Filtern
Erscheinungsjahr
Dokumenttyp
- Beitrag zu einem Tagungsband (46)
- Zeitschriftenartikel (34)
- Vortrag (34)
- Posterpräsentation (19)
- Buchkapitel (6)
- Beitrag zu einem Sammelband (2)
- Sonstiges (1)
Sprache
- Englisch (103)
- Deutsch (38)
- Mehrsprachig (1)
Schlagworte
- Fire (12)
- LNG (7)
- Sloshing (7)
- LH2 (5)
- Vessels (5)
- Pressure vessel (4)
- Road tankers (4)
- Tanker (4)
- Turning maneuvers (4)
- BLEVE (3)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (34)
Liquefied Hydrogen (LH2) or Liquefied Natural Gas (LNG) establish themselves as important energy carriers in the transport sector. Its storage requires tanks with Thermal Super Insulations (TSI) to keep the transported fluid cold. TSI has proven itself in various applications over a long time, but not in the land transport sector, where accidents involving collisions, fires, and their combination are to be expected. The focus of this study is to investigate the behavior of different types of TSI when exposed to a heat source that represents a fire. Therefore, a High-Temperature Thermal Vacuum Chamber (HTTVC) was used that allows the thermal loading of thermal insulation material in a vacuum and measuring the heat flow through the TSI in parallel. Within this study, 5 samples were tested regarding 3 different types of MLI, rock wool, and perlites. The thermal exposure caused different effects on the samples. In practice, this can be connected to the rapid release of flammable gases as well as a Boiling Liquid Expanding Vapour Explosion (BLEVE). These results are relevant for the evaluation of accident scenarios, the improvement of TSI, and the development of emergency measures.
Turning maneuvers originate higher forces exerted on the rail and the loss of locomotive energy, at a rate that is function of several parameters that influence the magnitude of the developed horizontal wheel-rail forces, including the friction at the centre plate and the bogie´s yaw stiffness. However, such a friction at the contact surfaces of the centre plate is needed to mitigate the Hunting phenomenon when the train moves on straight track segments. In this paper, a self-centering centre plate is proposed, consisting of a lubricated centre plate, equipped with a spring- and damper-based self-centering mechanism. Simulation results of the proposed mechanism suggest that the energy performance in turns of a train car equipped with such self-centering centre plate is comparatively better, as the peak friction forces linked to the dry friction at the contact surfaces of current centre plate designs, are avoided. The assessment of the hunting performance of the proposed device in straight track segments is proposed as the continuation of this work.
A facility is proposed in this paper to apply a selective carburizing process to the lateral faces of a railways´ head, aiming to increase its carbon content and to decrease the friction coefficient in case that the flange of the railway car wheel gets in contact with the rail during turning. Such a treatment would reduce the energy that is lost during the turning maneuvers performed by the vehicle, further improving the energy efficiency of the railway car. The facility consists of a furnace, which should be set next to the rails´ hot-rolling facility, in order to use the available enthalpy. The proposed furnace is equipped with what is necessary to avoid the decarbonization of the remaining rail material, based upon batteries of oxy-acetylene burners that are installed at the bottom of the furnace, on the opposite side to the carburizing surface. An experimental facility is necessary to validate the operational principles for the equipment proposed in this paper. On the other hand, a study should also be carried out to assess the effect of any rail welding process on the carburized surfaces.
The interaction of the vehicles with the pavements imply damaging effects on both systems, as a function of the operating conditions and design characteristics of both systems. These effects influence the road pricing as well as the maintenance costs of the vehicles. In this paper, a simulation scheme has been proposed to analyze such interaction in massive way, involving a multivehicle models was the uncoupling of the roll and pitch responses. Results suggest that the damaging effects on the pavement and the vehicle, depends on the position along the road profile. However, the vertical design of the road would mainly affect the pavement damage, while the turning maneuvers would strongly influence the damage of the vehicle. Many uses can be identified for the proposed simulation scheme, involving different design and operating conditions for both systems.
