Filtern
Dokumenttyp
Sprache
- Englisch (12)
Schlagworte
- Safety assessment (3)
- Aging (2)
- Aging mechanisms (2)
- Corrosion (2)
- High burn-up (2)
- Metal seals (2)
- Radioactive (2)
- Radioactive material (2)
- Sealed sources (2)
- Spent fuel (2)
Transport packages for spent fuel have to meet the International Atomic Energy Agency requirements for different transport conditions. Physical state of spent fuel and fuel rod cladding as well as geometric configuration of fuel assemblies are important inputs for the evaluation of package capabilities under these conditions. In this paper, the mechanical behaviour of high burn-up spent fuel assemblies under transport conditions is analysed with regard to assumptions to be used in the activity release and criticality safety analysis. In particular the different failure modes of the fuel rods (fine cracks or complete breakage), which can cause release of gas, volatiles, fuel particles or fragments have to be properly considered in these assumptions. In view of the complexity of interactions between the fuel rods as well as between fuel assemblies, basket, and cask containment, the exact mechanical analysis of such phenomena is nearly impossible. The gaps in information concerning the material properties of cladding and pellets, especially for the high burn-up fuel, make the analysis more complicated additionally. In this context some practical approaches based on experiences of BAM Federal Institute for Material Research and Testing within safety assessment of packages for transport of spent fuel are discussed.
Admissible limits for activity release from type B(U) packages for spent fuel transport specified in the International Atomic Energy Agency regulations (10-6 A2 h-1 for normal conditions of transport and A2 per week for accidental conditions of transport) have to be kept by an appropriate function of the cask body and its sealing system. Direct measurements of activity release from the transport casks are not feasible. Therefore, the most common method for the specification of leak tightness is to relate the admissible limits of activity release to equivalent standardised leakage rates. Applicable procedure and calculation methods are summarised in the International Standard ISO 12807 and the US standard ANSI N14·5. BAM as the German competent authority for mechanical, thermal and containment assessment of packages liable for approval verifies the activity release compliance with the regulatory limits. Two fundamental aspects in the assessment are the specification of conservative design leakage rates for normal and accidental conditions of transport and the determination of release fractions of radioactive gases, volatiles and particles from spent fuel rods. Design leakage rates identify the efficiency limits of the sealing system under normal and accidental transport conditions and are deduced from tests with real casks, cask models or components. The releasable radioactive content is primarily determined by the fraction of rods developing cladding breaches and the release fractions of radionuclides due to cladding breaches. The influence of higher burn-ups on the failure probability of the rods and on the release fractions are important questions. This paper gives an overview about methodology of activity release calculation and correlated boundary conditions for assessment.
Safety during whole life time: important aspect in safety assessment of sealed radioactive sources
(2008)
Many sealed sources with long halflife isotopes commonly used in industry or medicine have a long working life, up to several decades. Source integrity must be guaranteed in transport and use at any time. On the one hand, safety during the working life has to be ensured by the source design. Its strain has to be tested. On the other hand, source durability depends on the specific operating conditions. BAM as the competent authority in Germany has to assess the suitability of a source design for safe transport and use also for a longer service life for: (a) sources approved as special form radioactive material according to the regulations for the safe transport of radioactive material, (b) sources in approved devices for licence free use according to the Radiation Protection Ordinance, Para 25, and (c) sources with an extended leak test period according to Radiation Protection Ordinance, Para 66. In all these domains BAM has to assess if design and additional arrangements are qualified and guaranteed to prevent a release of radioactive content under the mechanical, chemical and physical operating conditions of the specified working life of a sealed radioactive source. As a result, limits for the duration of validity of the special form status of a source or a type approval of a device are specified and, in many cases, special additional responsibilities for users, such as periodical control and test measurements, have to be specified in approval certificates as binding conditions to satisfy the required safety standards in regulations. This paper presents BAM's experiences and shows which aspects should be considered in assessment of a lifetime limit of sealed sources.
Requirements and test programs for sealed radioactive sources are specified in international standards for safety in transport and in use.
Sealed sources which are approved as special form radioactive material according to the Transport Regulations, IAEA Safety Standards TS-R-1, must be able to withstand mechanical (9 m drop, percussion and bending) and thermal (800°C heat) tests without loss of radioactive content.
The International Standard ISO 2919 provides a set of tests which classifies the sources for their safety in use. Performance tests specified in this standard are temperature (high and low), external pressure, impact, vibration and puncture tests. Each test can be applied at different levels of intensity depending on typical usage.
As a criterion of pass or fail, leakage testing has to be done after each test.
The poster gives an overview of BAM s comprehensive test equipment and experience in testing sealed radioactive sources.
Transport packages for spent nuclear fuel have to be assessed with respect to specific transport conditions which are defined in the safety regulations of the International Atomic Energy Agency. In general, gastight fuel rods constitute the first barrier of the containment system. The physical state of the spent fuel and the fuel rod cladding as well as the geometric configuration of the fuel assemblies are important inputs for the evaluation of the package safety under transport conditions. The objective of this paper is to discuss the methodologies accepted by BAM for the authority assessment of spent fuel behavior within the package design approval procedure of German package designs. In particular, cracks or failures in the fuel rod cladding can occur under regulatory transport conditions. These defects can cause the release of gas, volatiles, fuel particles or fragments into the package cavity and have to be considered properly in the safety analysis. Another issue is the transport of defective fuel rods. One concept is to use special canisters which can be handled like fuel assemblies. This concept requires additional assessment concerning drying, sealing and the mechanical and thermal design of such canisters. The package as a mechanical system is characterized by a complex set of interactions, e.g. between the fuel rods within the assembly as well as between the fuel assemblies, the basket, and the cask containment. This complexity together with the limited knowledge about the material properties and the variation of the fuel assemblies regarding cladding material, burn-up and the operation history makes an exact mechanical analysis of the fuel rods nearly impossible. The simplified approaches to consider conservatively spent fuel behavior currently accepted by BAM are presented here.
Verification of activity release compliance with regulatory limits within spent fuel transport casks
(2010)
When storage of spent nuclear fuel or high level waste is carried out in dual purpose casks (DPC), the effects of aging on safety relevant DPC functions and properties have to be managed in a way that a safe transport after the storage period of several decades is capable and can be justified and certified permanently throughout that period. The effects of aging mechanisms (e.g. radiation, different corrosion mechanisms, stress relaxation, creep, structural changes and degradation) on the transport package design safety assessment features have to be evaluated. Consideration of these issues in the DPC transport safety case will be addressed. Special attention is given to all cask components that cannot be directly inspected or changed without opening the cask cavity, like the inner parts of the closure system and the cask internals, like baskets or spent fuel assemblies. The design criteria of that transport safety case have to consider the operational impacts during storage. Aging is not the subject of technical aspects only but also of intellectual aspects, like changing standards, scientific/technical knowledge development and personal as well as institutional alterations. Those aspects are to be considered in the management system of license holders and in appropriate design approval update processes. The paper addresses issues that are subject of an actual International Atomic Energy Agency TECDOC draft 'Preparation of a safety case for a dual purpose cask containing spent nuclear fuel'.