Filtern
Dokumenttyp
- Zeitschriftenartikel (13) (entfernen)
Schlagworte
- Automated manufacturing (2)
- Fatigue tests (2)
- Mechanical properties (2)
- Notch stress approach (2)
- Residual stress (2)
- Tubular X-joints (2)
- Wire arc additive manufacturing (2)
- Adaptive control (1)
- Additive manufacturing (1)
- AlMg0.7SiTiB filler wire (1)
- Automatisierte Fertigung (1)
- Carbon dioxide footprint (1)
- Digitalisierung (1)
- Digitalization (1)
- Digitization (1)
- Environmental impact categories (1)
- Equivalent stress concentration factors (1)
- GMA welding (1)
- GMR sensors (1)
- Gleeble testing (1)
- Grade S960QL steel (1)
- Grain refinement (1)
- HSLA (1)
- Hardly separable problem (1)
- Hohlprofilknoten (1)
- Kerbspannungskonzept (1)
- Laser beam welding (1)
- Life cycle assessment (1)
- Local fatigue spproaches (1)
- Low carbon steel (1)
- Magnetic stray field (1)
- Material modeling (1)
- Microstructure (1)
- Model calibration (1)
- Model order reduction (1)
- Narrow gap welding (1)
- Neural networks (1)
- Neutron diffraction (1)
- Numerical welding simulation (1)
- Open science (1)
- Open source (1)
- Precipitation hardening aluminum alloys (1)
- Proper generalized decomposition (1)
- Research data management (1)
- Resistance spot welding (1)
- Schweißnahtgeometrie (1)
- Sensor (1)
- Strain-rate (1)
- Stress-strain behavior (1)
- Structural stress approach (1)
- TIG-welding (1)
- Technical crack detection (1)
- Transformable steels (1)
- Tubular joints (1)
- Umweltschutz (1)
- Viscoplasticity (1)
- Weld seam geometry (1)
- Welding (1)
- Weldx (1)
- digital image correlation (1)
- dual phase steel (1)
- resistance spot welding (1)
- Äquivalente Spannungskonzentrationsfaktoren (1)
Organisationseinheit der BAM
- 9 Komponentensicherheit (13) (entfernen)
In order to generate a material data base for computational welding mechanics, temperature and strain-rate dependent stress-strain experiments were performed by using a Gleeble®3500 testing system. The object of the investigation was HSLA transformable steel S960QL and related solid phases as bainite, martensite and austenite. For the production of these solid phases, the base material was heat treated according to an average weld temperature cycle which was extracted within the heat affected zone of a thermal numerical weld simulation of a GMA weld. The hot tensile tests were carried out via cost-saving flat specimen geometries. Two experimental series with different strain-rates were conducted, where the longitudinal strain-rate was controlled by specification of the transversal strain-rate applying Poisson’s-ratio. Subsequently, the resulting stress-strain curves were approximated in accordance with the Ramberg-Osgood-materials law. Consequently, it is shown that the temperature and strain-rate dependent stress-strain behavior of metals can be successfully characterized by means of a Gleeble®-system.
However, this requires a control of the longitudinal strain-rate by specification of the transversal strain-rate. The related experimental procedure and the method of evaluation are explained in detail. With regard to all tested solid phases, a significant strain-rate dependency can only be observed upwards from temperatures of 400 °C. Based on experimental results, Ramberg-Osgood-parameters will be presented to describe the stress-strain behavior of steel S960QL and related solid phases for temperatures between 25 °C and 1200 °C. Furthermore, the use of costsaving flat specimen-geometry appears reasonable.
This study examines the relationship between the magnetic mesostructure with the microstructure of low carbon steel tungsten inert gas welds. Optical microscopy revealed variation in the microstructure of the parent material, in the heat affected and fusion zones, correlating with distinctive changes in the local magnetic stray fields measured with high spatial resolution giant magneto resistance sensors. In the vicinity of the heat affected zone high residual stresses were found using neutron diffraction.
Notably, the gradients of von Mises stress and triaxial magnetic stray field modulus follow the same tendency transverse to the weld. In contrast, micro-X-ray fluorescence characterization indicated that local changes in element composition had no independent effect on magnetic stray fields.
Despite the advances in hardware and software techniques, standard numerical methods fail in providing real-time simulations, especially for complex processes such as additive manufacturing applications. A real-time simulation enables process control through the combination of process monitoring and automated feedback, which increases the flexibility and quality of a process. Typically, before producing a whole additive manufacturing structure, a simplified experiment in the form of a beadon-plate experiment is performed to get a first insight into the process and to set parameters suitably. In this work, a reduced order model for the transient thermal problem of the bead-on-plate weld simulation is developed, allowing an efficient model calibration and control of the process. The proposed approach applies the proper generalized decomposition (PGD) method, a popular model order reduction technique, to decrease the computational effort of each model evaluation required multiple times in parameter estimation, control, and optimization. The welding torch is modeled by a moving heat source, which leads to difficulties separating space and time, a key ingredient in PGD simulations. A novel approach for separating space and time is applied and extended to 3D problems allowing the derivation of an efficient separated representation of the temperature.
The results are verified against a standard finite element model showing excellent agreement. The reduced order model is also leveraged in a Bayesian model parameter estimation setup, speeding up calibrations and ultimately leading to an optimized real-time simulation approach for welding experiment using synthetic as well as real measurement data.