In spite that transport activities do not represent the biggest contributor of pollutants emissions, their reduction has been a priority as some other externalities are associated to such emissions and to the transport itself. A crucial element to characterize the behavior of the vehicles against the environment are the losses that such vehicles exhibit in a passive way, that is, without any involvement of power conditions. The energy loses due to the rolling, the drag and to the friction in mechanical components, have been assessed so far in terms of the stopping acceleration when the vehicle idles on a ramp. However, such a testing procedure produces some uncertainties due to the dynamic conditions that are considered. To avoid such critical limitations, in this paper a testing procedure and facility are proposed, which are based on static conditions of the vehicle at the initiation and at the ending of the test, which are assumed to provide a better reliability to the testing. Some preliminary theoretical analysis should be made in order to validate the operational principles proposed herein for such testing facility.
Steam generator (SG) tubes are part of the primary circuit of pressurised water reactors and therefore also part of the pressure retaining boundary components. Furthermore, steam generator tubes are the components which guarantee the separation between the primary and secondary circuits. Therefore the knowledge of the loss of tube integrity as soon as possible is an essential. Optimised nondestructive testing methods based on the eddy current array technique are used to find material degradation, especially intergranular stress corrosion cracks during the periodical in-service inspection. These methods are supported by the measurement of the leakage rate during operation based on radioactivity and Tritium measurement regarding a high crack grows. Shutdown criteria depending on leakage rates which are described in the operation procedures but there are no specifications about the conditions for the measured leakage. Is the leakage coming from a single crack or are there multiple cracks or is this the leakage of a critical crack. With the help of FE calculations answer about the uncertainties of leakage rate versus critical crack grows were found. Shutdown criteria must guarantee to avoid critical crack sizes, i.e. between the measured tritium activity and the critical crack size must be a safety gap.
A new tank design for Hazmat
(2016)
Initial studies have shown pre-deformed honeycomb structure
pressure vessels to have comparable burst pressure to straight steel vessels.
It was shown that honeycomp structured tanks have a higher energy absorption than straight steel tanks.
Future studies will investigate optimization of the deformed plate, to determine if increased payloads or a reduced wall thickness can be achieved.
A filling process of the pressure bottle used for the air storage was investigated by numerical simulations. During the filling process, the temperature was rising up to maximal value and after that started to decline. The good match was found between experimental and numerical results. In order to reproduce the experimental conditions, the process of the filling bottle was controlled by the pressure which varied in time. This filling strategy influenced furthermore the mass flow rate and the air flow velocity. Because of the geometrical symmetry, the simulation was calculated as an axisymmetric problem.
Avoiding road crashes has been the purpose behind many specialized software and hardware systems, involving both active and passive safety principles. Global Positioning technologies were incorporated into the transportation systems with the main purpose of acquiring the position of the vehicle under a continuous basis, for security and economy purposes. However, the GPS data can also be used for assessing the level of safety at which the vehicle is driven. On the basis of the essential data available from commercial GPS devices, in this paper we propose a combined performance measurement to assess the road safety level at which the vehicle is being driven. Such performance measure uses GPS data of the vehicle displacement, including the speed and the acceleration, as well as the course (latitude and longitude coordinates), in an integral driving assessment formulation that can run in real time. Results from the experimental use of this formulation suggest that the level of safety in the driving is time dependent, and that there are risky situations when different factors converge.
GPS-data based calculation scheme for assessing, in real-time, the level of safety exerted during driving, has been described and used. The several variables involved considered the main factors that lead to road mishaps, including the speed, the acceleration and the effects that these variables have on the vehicle when it is negotiating a turn. The performance measure combines three individual performance outputs: speed, acceleration and a hybrid performance measure considering the speed, the acceleration and the change in latitude/longitude. The measures are designed in such a way that weighting factors can be calibrated in order to establish certain critical parameters. On the other hand, the terms in the equations preclude any division by zero of the involved ratios. On the other hand, the simplicity of the equations makes it possible to carry out the assessment in real time. The use of the resultant performance measure to a relatively long path, together with its current average value, indicates that the safe performance of the driving changes with time, and that, for the selected values of the calibration constants, the traveling speed dominates the overall safety performance of the driving. Furthermore, the different calibration constants provide the possibility of considering different types of hazmat carrying vehicles. While many other formulation components could be integrated into the performance measure, this three-component performance measure could be used to assess the driving of a hazmat-carrying vehicle, in order to detect and to prevent dangerous conditions, such as driver fatigue.
Finally, the implementation of the different performance measure formulations in a system such as the one described in the introduction of this paper, could be straightforward.
