Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (53) (entfernen)
Schlagworte
- ICP-MS (6)
- Reference material (6)
- HR-CS-MAS (4)
- AAS (3)
- CRM (3)
- Cadmium (3)
- Certified reference material (3)
- Graphite furnace (3)
- ICP-OES (3)
- Lithium (3)
Organisationseinheit der BAM
- 1 Analytische Chemie; Referenzmaterialien (22)
- 1.6 Anorganische Referenzmaterialien (20)
- 1.7 Organische Spuren- und Lebensmittelanalytik (5)
- P Präsident (4)
- P.0 Präsident und andere (4)
- 1.1 Anorganische Spurenanalytik (3)
- 1.2 Biophotonik (3)
- S Qualitätsinfrastruktur (3)
- S.1 Qualität im Prüfwesen (3)
- 1.3 Instrumentelle Analytik (2)
Paper des Monats
- ja (1)
Reliable and efficient methods for detecting genetically modified organisms (GMOs) are essential for establishing an effective system for traceability all along the supply chain from seed producers to final consumers. The latter is especially meaningful in European Union and other countries where strict legislations on GMOs were set up. Performance of the methods used in laboratories around the world should be uniform, in order to obtain reliable and comparable results. Accreditation is a suitable system for harmonising procedures in each testing laboratory. In this paper, key elements for the accreditation of molecular biology methods for GMO detection according to ISO/IEC 17025 are described. The procedures described are also valuable for the accreditation of molecular methods for all laboratory diagnostics where qualitative and quantitative characterisation of nucleic acids is needed.
The special importance of the analysis of non-metals in high purity metals, which will serve as national standards for elemental analysis in Germany, is illustrated for oxygen and nitrogen. The typical range of the mass fraction of oxygen and nitrogen in these materials is below 10.MU.g/g, often close to 1.MU.g/g. The two methods applied at BAM for these measurements are classical carrier gas hot extraction (HE) and carrier gas hot extraction after activation with photons (PAA-HE). The approach, the methods and their advantages and limitations are discussed. Comparative results from the measurement of oxygen and nitrogen in Cu, Fe, Ga, Pb, Sn and W are presented. (author abst.)
The preparation and analysis of the oxygen mass fraction of three pure copper reference materials (BAM-379/1, BAM-379/2, BAM-379/3) intended for the calibration of spark emission spectrometry are described here. Data of homogeneity testing and round robin certification in collaboration with 12 independent laboratories from metalworking industry and research are reported. Problems with the establishment of traceability in this special case are discussed.
An intercomparison study of analytical methods for the determination of magnesium in low alloy steel
(2012)
In an intercomparison study three low alloy steel materials were analyzed on their content of the trace element Mg, and five different analytical techniques were used, namely spark-OES, inductively coupled plasma optical emission spectrometry (ICP-OES), inductively coupled plasma time of flight mass spectrometry (ICP-TOFMS), inductively coupled plasma quadrupole mass spectrometry (ICP-QMS), and glow discharge mass spectrometry (GD-MS). Solid steel discs were used for analysis with spark-OES and GD-MS. For the analyses with ICP-OES, ICP-TOFMS, and ICP-QMS steel chips were wet-digested in aqua regia, and the wet-digestion was performed either in polypropylene tubes placed in a heating block or in Teflon pressure vessels using a microwave assisted system. The Mg concentrations obtained for the three steel materials were: 2.0, 2.8, and 10.3 µg g-1, respectively, and the spread in results was acceptable, giving RSD values in the range of 2030%.
The certification of a boron carbide reference material for chemical composition is described. The mass fractions of 16 elements and two boron species are certified in an international interlaboratory comparison with 35 participating laboratories from six different countries. Beside chemical characterization the certification process includes homogeneity and stability testing of the candidate material boron carbide (type F360, 305M422). Details of the analytical methods used for chemical characterization and of the calculation of the uncertainties of the certified mass fractions are given. The new reference material ERM®-ED102 with certified mass fractions of 18 parameters (elements and species) and of the amount fraction of the isotope 10B is a valuable tool for laboratories working in the field of advanced ceramic materials analysis to improve their analytical results.
The capabilities of National Metrology Institutes (NMIs) and selected outside expert laboratories of determining the mass fractions of the main and minor elements Cu, Pb, Sn, Fe, and Ni in a lead-containing brass were assessed. This pilot study P76 was organized as an activity of the Inorganic Analysis Working Group of CCQM and was piloted by the Federal Institute for Materials Research and Testing (BAM). In total 12 laboratories (four NMIs and eight outside labs) submitted results, some of them more than one set of results per element. The laboratories were free to choose any analytical method they wanted to use for the analysis. Consequently various methods of measurement were employed: inductively coupled plasma optical emission spectrometry (ICPOES), inductively coupled plasma mass spectrometry (ICPMS), instrumental neutron-activation analysis (INAA), titrimetry, flame atomic-absorption spectrometry (FAAS), spectrophotometry (MAS), electrogravimetry, and gravimetric analysis. After testing for homogeneity within BAM, a certified reference material of lead-containing brass was used as test sample without informing the participants about the source of the material. The agreement of the results for all elements investigated was acceptable and mean values calculated from the results of all participants were close to the certified mass fractions of the CRM used as test sample. No statistically significant differences between the results of the NMIs and those of the non-NMIs could be observed.