Filtern
Erscheinungsjahr
Dokumenttyp
- Beitrag zu einem Tagungsband (49)
- Zeitschriftenartikel (28)
- Vortrag (4)
- Beitrag zu einem Sammelband (1)
- Posterpräsentation (1)
Sprache
- Englisch (83) (entfernen)
Schlagworte
- Guided waves (11)
- Lamb waves (10)
- Structural Health Monitoring (10)
- Dispersion (8)
- Ultrasound (8)
- Scaled boundary finite element method (7)
- Structural health monitoring (7)
- Non-destructive testing (6)
- Ray tracing (6)
- Ultrasonic testing (6)
Organisationseinheit der BAM
- 8 Zerstörungsfreie Prüfung (39)
- 8.4 Akustische und elektromagnetische Verfahren (39)
- 8.6 Faseroptische Sensorik (3)
- 2 Prozess- und Anlagensicherheit (2)
- 2.1 Sicherheit von Energieträgern (2)
- 3 Gefahrgutumschließungen; Energiespeicher (2)
- 3.2 Gefahrguttanks und Unfallmechanik (1)
- 3.5 Sicherheit von Gasspeichern (1)
- 8.1 Sensorik, mess- und prüftechnische Verfahren (1)
- 9 Komponentensicherheit (1)
Eingeladener Vortrag
- nein (4)
In this contribution a simulation tool is developed to compute the energy skewing angles and energy coefficients
for the reflected and refracted plane waves in following general cases: (1) reflection and refraction
of plane elastic waves at an interface between isotropic and transversely isotropic solid, (2) reflection
and refraction of plane elastic waves at an interface between transversely isotropic and isotropic solid, (3)
reflection and refraction of plane elastic waves at an interface between two general transversely isotropic
solid and (4) reflection of plane elastic waves from a stress free boundary of a transversely isotropic solid.
Computational results for analytically evaluated acoustic wave energy skewing angles and energy reflection
and transmission coefficients in acoustically anisotropic materials such as austenitic steel materials
exhibiting columnar grain orientation are presented. The obtained results show that the acoustic energy
skewing angles and coefficients in austenitic steel materials strongly depend upon the columnar grain
orientation and are less influenced by the grain orientations which are parallel and perpendicular to the
interface.
Lamb waves travel in plates and hollow cylinders over large distances and propagate with multiple mode shapes. Therefore the waves can be used for integrity tests of large scale structures. Each propagating wave mode has a unique dispersive character and a frequency dependent vibration pattern. Therefore, by interacting with flaws each mode is assumed to generate an individual reflection pattern depending on the flaw type, flaw orientation and size. To extract this information a frequency as well as wave number dependent mode excitation is required ensuring a single mode excitation. The challenge, however, is to control the selective mode excitation electronically to allow a sequence of consecutive tests with different wave modes to collect the data. A method is proposed using phased array wedge transducers with fluid coupling for normal force excitation of Lamb wave modes. The excitation principle is investigated analytically on plates by modelling the wave generation in the wedge and the coupling between wedge and structure. The analytical results of the excitation principle are validated by corresponding experiments where the field patterns on the wedge surface and on the plate were scanned using a laser vibrometer. The directivity of the radiated field is investigated together with the direction dependent analysis of the mode content.
This contribution describes a computationally efficient ray tracing algorithm for evaluating transducer generated ultrasonic wave fields in anisotropic materials such as austenitic cladded and austenitic weld components. According to this algorithm, ray paths are traced during its propagation through various layers of the material and at each Interface the problem of reflection and transmission is solved. The presented algorithm evaluates the transducer generated ultrasonic fields accurately by taking in to account the directivity, divergence, density of rays, phase relations as well as transmission coefficients. The ray tracing algorithm is able to calculate the ultrasonic wave fields generated by a point source as well as a finite dimension transducer. The simulation results are compared quantitatively with the results obtained from Elastodynamic Finite Integration Technique (EFIT) on several configurations generally occuring in the ultrasonic non destructive testing of anisotropic materials. The excellent agreement between both models confirms the validity of the presented ray tracing algorithm. Finally, the ray tracing model results are also validated by means of experiments.
In this study a method for early damage detection is investigated based on the directed excitation and measuring of Lamb waves (guided waves). The objective is to make a statement about the practicability of a Lamb wave generator (LWG) and about the application relevant parameters (specimen materials and dimensions, wave characteristics, excitation, transmission und reflection). Guided waves enable an effective differentiation of structural and defective indications as well as a classification of different defect types. For the investigations, a LWG was developed which combines the advantages of the single excitation of a piezoelectric actuator and the possibility of a group excitation. Algorithms were developed to identify and analyze damage patterns (cracks, wholes, weakening).