A simplified methodology is proposed to estimate the dynamic pressures developed within partially filled cylindrical vertical tanks when subjected to earthquake-related horizontal accelerations. The total pressure at the bottom of the tank is calculated as the superposition of vertical and horizontal pressures. While the magnitude of the vertical pressure depends on the free surface height of the liquid, the horizontal pressure depends on the magnitude of the horizontal acceleration and on the diameter of the tank. The liquid free surface oscillation angle is simulated based upon the principles of the simple pendulum analogy for sloshing. The length of the pendulum, however, is set on the basis of a methodology to calculate the free sloshing frequency of partially filled containers. Such a methodology is experimentally verified in this work. The outputs of the model for full scale situations, suggest that the lateral perturbation - sloshing phenomenon (earthquake effect) can generate an increase in the total pressure of 56% above the no lateral perturbation situation, further suggesting that such an overpressure should be taken into account when designing tanks that could be potentially subjected to earthquake-related perturbations.
Wheel forces generate stresses in the rail as a function of several vehicle and infrastructure characteristics and operating conditions. The different components of the wheel forces develop strains in the rail which contain an elastic and hysteretic (irreversible) components. The irreversible deformations of the rail would be associated with locomotive energy losses. In this paper, a testing facility is proposed to indirectly characterize the level of stresses in the rail, in terms of the energy that is lost during tuming maneuvers. Different potentially influential factors are considered, including the friction at the Center plate, the wheelbase length, the distance between bogies and the radius of the curved track. The change
in the potential energy during a U-turn displacement is measured. In this respect, an experimental model under this operating principle, aimed at validating such a principle of Operation, reveals a significant effect of the friction at the center plate on the energy lost during turning maneuvers, and consequently, on the level of stresses in the rail.
A testing rig for the measurement of the dynamic loads on the rails due to cargo sloshing,has been proposedin this paper. The system represents a scale-down approach that simulates astraightening maneuver of the railway car after negotiating a turn. As part of the experimental effort, a mathematical model was developed that, oncevalidated, will provide more insights about the potential effect of many other cardesign factors, on the level of stress developed in the raildue to the sloshing cargo.A fundamental output from the testing, will be the objective comparison between the railloads due toa sloshing and a non-sloshing cargo, together with a validated model that wouldallow parametric studies in relation withthe potential effect,of several track and carproperties,on the magnitude of the sloshing forces on the rail.
Rear-end crashes involving heavy trucks as the leading vehicle, and cars as the impact vehicle, cause many deaths and permanent injuries to car´s occupants. Measures have been thus taken in the trucks to prevent underride crashes, including the mounting of stiffer underride guards, set at car´s bumper height. In this respect, an active acceleration system(AAS), installed in the truck, could also contribute to mitigate the effects of These crashes, through the decrease of the relative Speed of the vehicles at the instant of the crash. In this paper, an AAS system is proposed, under the principles of ultrasonic sensors and an actuator for the truck´s accelerator mechanism. Simulation results of the operation of this AAS system, suggest that such a system could decrease the relative impact speed around 8% for an initial relative speed of 10 m/s.
Externalities of the road transportation are multidimensional in nature and involve the road-vehicle interaction under different environmental conditions. Estimating the pavement and vehicle damage potentials as a function of the condition sunder which such interaction takes place, is important to avoid accelerated or catastrophic damages in these systems. Such an assessing is crucial from the perspective of pricing the effects of the vehicle on the infrastructure and vice versa. The existing models for pricing such interaction, critically depends on gross average statistical models. In this paper, it is proposed a deterministic approach to realize such an assessment, based upon validated approaches for the pavement damage. The simulation scheme considers different degrees-of-freedom vehicle models, and a discrete asphalt pavement, that make possible the simulation of massive traffic situations on realistic road lengths.
An overview of test standards and regulations relevant to the fire testing of pressure vessels
(2021)
Fire exposure of storage and transportation vessels of hazardous materials (including pressure liquefied gases) can result in BLEVEs and other high-consequence incidents with large societal and economic impacts. To reduce risk most countries have numerous regulations, codes of practice and guidance notes covering the design, operation and maintenance of vessels and thermal protection systems. Yet despite such regulations there remains no internationally accepted fire test procedure for pressure vessel and accompanying thermal protection systems that is capable of meeting a range of regulatory requirements. This paper considers some of the regulations in place in the western world and considers the origin of these based on large and medium-scale testing conducted to date. It examines conditions found in these tests to propose a set of recommendations on which to base a standard method of test. These recommendations are proposed as being representative of a credible large pool fire scenario that may occur.
