Filtern
Erscheinungsjahr
- 2021 (11) (entfernen)
Dokumenttyp
Schlagworte
- Inverse Probleme (3)
- Composites (2)
- Dispersion (2)
- Lamb waves (2)
- Materialcharakterisierung (2)
- Thermoplastische Kunststoffe (2)
- Ultraschall (2)
- Ultrasonic guided waves (2)
- Ultrasound (2)
- AD (1)
Organisationseinheit der BAM
An approach to adhesive bond characterisation using guided acoustic waves in multi-layered plates
(2021)
An approach for the non-destructive characterisation of adhesive bonds using guided ultrasonic waves is presented. Pulsed laser radiation is used to thermoacoustically excite broadband ultrasonic waves in a multi-layered sample, consisting of a metal plate adhesively joined to a polymeric layer using synthetic resin. The resulting signals are received by a purpose-built piezoelectric transducer. Varying the distance between excitation and detection yields spatio-temporal measurement data, from which the dispersive properties of the propagating waves can be inferred using a two-dimensional Fourier transform, assuming the plates to act as coupled waveguides. Coupled multi-layered waveguides show an effect referred to as mode repulsion, where the distance between certain modes in the frequency-wavenumber domain is assumed to be a measure of coupling strength. Measurements at different stages of curing of the adhesive layer are performed and evaluated. A comparison of the results shows changes in the dispersive properties, namely an increased modal bandwidth for the fully cured sample as well as an increased modal distance.
Бегущие упругие волны часто используются в области неразрушающего контроля для определения механических характеристик материалов. Поскольку склеивание различных материалов является широко используемым методом в автомобильной и авиационной промышленности, необходима надежная система измерения для определения качества таких клеевых соединений. Дисперсионные кривые для многослойных волноводов при наличии клеевых прослоек характеризуются появлением эффекта расталкивания нормальных мод в тех областях, где соответствующие моды для отдельных материалов пересекались бы. Таким образом, в зависимости от качества клеевого соединения расстояние между этими модами изменяется. Используя комбинацию экспериментальных и численных данных, в настоящей работе представлен подход к определению параметра, указывающего на качество клеевого соединения.
Detailliertes Wissen über die mechanischen Eigenschaften verwendeter Materialien ist Grundvoraussetzung für viele ingenieurtechnische Aufgaben und Dienstleistungen. Zur Bestimmung der elastischen Materialparameter gibt es verschiedene klassische, zerstörende Prüfverfahren. Eine Möglichkeit der zerstörungsfreien Bestimmung liegt in der Auswertung von Messergebnissen, die auf Basis des Ausbreitungsverhaltens geführter Ultraschallwellen gewonnen wurden. Das Ausbreitungsverhalten geführter Ultraschallwellen kann mittels Dispersionsabbildungen dargestellt werden.
Um aus messtechnisch ermittelten Dispersionsabbildungen Rückschlüsse auf die Materialparameter zu ziehen, werden in der aktuellen Forschung verschiedene inverse Methoden diskutiert. Maschinelles Lernen und insbesondere Convolutional Neural Networks (CNNs) stellen eine Möglichkeit der automatisierten inversen Modellierung und Evaluierung von Bilddaten dar.
In diesem Beitrag wird gezeigt, wie das Ausbreitungsverhalten von geführten Ultraschallwellen unter Verwendung von CNNs genutzt werden kann, um die isotropen elastischen Konstanten einer plattenförmigen Struktur zu bestimmen. Hierfür werden die verwendeten Daten analysiert, das Preprocessing erläutert und eine grundlegende CNN-Architektur gewählt. Zur Auswertung des generierten Modells werden verschiedene Verfahren wie Gradienten-Mapping und die Visualisierung der verschiedenen Schichten vorgestellt. Die Anwendbarkeit der Methode wird anhand synthetischer Daten demonstriert.