In this paper a numerical approach, based on the Scaled Boundary Finite Element Method (SBFEM), is described to obtain dispersion relations for propagating modes in wave guides. While the formulation is developed for plate structures, it can easily be extended to wave guides with arbitrary cross-section. The cross-section is discretized in the Finite Element sense while all equations remain analytical in the direction of propagation. The wave numbers of all propagating modes are obtained as the solutions of a standard eigenvalue problem. The group velocities can be calculated accurately as the eigenvalue derivatives. The use of higher-order elements drastically increases the efficiency and accuracy of the computation. This approach can be used for wave guides with arbitrary distribution of material parameters.
Up to now there is no sufficient technique to detect transverse cracks in austenitic and dissimilar welds which recently are of increasing interest in the integrity surveillance of nuclear power plants as well as in quality control of longitudinally welded pipes. Weld inspection by interpretation of single A-scans will lead to erroneous results due to effects caused by anisotropy and in worst case might leave flaws undetected. Therefore, imaging techniques such as the synthetic aperture focusing technique (SAFT) should be used. If the SAFT algorithm is applied on data taken from austenitic welds, the inhomogeneous, anisotropic structure of these welds has to be taken into account in order to properly attribute amplitudes measured in A-scans to the corresponding coordinates in the region of interest. While this has been investigated in the past, all attempts so far were limited to the imaging of longitudinal cracks which requires a less complicated setup than the imaging of transverse cracks. In this paper we give an outline of our attempts to reconstruct images of transverse cracks in different welds. For this purpose a SAFT program based on ray tracing and a layered structure weld model derived from an empirical model of grain orientations in welds are used. The results of the image reconstruction on experimental data are shown and compared to images obtained by assuming an isotropic homogeneous model. Root reflection and crack tip echo are clearly visible which allows an estimation of size and position of the crack with good accuracy.
Ultrasonic examination of anisotropic inhomogeneous austenitic welds is challenging, because of the columnar grain structure of the weld leads to beam skewing and splitting. Modeling tools play an important role in understanding the ultrasound field propagation and optimization of experimental parameters during the ultrasonic testing of austenitic welds as well as the interpretation of the test results. In this contribution, an efficient theoretical model based on the ray tracing concepts is developed to calculate the ultrasonic fields in inhomogeneous austenitic welds quantitatively. The developed model determines the ultrasound fields by taking into account the directivity of the ray source, the inhomogenity of the weld as well as ray transmission coefficients. Directivity of the ray source in columnar grained austenitic materials (including layback orientation) is obtained in three dimensions based on Lamb's reciprocity theorem. Ray energy reflection and transmission coefficients at an interface between two general columnar grained austenitic materials are calculated in three dimensions. The ray tracing model predictions on inhomogeneous austenitic weld material are compared against those from CIVA, a commercial non-destructive modeling and simulation tool. The ultrasonic modeling tools in CIVA are based on semi-analytical solutions. For beam propagation simulation, a so-called 'pencil method' is used, which involves modeling the probe as a set of individual source points, each radiating 'a bundle' of diverging rays into the medium and integrating those elementary contributions. Inhomogenity in the weld region is approximated by mapping the grain orientations on weld macrograph. Simulation results for ultrasonic field profiles for an austenitic weld are shown to be in good agreement with the corresponding experimental results.
Limited access to the object of relevance is often an essential problem in testing routines, e.g. for non-destructive testing of industry facilities or components of means of transportation. The presented project is about the development of a non-destructive testing method for application over great distances (up to 100 m). The method is based on directed excitation and measuring of Lamb waves (guided waves). It enables an effective differentiation of structural and defective indications as well as a classification of different defect types.
The advantage of guided waves is the ability of propagation over great distances. This offers innovative possibilities for the investigation of large or difficult to access constructions. The testing method can be helpful in a broad variety of applications. It is useable for the characterization of plane or cylindrical, thin-walled surfaces of metal or fiber laminated materials. Particularly the investigation of aircraft wings and other aerospace components as well as the investigation of pipelines are addressed fields of application.
In this contribution we present a novel thermo-acoustic approach for the generation of broad band airborne ultrasound and investigate the applicability of resonance-free thermo-acoustic emitters for very short high pressure airborne ultrasound pulses. We report on measurements of thermo-acoustic emitter consisting of a 30 nm thin metallic film on a usual soda-lime glass substrate, generating sound pressure values of more than 140 dB at 60 mm distance from the transducer and compare the results with conventional piezoelectric airborne ultrasound transducers. Our experimental investigations show that such thermo-acoustic devices can be used as broad band emitters using pulse excitation.