The interest in hydrogen-based green energy is increasing worldwide, and the same is true for hydrogen-powered vehicles. Among the possible solutions to store hydrogen in such vehicles, cryogenic tanks equipped with multi-layer insulation (MLI) are the most promising to increase the amount of energy stored per unit volume. However, MLI is affected by severe deterioration when exposed to an external source of heat such as a fire following a car accident, leaving the tank unprotected and leading to failure in a relatively short time. In this work, a one-dimensional model to evaluate MLI thermal degradation when a liquid hydrogen tank is exposed to fire is presented. The relevance of taking MLI degradation into account when simulating the pressure increase due to external fire exposure is here demonstrated through the analysis of several case studies. The results show that MLI systems performance depletes within a few minutes of exposure to hydrocarbon poolfire.
A dynamic simulation model for a tanker ship along the Rhine River has been proposed, based on a simplified computational scheme, involving a two-degree-of-freedom roll plane multibody system, subjected to lateral accelerations estimated on the basis of measured data. The resulting equations of motion are solved through the transition matrix approach. The results suggest that many contributing factors were involved in the capsizing of the ship, including the relatively high speed of the river water and the meandering path of the infrastructure, further affected by dynamic effects derived from the behavior of the payload and from the steering maneuvers performed.
Greenhouse gas emissions caused by human activities remain one of the most important subjects of international discussions. The routine gas flaring has been estimated to be responsible for as much as 1% of global carbon dioxide emission per year. Gas flaring analysis is one of the key-interest subjects in remote sensing community. Some of the existing publications use remote sensing techniques with satellite imagery to derive information about flame temperature and further about to estimate the volume of the flared gas. The often missing element is an in-situ measurement analysis of gas flames, combining signals recorded by a camera on-ground and data on flared gas volume, temperature and gas type. In order to address this problem, an experiment was conducted, in which the gas flame was recorded by thermal cameras on-ground, simultaneously to an aerial survey and the gas flow was measured at the same time on-ground. The measurement setup was designed in cooperation between Institute of Optical Sensor Systems of German Aerospace Center (DLR) and German Federal Institute for Materials Research and Testing (BAM). Cameras recording in thermal and mid-wave IR wavelengths were used to record the burning gas on-ground and from the aerial survey. All the measurements have been compared and statistically analysed with respect to the recorded temperature. The purpose of the examination was to describe the signal changes in thermal imagery with respect to changes in energy, emitted by the burning process. This approach will allow for later calculation of the amount of energy in form of thermal radiation sent from the flame to the satellite.
How can the risk of a BLEVE be reduced? That is the main question based on different research projects. In various large scale fire tests fire protection coating systems were used of different manufacturers. The degree of the coating as well as the layer thickness and the processing were varied. These experimental configurations were partly tested with and without pressure relief valve. The pressure relief valves were not protected again the thermal Load from the test fire. The ambition is to find a minimum of the thickness from the fire protection coating witch delay a BLEVE up to 90 minutes. Here are given the most interested configurations of tanks in fire and a description of the test-rigs.
Exposure of pressure vessels to fire can result in catastrophic explosion and escalation of accidents. The safe transportation of cargo in pressure vessels therefore requires knowledge of what will happen to the cargo in the event of a vehicle derailment or rollover resulting in fire exposure. The chapter presents an overview of selected testing and modelling work undertaken to understand the thermohydraulic processes within a vessel that drive pressurization during fire. A series of experiments highlighting the importance of adequate design and selection of protection systems are summarized. It is concluded that pressure relief alone is typically insufficient to prevent vessel rupture, but the combination of relief and thermal coatings can be effective.
