explanations to some aspects in safety assessment, e.g.:
the applicability of leak test methods and the need to consider ageing aspects.
Acceptable limits for activity release from transport casks for high-level radioactive material specified in the IAEA regulations must be kept by the integrity of cask body and the cask sealing system. BAM as the German competent authority for mechanical, thermal and containment assessment of packages liable for approval verifies the activity release compliance with the regulatory limits. One of the fundamental aspects in assessment is the specification of conservative package design leakage rates.
To ensure the required package tightness for both, storage, and transport of the cask before and after storage usually metal seals of the Helicoflex® Type are used. Due to the long-term use the seal behavior is influenced by temperature and time. The mechanical and thermal loadings associated with the routine, normal and accident conditions of transport specified in the regulations can have a significant effect on the leak tightness of the sealing system. Whereas the safety for application of new, non- aged Helicoflex® seals is verified sufficiently, there are still technical data gaps concerning the efficiency of aged Helicoflex® seals.
BAM performed experiments to learn more about the sealing efficiency of aged Helicoflex® seals with Aluminum and Silver outer jackets. The seals were compressed in test-flanges and for artificial ageing the complete flange systems were stored in an oven for several month at a high temperature. During the compression and decompression tests after the aging, load-deformation characteristics of the seals, and leakage rates were measured. With these tests a load situation was simulated, which can occur in the regulatory drop test of the cask: Under high impact loads the bolted lid can lift a little for a short moment, allowing a little movement of the seal, so that the contact area can change before compressing again.
The poster presentation will show details about test conditions and first results.
In accordance with the IAEA transport regulations Special Form Radioactive Material (SFRM) is either an indispersible solid radioactive material or a sealed capsule containing radioactive material.
The design of special form radioactive material has to resist a severe transport accident without undue loss or dispersal of radioactive material. The safety assessment for design approval shall include besides the required test program (impact, percussion, bending and heat test) also the evaluation of the management system for design, manufacture, testing, documentation, use, maintenance and inspection. The specified quality assurance measures have to assure, that every specimen of the approved design is produced in the same verified quality and every specimen must be able to survive the severe mechanical and thermal tests at any time of its working life.
Due to the long-term use of SFRM the consideration of ageing is an important aspect in the approval procedure by BAM, the competent authority for SFRM approval in Germany. Different fields of application imply a wide range of environmental conditions, from clean room atmosphere to highly aggressive industrial conditions. So, besides of radioactive content, corrosion is a main factor for possible design degradation.
This paper will describe major influencing factors to be taken into account to assess the ageing behavior of a SFRM design and will emphasize that there is a need for a regulatory specification of a SFRM-working life as basis for the aging evaluations.
In accordance with the IAEA transport regulations, the design of special form radioactive material (SFRM) shall resist a severe transport accident without undue loss or dispersal of radioactive material. The safety assessment for design approval includes besides the program for physical tests (impact, percussion, bending and heat test) also the evaluation of the management system for design, manufacture, testing, documentation, use, maintenance, and inspection.
SFRM source design plus management system shall ensure, that every specimen of the approved design is able to survive the severe mechanical and thermal tests at any time of its SFRM-working life.
Due to the long-term use of SFRM designs in most cases, the assessment of the source ageing behavior is an important aspect in the approval procedure. Different fields of application imply a wide range of environmental conditions, from clean room atmosphere to highly aggressive industrial conditions. Besides of radioactive content, corrosion is a main factor for possible SFRM design degradation.
Although the IAEA Advisory Material SSG-26 already implies an indication of the need for considering ageing mechanisms, suitable amendments in the regulatory requirements of SSR-6 should be introduced to make the approval procedure more transparent and help to reduce rounds of questions by the authority. A supplementary requirement for considering of ageing mechanisms could be a helpful contribution to an international harmonization of the approval procedure.
This paper will describe major influencing factors to be considered to assess the ageing behavior of a SFRM design and will identify the need for a regulatory specification of a SFRM-working life as basis for the assessment of the SFRM design regarding time-dependent weakening. A proposal for an explicit requirement for consideration of ageing mechanisms in safety assessment of SFRM, which should be considered in the ongoing SSR-6 revision cycle, will be explained.
In accordance with the IAEA transport regulations, the design of special form radioactive material (SFRM) shall resist a severe transport accident without undue loss or dispersal of radioactive material. The safety assessment for design approval includes besides the program for physical tests (impact, percussion, bending and heat test) also the evaluation of the management system for design, manufacture, testing, documentation, use, maintenance, and inspection.
SFRM source design plus management system shall ensure, that every specimen of the approved design is able to survive the severe mechanical and thermal tests at any time of its SFRM-working life.
Due to the long-term use of SFRM designs in most cases, the assessment of the source ageing behavior is an important aspect in the approval procedure. Different fields of application imply a wide range of environmental conditions, from clean room atmosphere to highly aggressive industrial conditions. Besides of radioactive content, corrosion is a main factor for possible SFRM design degradation.
Although the IAEA Advisory Material SSG-26 already implies an indication of the need for considering ageing mechanisms, suitable amendments in the regulatory requirements of SSR-6 should be introduced to make the approval procedure more transparent and help to reduce rounds of questions by the authority. A supplementary requirement for considering of ageing mechanisms could be a helpful contribution to an international harmonization of the approval procedure.
This paper will describe major influencing factors to be considered to assess the ageing behavior of a SFRM design and will identify the need for a regulatory specification of a SFRM-working life as basis for the assessment of the SFRM design regarding time-dependent weakening. A proposal for an explicit requirement for consideration of ageing mechanisms in safety assessment of SFRM, which should be considered in the ongoing SSR-6 revision cycle, will be explained.