In the field of non-destructive testing, Lamb waves are often used for material characterisation. The increasing computational capabilities further enable complex and detailed simulations to predict the material behaviour in reality. Since adhesive bonding of different materials is a widely used method in modern applications, a reliable measurement system to determine the quality of these adhesive bonds is needed. Investigations of the dispersive behaviour of acoustic waves in adhesively bonded multi-layered waveguides show mode repulsions in the dispersion diagrams in regions where the modes of the single materials would otherwise intersect. In previous works, changes of the distance between those modes with respect to the bonding quality are observed. The experimental data for this investigation is generated using pulsed laser radiation to excite broadband acoustic waves in plate like specimens which are detected by a piezoelectric ultrasonic transducer. Numerical data is generated using simulations via a semi-analytical finite element method. Using a combination of experimental and numerical data, the present work introduces an approach to determine a parameter which indicates the bonding quality in relation
to an ideal material coupling.
Composite-overwrapped pressure vessels (COPV) are increasingly used in the transportation industry due to their high strength to mass ratio. Throughout the years, various designs were developed and found their applications. Currently, there are five designs, which can be subdivided into two main categories - with a load-sharing metal liner and with a non-load-sharing plastic liner. The main damage mechanism defining the lifetime of the first type is fatigue of the metal liner, whereas for the second type it is fatigue of the composite overwrap. Nevertheless, one damage type which may drastically reduce the lifetime of COPV is impact-induced damage. Therefore, this barely visible damage needs to be assessed in a non-destructive way to decide whether the pressure vessel can be further used or has to be put out of service. One of the possible methods is based on ultrasonic waves. In this contribution, both conventional ultrasonic testing (UT) by high-frequency bulk waves and wavenumber mapping by low frequency guided waves are used to evaluate impact damage. Wavenumber mapping techniques are first benchmarked on a simulated aluminium panel then applied to experimental measurements acquired on a delaminated aluminium-CFRP composite plate which corresponds to a structure of COPV with a load-sharing metal liner. The analysis of experimental data obtained from measurements of guided waves propagating in an aluminium-CFRP composite plate with impact-induced damage is performed. All approaches show similar performance in terms of quantification of damage size and depths while being applied to numerical data. The approaches used on the experimental data deliver an accurate estimate of the in-plane size of the large delamination at the aluminium-CFRP interface but only a rough estimate of its depth. Moreover, none of the wavenumber mapping techniques used in the study can quantify every delamination between CFRP plies caused by the impact, which is the case for conventional UT. This may be solved by using higher frequencies (shorter wavelengths) or more advanced signal processing techniques. All in all, it can be concluded that imaging of complex impact damage in fibre-reinforced composites based on wavenumber mapping is not straightforward and stays a challenging task.
In the context of Industry 4.0 and especially in the field of Structural Health Monitoring, Condition Monitoring and Digital Twins, simulations are becoming more and more important. The exact determination of material parameters is required for realistic results of numerical simulations of the static and dynamic behavior of technical structures. There are many possibilities to determine
elastic material parameters. One possibility of non-destructive testing are ultrasonic guided waves. For the evaluation of the measurement results, mostly inverse methods are applied in order to be able to draw conclusions about the elastic material parameters from analysing the ultrasonic guided wave propagation. For the inverse determination of the elastic material Parameters with ultrasonic guided waves, several investigations were carried out, e.g. the determination of the isotropic material parameters through the point of zero-groupvelocity or anisotropic material parameters with a simplex algorithm. These investigations are based on the evaluation of dispersion images. Machine learning and in particular Convolutional Neural Networks (CNN) are one possibility of the automated evaluation from Image data, e.g. classification or object recognition problems. This article shows how the dispersive behavior of ultrasonic guided waves and CNNs can be used to determine the isotropic elastic constants of plate-like structures.
Lamb waves are a common tool in the field of non-destructive testing and are widely used for materialcharacterisation. Further, the increasing computational capability of modern systems enables the Simulation of complex and detailed material models. This work demonstrates the possibility of simulating an adhesive-bonded multilayer system by characterising each layer individually, and introduces an Approach for determining the dispersive behaviour of acoustic waves in a multilayer system via real measurements.