Transport safety depends in great extent of what happens to the cargo once the carrying vehicle derails or rollovers. The exposure of tanks to direct fire is a condition that potentially involves catastrophic consequences. Studying the behavior of the contained fluid under these drastic circumstances, is critical to develop methods and techniques to mitigate the serious consequences of many mishaps. In this paper, the experimental potentials of a Particle Image Velocimetry data acquisition system are described, for providing experimental data that could be used to calibrate mathematical models. As an example of the situations that need to be modelled, an experiment is described concerning the effect of the boundary conditions and protecting devices, on the rate of variation of pressure and temperature of the fluid in a tank exposed to a direct fire. In this regard, the results emphasize the importance of equipping the vessels with both thermal insulation and safety valves.
Small and large-scale tests have been carried out Pressure vessel – to improve numerical modelling Different types of fire must be distinguished Modelling of vessels were discussed Test configuration has been developed to see what happens in the vessel First results encourage us to continue the Research Thermohydraulics needs further work (boundary layers).
In einem von der BAM Bundesanstalt für Materialforschung und -prüfung durchgeführten Forschungsvorhaben wurde untersucht, inwieweit bei Gefahrguttanks im Brandfall ein 'BLEVE', d. h. ein Versagen der Umschließung mit anschließender Freisetzung der Flüssigkeit bzw. des verflüssigten Gases, verzögert bzw. verhindert werden kann.
There was a need to validate the longitudinal performance required for the cargo securement, as current standards exhibit differences.
A model has been proposed in this paper, to simulate the effect of a shifting cargo on the braking efficiency of the vehicle. Results suggest that the braking efficiency can be greater in the case of a shifting cargo, as a result of the uncoupling of the cargo-vehicle systems, implying that similar braking forces are exerted on a reduced mass. The shifting of the cargo can occur as a result of the vibration of the vehicle, that leads to having a diminished friction force to prevent the shifting of the cargo.
There was a need to validate the longitudinal performance required for the cargo securement, as current standards exhibit differences. A model has been proposed in this paper, to simulate the effect of a shifting cargo on the braking efficiency of the vehicle. Results suggest that the braking efficiency can be greater in the case of a shifting cargo, as a result of the uncoupling of the cargo-vehicle systems, implying that similar braking forces are exerted on a reduced mass. The shifting of the cargo can occur as a result of the vibration of the vehicle, that leads to having a diminished friction force to prevent the shifting of the cargo.
Commidities and rail damage
(2018)
A roll-plane simplified model, representing the suspended body-cargo of a railway car, was developed to simulate thedynamic response of a railway car while subjectedto lateral acceleration derived from its traveling along curved tracks. The model provides the means to calculate the suspension forces, which are supposed to be transmitted to the bogie´s wheelset. For the analysis of the potential effect of such forces on the railway fatigue life, different performance measures were considered, under different concepts. A family of curves were produced to analyze the effect of the height of the center of gravity of the body-cargo system, on the different performance measures. The resultingdiagramswereused to assess the rail damage potentials offour different railway cars. Results suggest that the height of the center of gravity, associated to the different types of railway cars, nonlinearly and strongly affects the fatigue lifeof the rail, with the double stack car being the moreinfrastructure-aggressive. In this respect, experimental evidence should be provided about such remarkable effects, so as to supportsome operational recommendationsthat shouldbe taken to mitigate these effects, including, for example, the regulation of the traveling speed of some vehicles.
Commodities and rail damage
(2018)
The normalized contact-mechanics fourth-power law approach for the
dynamic loads, suggest: worst railway use situation (double deck at 65 km/h) is 350 times that of the less rail damage situation (flat car at 45 km/h).
The normalized dispersion approach for the dynamic loads (Dynamic Load Coefficient), suggest that the worst railway use situation (double deck at 65 km/h) is about 4 times that of the less rail damage Situation (flat car at 45 km/h).
The potential effect of the different types of cars on the railway fatigue life could be significant, as a function of the vehicle speed.
The experimental validation of these outputs will be carried out as a continuation of this research effort. In addition to that, it should be mentioned that the associated simplified model could be used to analyze some other situations, related with the transport safety of different products.
