Filtern
Erscheinungsjahr
Dokumenttyp
- Beitrag zu einem Tagungsband (25) (entfernen)
Referierte Publikation
- nein (25) (entfernen)
Schlagworte
- Fracture mechanics (5)
- Safety assessment (5)
- Behälterdesign (4)
- Container design (4)
- Drop test (4)
- Ductile iron (4)
- Duktiles Gusseisen (4)
- Dynamic loading conditions (4)
- Bruchmechanik (3)
- Dynamische Belastungsbedingungen (3)
Organisationseinheit der BAM
Practical methods for the safety assessment of postulated crack-like material defects of cubic containers made of ductile cast iron are presented. A formula for the stress intensity factor of a crack in a fillet with a radius from 20 to 200 mm under static load conditions is given. From that, an assessment diagram is derived for the critical depth of a crack in a fillet. The formula may be used to estimate the stress intensity factor of a dynamically loaded crack for special cases. As an application the results of the estimation procedure are compared with the results of a dynamic finite element calculation.
The safety of transport packages may be demonstrated by numerical calculation of load scenarios defined in the IAEA regulations. Possible handling accidents of casks at interim storage sites or in a final repository are typically analyzed by dynamic finite element computations. In each case the investigated load scenario must be transferred into a mathematical model. Secondly the mathematical model must be transferred into a numerical model. Reliable finite element models should be developed by assembling verified sub-models of components. The finite element mesh, material modeling, initial and boundary conditions, contact definitions, and time integration as well as the benefit of pre- and post-calculations are discussed. The paper presents lessons learnt from modeling dynamic test scenarios for finite element analyses over the years.
The 9 meter drop onto an unyielding target is one of the important mechanical tests within the safety assessment of transport casks for radioactive material. In general, the cask is equipped with impact limiters to reduce the dynamic load on the cask body by absorbing a major part of the kinetic energy. The impact limiters are often made of wood or aluminium. In this study an elastic-plastic material model with volume change was used to describe the stress-strain behaviour of wood found in crush tests. For aluminium, an elastic-incremental plastic material model with Cowper-Symonds parameters for strain rate depending material hardening was used to model the adiabatic stress-strain relations measured at specimens at constant ambient temperature. Hereafter simulations with a sophisticated finite element model were carried out and compared with different drop tests. Four drop tests of a half-scale cask model equipped with wood and aluminium impact limiters with different drop positions were selected to investigate the impact limiter behaviour during a 9 meter drop test. All drop tests were simulated with the same FE mesh but under different boundary and initial conditions.
Numerical simulation of 9 meter drop of a transport and storage cask with aluminium impact limiter
(2010)
For the purpose of numerical simulation of 9 meter drop of a transport and storage cask with aluminium impact limiter, an elastic-incremental plastic material model with strain rate hardening acc. to Cowper-Symonds is used for the development of isothermal as well as adiabatic stress-strain relations of aluminium from the compression test at constant ambient temperature. After that, two different simulation strategies are compared. At first, the drop test is calculated fully coupled, i.e. with isothermal stress-strain relations and possible heat generation in the material. Then the drop test is recalculated in a very simplified manner with adiabatic stress-strain relations from the compression test in an isothermal simulation. Both calculation strategies show similar results in the investigated load scenario.
Ermittlung dynamischer Kennwerte von Dämpferbeton für die Simulation des Beanspruchungsverhaltens
(2016)
Die Sicherheit und Integrität von Verpackungen radioaktiver Stoffe wird anhand von numerischen Berechnungen bewertet. Bei einem Anprall oder Absturz sind die mechanischen Beanspruchungen auf die Behälter auch von den Eigenschaften des Untergrunds abhängig. Um potentielle Gefahren während der Verladung zu minimieren, wird energieabsorbierender Dämpferbeton in den Handhabungsbereichen nuklearer Lager eingesetzt.
Zu einer umfassenden sicherheitstechnischen Analyse und Bewertung gehört die Berücksichtigung des Beanspruchungsverhaltens von Dämpferbeton. Hierfür ist ein numerisches Materialmodell notwendig, das in der Literatur bisher nicht vorlag. Die dafür notwendigen dynamischen Kennwerte sind in verschiedenen Druck- und Eindringversuchen ermittelt worden. Dazu wurden dynamische Druckversuche an würfelförmigen Prüfkörpern durchgeführt, sowie Eindringversuche mit unterschiedlichen Eindringkörpern und Dämpferbetonproben. Die experimentell ermittelten Kennwerte wurden verwendet, um ein Materialmodell für Dämpferbeton zu entwickeln und kritische Beanspruchungsszenarien numerisch zu berechnen. Um die Qualität des Materialmodells zu überprüfen, wurde ein realitätsnaher Fallversuch eines Behälters in Originalgröße auf ein lagertypisches Dämpferbetonfundament durchgeführt.
In dem Beitrag sollen die unterschiedlichen Untersuchungen zur Ermittlung dynamischer Kennwerte sowie deren Ergebnisse dargestellt werden. Gezeigt werden ebenso numerische Nachberechnungen einzelner Versuche sowie die ausführliche Berechnung des Fallversuchs im Originalmaßstab. Experimentelle und numerische Ergebnisse aus der Simulation werden hier gegenübergestellt.
The safety and integrity of casks for radioactive waste in accidental scenarios is analysed by BAM Federal institute tor Materials Research and Testing. An accidental scenario in German interim storage facilities is the drop from a crane during the handling operation. To reduce the mechanical loads to the cask a shock absorbing footing with high energy absorption capability is used in these areas. In order to analyse and evaluate such impact scenarios of casks, numerical simulations are performed. For a comprehensive simulation of an accidental scenario the behaviour of the damping concrete footing has to be taken into account as well and therefor a material model is needed. Material parameters under different loading conditions are the basis for a numerical model. For that reason a government funded research project (Kasparek, 2012) was conducted to characterise damping concrete under quasi-static as well as highly dynamic impact loading conditions. The performed tests include compression tests with and without lateral constraint small-scale and midscale penetration tests with different indenters, and finally a full-scale drop test onto a damping concrete footing.
The long-term sealing behavior of metal seals, assembled in the lid system of casks for transportation and storage of radioactive materials, has been investigated. For that purpose, phenomenological models describing the time- and temperature dependent behavior have been introduced by BAM since 2016, e.g. by using the time-temperature superposition principle. Results have shown that these models describe the relaxation behavior adequately and are suitable for extrapolations. In this work, the applicability of these models is checked by analyzing the necessary scope of tests, which must be carried out to get sufficient information about the long-term behavior of metal seals based on short-term tests.