Filtern
Dokumenttyp
- Beitrag zu einem Tagungsband (8) (entfernen)
Sprache
- Englisch (8)
Referierte Publikation
- ja (8) (entfernen)
Schlagworte
- Damping concrete (3)
- Simulation (3)
- Cask (2)
- Crushable foam material model (2)
- Damage (2)
- Drop test (2)
- Finite element method (2)
- Impact load (2)
- Cask handling accident (1)
- Concrete foundation (1)
The shock absorbing material damping concrete is for the foundation in dry interim storage facilities for radioactive waste in Germany. In case of a potential cask drop damping concrete minimizes the mechanical loads to the cask. In course of safety analyzes this accident scenario is considered by numerical simulations using the finite element method. To get reliable results of numerical simulations a suitable material model is needed to take the characteristics of damping concrete into account. Due to the lack of sufficient material knowledge a research project was started to characterize the material’s behavior under different load conditions. This paper presents the test program to analyze the material behavior of damping concrete which is characterized by large volume change and
strain rate hardening dependence. The determined Parameters were used to adapt an existing material model of the FE-code ABAQUS®. This model has to handle the mechanical damage behavior of damping concrete which occurs under compression and shear loads during a potential cask drop. To verify the material model numerical simulations are compared with dynamic penetration tests, which were conducted with specimens assembled similar to the real application of the damping concrete footings. The transferability of the material
model to a real accident scenario was verified by a drop test with a full-scale cask on a damping concrete footing.
Influence of impact angle and real target properties on drop test results of cubic containers
(2017)
Drop test scenarios with cubic containers without impact limiters at interim storage sites or in a final repository have been investigated by numerical simulations. An ideally flat drop is impossible to conduct as a free fall of a container even under laboratory conditions. Dynamic stresses and strains inside the container structure are sensitive to the impact angle. Even very small impact angles cause remarkable changes in the experimental or numerical results when a flat bottom or wall of a container hits a flat target. For drop tests with transport packages the International Atomic Energy Agency (IAEA) regulations define an essentially unyielding target. In contrast, potential accident scenarios for storage containers are derived from site-specific safety analyses or acceptance criteria in Germany. Each interim storage site or repository has a yielding or so-called real target with individual structural and material properties. The real target acts as a kind of impact limiter. A more conservative container design is required if the impact limiting effect of the target is not considered.
Damping concrete with high energy absorption capability consists of a cement matrix with embedded small polystyrene balls and is investigated experimentally and numerically under high static compression with and without clamping. A material model is derived which describes the fundamental effects of damping concrete like non-linear elastic-plastic behaviour, volume change, volume strain dependent hardening as well as shear failure with an adequate description of damage initiation and evolution. The suggested material model is validated by simulation of penetration tests.
The safety assessment of casks for radioactive material at interim storage facilities or in final repositories includes the investigation of possible handling accidents if clearly defined test conditions are not available from the regulations. Specific handling accidents usually are the drop of a cask onto the transport vehicle or the floor as well as the collision with the wall of the storage building or another cask. For such load cases an experimental demonstration of cask safety would be difficult. Therefore, numerical analyses of the entire load scenario are preferred. The lessons learnt from dynamic finite element analyses of accident scenarios with thick-walled cubical containers or cylindrical casks are presented. The dependency of calculation results on initial and boundary conditions, material models, and contact conditions is discussed. Parameter sets used should be verified by numerical simulation of experimentally investigated similar test scenarios. On the other hand, decisions have to be made whether a parameter or property is modeled in a realistic or conservative manner. For example, a very small variation of the initial impact angle of a container can cause significantly different stresses and strains. In sophisticated cases an investigation of simpler limit load scenarios could be advantageous instead of analyzing a very complicated load scenario.
The deformation and damage behaviour of damping concrete under impact loading conditions is investigated experimentally and numerically. The material model is based on the assumption of crushable foam with volumetric or isotropic hardening combined with ductile and shear damage criteria. Model parameters are determined in static and dynamic compression tests of confined cubic specimens. The derived material model is validated by numerical simulation of penetration tests. The static and dynamic penetration of indenters into uniform as well as assembled bricks made of damping concrete is discussed. Finally, the successful calculation of a large-scale drop test with a heavy cask-like test object onto a realistic damping concrete foundation is demonstrated.
Cylindrical casks made of ductile cast iron are used for transport, interim storage and final disposal of radioactive waste in Germany. A basic design criterion is the ability to withstand a horizontal drop without impact Binders onto a foundation representative for the real ground of a storage facility. The increasing use of more cost-effective material compositions requires optimized cask geometries to reduce stresses and strains in the cask structure. For example, a non-uniform wall thickness was introduced to reduce maximum wall bending stresses. As a result, the load characteristics changed from line load to point load at bottom and lid side under horizontal drop fest conditions. Hereby, the position of highest stress inside the structure has shifted significantly. This was the reason for a systematic investigation of effects caused by small design changes or small variations of fest conditions. It led to a better understanding of the positions of high local stresses, their time history and maximum value for cylindrical casks under horizontal drop test conditions. Hence, the paper presents the lessons learnt from modeling and simulating such scenarios considering an impact without limiters onto a realistic target.
Validation of numerical simulation models for transport and storage casks using drop test results
(2012)
The safety assessment of new designs for transport and storage casks for radioactive materials is a challenging task accomplished using different methods such as prototype tests, model tests, calculations and analogy reflections. At BAM (Federal Institute for Materials Research and Testing), the test procedures for the mechanical IAEA (International Atomic Energy Agency) test conditions often start with preliminary finite element (FE) calculations mostly with a small-scale cask model for verification of the proposed test cask instrumentation and test plan. On that basis the extensive test cask instrumentation is applied and checked. After that, a series of drop tests consisting of different test sequences is performed.
Following the drop tests, numerical post-analyses are carried out. These analyses offer the possibility of a detailed calculation and assessment of stresses and strains in the entire test cask construction. The calculation results have to be carefully compared with the measurement data over the impact history to find out all relevant parameters for a realistic simulation of the impact scenario. The desired ideal boundary test conditions often cannot be met exactly during the drop tests. Therefore, the numerical post-analyses are carried out by using the real boundary conditions of the drop tests. The objective is to find a validated model, where the results of the numerical simulations satisfactorily meet the experimental results.
Under test conditions according to the IAEA transport regulations, casks are usually equipped with impact limiters and dropped onto a so-called unyielding target. In general, it is difficult to verify a complex FE model by using results from only one drop test because of the complex impact process and the complex structure of such packages. After each drop test, numerical post-analyses should be carried out. Only if all drop tests were simulated successfully by using the same FE model under different test conditions, it is possible to obtain a validated numerical model for further investigations. In this case the results of the numerical simulations meet satisfactorily the experimental results. In this paper a study is presented, where the influence of different components on the cask loading is investigated systematically.