The prediction of the plastic collapse load of cylindrical pressure vessels is very often made by using expensive Finite Element Computations. The calculation of the collapse load requires an elastic-plastic material model and the consideration of non-linear geometry effects. The plastic collapse load causes overalls structural instability and cannot be determined directly from a finite element analysis. The ASME (2007) code recommends that the collapse load should be the load for which the numerical solution does not converge. This load can be only determined approximately if a expensive nonlinear analysis consisting of a very large number of sub steps is done. The last load sub step leading to a convergent solution will be taken as the critical load for the structure. In the instability regime no standard finite element solution can be found because of the lack of convergence of the numerical procedure. Other methods for the calculation of the allowable pressure proposed by the ASME code are the elastic stress analysis and the limit load analysis. In the present paper the plastic collapse load for a cylindrical pressure vessel is determined by an analytical method based on a linear elastic perfectly plastic material model. When plasticity occurs the material is considered as incompressible and the tensor of plastic strains is parallel to the stress deviator tensor. In that case the finite stress-strain relationships of Henkel can be used for calculating the pressure for which plastic flow occurs at the inside of the vessel wall or in the case of full plasticity in the wall. The analytical results are fully confirmed by finite element predictions both for axisymmetric and high costs three dimensional models. The analytical model can be used for fast predictions of the allowable load for the design of a large variety of pressure vessels under safety considerations. The accuracy of the predicted collapse load largely depends on the quality of the temperature dependent wall material data used both in the analytical and numerical calculations.
More than 400 Mt of dangerous materials are transported in Germany every year, of which 150 Mt are by road. Tank containers, tank vehicles and rail tank cars are used for the carriage of dangerous goods in large quantities. Data on the operating life of tanks are only available, in practice, to a minor degree. They are only partly published, mainly after accidents.
The BAM-List - Requirements for Tanks for the Carriage of Dangerous Goods, which has compatibility evaluations of metallic and polymeric materials, has been the basis for substance-related prototype approvals for tank containers and portable tanks designed for the carriage of dangerous goods by the BAM since publication of the first edition in 1989. These data are also used for the approval of rail tank cars and road tank cars and are used as a source of knowledge not only in Germany but also worldwide.
Tank leakages caused by tanks or rail tank cars being made of tank and sealing materials which are not resistant to the fill goods are avoided by using the material resistance data of the BAM.
Corrosion damage is among the main causes of damage. Uniform and non-uniform area corrosion without mechanical stress in aqueous substances is one of the most frequent types of corrosion during the transport of chemicals in tanks. Much damage by pitting corrosion occurs during the transport of substances containing chlorides or substances which separate chloride ions in the presence of moisture.
Operational stresses are caused by the effects of both the road and the dangerous goods being transported. Mechanical damage often results from long-term overstressing and occurs after longer operating times.
Operational failures cause damage which may appear during the service of tank containers, road tank cars or rail tank cars. The damage results from the inattention of employees when opening and closing the valves. Traffic accidents also cause damage to tanks and frames.
Many cases of damage are due to weld area cracks resulting from four basic errors in construction, material, manufacturing and operation. Manufacturing errors can be undetected and the starting point of cracks which only grow under service conditions.
Manufacturing errors result from variations in measurement and design, fittings, state of surface (hardness, abrasiveness) and mechanical surface damage (scratches, cracks). Incorrectly welded joints and errors during mechanical deformation are typical mistakes when installing the component parts. Variations in the wall thickness or combinations of different materials lead to manufacturing errors too. A lot of tanks are not used for the transport of dangerous goods before the end of their service life as they do not fulfil the revised technical safety requirements in the Dangerous Goods Regulations.
Predictions in the BAM-List based on literature data and corrosion test results are reflected in the service (operating) life. Rail tank cars made of carbon steel, for example, which are mainly used for the transport of petroleum products, can achieve a service life of 40 – 50 y.
Rail tank cars produced of austenitic CrNi- or CrNiMo-steel can reach an operating life of at least 30 y, whereby the corrosiveness of the transport substances plays an important role.
The efficiency and safety of railway transportation depend both on numerous factors linked to the vehicle, the infrastructure, the operator and the environment. Curved tracks are subjected to demanding situations due to elevated stress levels, as a function of the operating conditions and vehicle/infrastructure design. In such segments, steering forces are superimposed to lateral load transfers. The steering forces depend on the condition and the design of the centre plate and bogies’ suspensions design. While the friction at the centre plate provides the needed damping to mitigate the hunting vibration of the bogie in straight track segments, such yaw resistance originates high steering forces and rail damage on curved tracks. A centre plate with low friction at turns and high friction at straight track segments would thus be highly advantageous. In this paper, a centre plate design is proposed which provides a yaw-rotation resistance torque that depends on the bogie-car relative position. Two different designs are considered for that purpose, one that combines a spring-acted centring mechanism with a lower pair kinematics, while the other one involves higher kinematic pairs which should incorporate lateral damping elements. As a result of using an engineering design approach, the higher kinematic pairs-based design is recommended however, the validation of such operational principles, including the introduction of the needed damping, should be configured on the basis of experimental models.