Eine zentrale Aufgabe der zerstörungsfreien Prüfung und der Strukturüberwachung (engl. Structural Health Monitoring - SHM) mit Ultraschallwellen ist die Bewertung von Schäden in Bauteilen. In vielen Bauteilen, wie zum Beispiel platten- und schalenförmigen Strukturen, Rohrleitungen oder Laminaten, breitet sich der Ultraschall in Form geführter Wellen aus. Zwar haben geführte Wellen eine relativ große Reichweite innerhalb des Bauteils und ermöglichen so eine großflächige Prüfung, ihre multimodalen und dispersiven Eigenschaften erschweren jedoch die Analyse der vom Schaden kommenden Reflexionen. Eine Möglichkeit, die Messsignale zu interpretieren und die Schäden zu charakterisieren, ist deren Vergleich mit der Wellenausbreitung in einem digitalen Modell. Hierbei stellt sich die Aufgabe, den Schaden im digitalen Modell anhand der Messdaten zu rekonstruieren. Diese Rekonstruktion beschreibt ein inverses Problem, das mehrere Vorwärtsrechnungen braucht, um das Schadensmodell an die Messdaten anzupassen. Durch die kleine Wellenlänge von Ultraschallwellen sind klassische Vorwärtsmethoden wie die Finte Elemente Methode rechenintensiv, weshalb die Autoren die semi-analytische Scaled Boundary Finite Element Method (SBFEM) benutzen, um den Rechenaufwand zu verringern. Im Beitrag wird ein inverses Verfahren basierend auf dem Automatischen Differenzieren in Kombination mit der SBFEM vorgestellt und an verschiedenen Schadenstypen in 2D-Querschnittmodellen von Wellenleitern getestet. In der präsentierten Vorstudie werden dafür „Messdaten“ aus unabhängigen Simulationen verwendet.
The dispersive properties of Lamb waves can be utilised for material characterisation because the frequency-wavenumber-relationship, as well as the group velocity, depend on material parameters. These dependencies make a non-destructive estimation of an elastic constant possible. This preliminary study investigates the sensitivity of dispersion curves caused by a change in elastic constants. The Scaled Boundary Finite Element Method is used to compute special dispersion curves, which show the sensitivity value of the frequency and group velocity as a colour value. This representation allows for easy identification of patterns and local effects. Two sets of dispersion curves are presented, one set for a steel plate and the other set for a plate made of a carbon fibre reinforced polymer. In general, we notice that the sensitivity often increases with the frequency and that higher-order modes seem to be more suitable for material characterisation. Moreover, specific modes respond to material changes while others are relatively unaffected, which must be taken into consideration for material characterisation.
Akustische Verfahren eignen sich hervorragend zur Bestimmung der Werkstoffeigenschaften. Die Verfügbarkeit derartiger Verfahren ist vor allem für Kunststoffe wichtig, da deren Eigenschaften stark abhängig vom jeweiligen Herstellungsprozess und vom Alterungszustand sind. Exakte und vollständige Werte sind daher in Datenbanken oder von Herstellern nur begrenzt zu finden. Insbesondere die Entwicklung von Methoden zur Charakterisierung faserverstärkter Kunststoffe (FKV) ist nach wie vor Gegenstand der Forschung. Hier müssen anisotropiebedingt mehrere Kennwerte bestimmt werden. Da FKV zumeist als dünnwandige Bauteile zum Einsatz kommen, können die Werkstoffparameter aus den Dispersionseigenschaften der Lamb-Wellen, die sich in diesen Strukturen ausbreiten, abgeleitet werden. Dazu ist eine räumliche Abtastung des sich ausbreitenden Schallfelds erforderlich.
In der vorliegenden Untersuchung wird dieser Ansatz für die relativ neue Werkstoffklasse der faserverstärkten Thermoplaste angewendet. Diese zeichnet ein ausgeprägtes Dämpfungsverhalten und eine Anisotropie der Materialparameter aus. Dazu wurde das Schallfeld im Ultraschallbereich mit einem Laser-Doppler-Vibrometers vermessen. Rechnerisch bestimmte Dispersionskurven wurden dann an die gemessenen Werte angepasst, womit die richtungsabhängigen Materialparameter bestimmt werden konnten.
Im Vortrag wird das Messverfahren vorgestellt und auf spezielle Probleme, die sich z.B. aus dem Dämpfungsverhalten des Werkstoffs ergeben, eingegangen. Ausgewählte gemessene Werte werden mit den Ergebnissen von Referenzverfahren verglichen.