Filtern
Dokumenttyp
- Beitrag zu einem Sammelband (18) (entfernen)
Referierte Publikation
- nein (18)
Schlagworte
- Radar (6)
- Radiografie (6)
- Zerstörungsfreie Prüfung (6)
- Strukturaufklärung (5)
- Videoskopie (5)
- Baudenkmäler (4)
- Crack inspection (2)
- Crack overshoot (2)
- Digitale Radiologie (2)
- Laminografie (2)
Digital detectors such as phosphor imaging plates (IP) and digital detector arrays (DDA) allow radiographic inspection with higher efficiency and improved image quality in comparison to the classic film technique. Mobile X-ray flash tubes are used routinely for veterinarian and security applications. New high sensetive IPs and DDAs enable to apply them for inspection of light materials with low X-ray attenuation as in aluminium, plastics and composites. A versatile computed tompgraphy (CT) system was developed for in situ inspection of large aircraft components under production conditions. A gate based planar computed tomograph wsa developed and testes for inspection of integrety of the stringer incorporation. Successful test trials were performed to prove the detection rate of cracks in embedded stringers. Honey comb structures of aircrafts have to be inspected for water inclusions during in-service inspections. Thermography is a powerful method for in house inspections when variations in temperature caused e. g. by sunshine can be excluded. A new X-ray diaphragm was developed for mobile back scatter measurements of large components. This method is insensitive to heat alterations in the field and thus can be applied also outdoors.
Tomographical Computer Aided Radiology (TomoCAR) is based on the mechanical position control of
an X-ray tube in front of a welding seam and the application of a planar array detector behind it. Several hundred
radiometric projections in small angle steps are acquired. The tomographical reconstruction allows the three-dimensional
(3D) representation of the defects. A new radiometric array detector system with a small internal
unsharpness and high image contrast is used for the 2- and 3-dimensional visualization and sizing of planar defects
with a defect opening of less than 100 µm. This detector is based on a CMOS-flat panel with a direct converting
CdTe-single crystal layer. The small design allows the application of the mobile testing equipment for mechanized
X-ray inspection in industrial plants. The physical pixel size of the detector amounts to 0,1x0,1 mm². Nevertheless,
this system yields a better spatial resolution than indirect converting detectors (e.g. cameras with fluorescence
layers of Gd2O2S). It allows the reliable detection of planar defects with openings far below the detector pixel size
by subpixel resolution.
'TomoCAR' is qualified at present in the context with a German pilot study following to the ENIQ guidelines for
the employment within the nuclear power industry.
Zusammenfassung
Der Prototyp einer Flachröntgenröhre mit einer maximalen Röntgenenergie von 240kV (600W) und einer Brennfleckgröße von 0,4 * 0,4 mm nach DIN EN 12543 wird vorgestellt. Das Design dieser Flachröntgenröhre mit geringer Aufbauhöhe ist in Metall-Keramik-Technik ausgeführt. Die Beschleunigungsstrecke Katode-Anode ist senkrecht zur Haubenachse ausgeführt. Die Röhre ist als bipolares System aufgebaut. Kleine Durchmesser der Hochspannungskabel verringern das Gewicht und resultierende Kraftmomente bei der manuellen Manipulation sowie beim Verfahren in einem mechanisierten System. Der Targetwinkel beträgt 6° und bewirkt eine höhere Brillianz der Röntgenstrahlung. Die Geometrie des Strahlenaustrittsfensters (Emissionsfenster) ist in Fächerstrahlgeometrie zur tomografischen Prüfung ausgelegt.