The quality and durability of bonded joints, coated systems and composites depend on various factors. Therefore effective quantitative tests to determine adhesive, bonding or composite strength are of great need for R&D and QC. In this paper a new measuring principle is described which uses the centrifugal force to generate the test load. By the geometry of the whole measurement set-up, the test specimen are supported from only one side, the influence of shear forces is avoided. The possibility to test up to eight samples in one measurement under identical testing conditions allows a high sample throughput.
A detailed description of the whole sample preparation procedure including pre-treatment is followed by the specification of the measuring protocol as well as result analysis. For each application area bonding strength of joints, adhesive strength of coated systems and internal strength of composite materials examples are presented.
Für Prüfungen in der Beanspruchung auf Zug zur Bestimmung der Haft- bzw. Klebfestigkeit bzw. in der Beanspruchung auf Druck zur Bestimmung der Härte wurden bisher Zug- bzw. Härteprüfmaschinen als Ein-Proben-Prüfungen verwendet. In der Beanspruchung auf Zug ist die Probe beidseitig, und um das Einleiten von Querkräften zu verhindern, oft doppeltkardanisch einzuspannen. In jedem Falle handelt es sich um Ein-Proben-Prüfungen. Bei der Zentrifugentechnologie kann mit der Zentrifugalkraft als Prüfkraft unter Verwendung eines Trommelrotors erstmals in einer Mehr-Proben- Anordnung gearbeitet werden. Da die Proben nur einseitig unterstützt werden, ist die Beladung über einfaches Einstecken realisierbar.
Mit dem Auf-Tisch-Prüfsystem können bis zu acht Proben gleichzeitig auf Zug oder Druck beansprucht werden. Ein aufgeklebter oder anderweitig mit dem Prüfkörper verbundener und unter Einwirkung der Zentrifugalkraft in einer Führungshülse radial nach außen laufender Prüfstempel beansprucht dann die Klebung, die Beschichtung oder den Verbund auf Zug bis zum Versagen. Im Augenblick des Abrisses wird ein positionscodiertes und drehzahlkorreliertes Signal gesendet und so die Bestimmung von Kleb-, Haft- bzw. Verbundfestigkeiten im Mehr-Proben-Versuch möglich. Analog beansprucht ein in einer Führungshülse radial innen an den Proben anliegender ggf. mit entsprechenden Eindringkörpern ausgerüsteter nach außen gerichteter Prüfstempel die Proben auf Druck.
Aus Drehzahl, Radius und Prüfstempelmasse können dann Kleb-, Haft- bzw, Verbundfestigkeiten oder aber Brinell-, Kugeldruck- oder Vickers-Härtewerte bestimmt werden.
A new technology for strength determination of adhesive-bonded joints based on analytical centrifugatioon is introduced. Tensile as well as shear strength can be measured for multiple test specimens simultaneously within a very short time. The experimental procedure is described from sample preparation, application of adhesives, sample mounting within the centrifuge to testing parameters and sequences. All requirements of DIN EN 15870 are fulfilled and, in addition, a higher throughput and a better reproducibility can be obtained. The experimental results are discussed regarding bonding strength development over time, comparison of tensile and shear strength and various testing conditions. Furthermore, an additional application field of centrifuge technology is described with respect to the determination of the adhesive strength of coatings. The novel centrifuge based technology provides the determination of bonding, adhesive and shear strength on a statistical basis under identical testing conditions for up to eight samples. Moreover, sophisticated two-sided sample clamping, necessary for a tensile testing machine, is replaced by a simple plug-in procedure.