Die Vorhersage der Beanspruchung bei plastischem Versagen von zylindrischen Druckbehältern wird häufig mittels Finite Elemente Berechnungen durchgeführt. Die Berechnung der zulässigen Beanspruchung erfordert ein elastisch-plastisches Werkstoffmodell und die Berücksichtigung von nichtlinearen geometrischen Effekten. Das plastische Versagen verursacht eine gesamte Strukturinstabilität und kann nicht direkt aus der Finite Elemente Analyse bestimmt werden. In dem vorliegenden Beitrag wird die Beanspruchung für plastisches Versagen eines zylindrischen Druckbehälters mittels eines analytischen Verfahrens basierend auf einem linear elastischen ideal-plastischen Materialmodell bestimmt. Wenn Plastizität auftritt, wird zum einen der Werkstoff als inkompressibel und zum anderen der Tensor der plastischen Dehnungen als parallel zum Spannungsabweichungstensor angenommen. In diesem Fall kann die Spannungs-Dehnungs-Beziehung von Henkel angewendet werden, um den Druck zu berechnen, bei dem plastisches Fließen und Versagen eintritt. Die analytischen Ergebnisse werden von den Finite Elemente Berechnungen vollkommen bestätigt.
Im Gefahrgutrecht, insbesondere im Bereich der Gefahrguttanks für den Landverkehr, hat der Bezug zur technischen Norm aufgrund der Rechtsfortentwicklung eine fundamentale Bedeutung erlangt. Damit die Interessen der deutschen Tankhersteller genügend Berücksichtigung finden können, ist die kontinuierliche Mitarbeit der betroffenen Wirtschaftskreise in den nationalen und internationalen Normungsgremien erforderlich. Dieser Zusammenhang, der für den einzelnen Hersteller mit erhöhtem Aufwand verbunden ist, wird von den betroffenen Kreisen nicht flächendeckend wahrgenommen. Der Beitrag analysiert Gründe hierfür und macht Vorschläge zu leichten Korrekturen in der inhaltlichen Ausrichtung der Normung.
Degradation of material properties significant for lifetime extension of nuclear power plants
(2010)
The discussion about the right energy sources or alternative energy generation goes around the world, mostly in connection with green-house gas reduction. Therefore, some countries have started to consider extending operation of nuclear power plants. This demands an extensive plant life management as well as the knowledge of the degradation in material properties. The Basis Safety Concept (BSC) in Germany observed this circumstance. Still, lifetime extension is not an issue in Germany due to phase out of nuclear energy. Part of the BSC is the application of non-destructive examination (NDE) methods from the beginning, i.e. from component manufacture, to the end of life. The application of a NDE method to detect and size defects in components in nuclear power plants is presented. Some material properties and their degradation during increase of operation time are also in the focus of this paper.
Die BAM – Bundesanstalt für Materialforschung und -prüfung führt schon seit vielen Jahren auf zwei Brand- prüfständen Brandprüfungen z.B. an Transport- und Lagerbehältern für radioaktive Stoffe oder zur Prüfung von Brandschutzbeschichtungen durch. Als Brandmedium wird auf diesen Prüfständen Flüssiggas (Propan- Butan-Gemisch C) eingesetzt, mit dem die Prüfobjekte simulierten Unfallfeuern ausgesetzt werden. Mit dem neuen Jetfire – Prüfstand der BAM können seit Anfang 2018 diverse Belastungsszenarien nach den Anforde- rungen der ISO22899-1:2007 [1] simuliert werden.
Liquid cargo has a significant impact on the interface wheel-track interaction. The sloshing affects the track-railcar's dynamic behavior. The effect is detectable at the track level and at the vehicle. Its characterization requires the combination of different techniques:
Empirical Mode Decomposition (EMD)
Time-Frequency Maps
Sloshing occurred when significant perturbations happened in the railcar:
The railcar entered a curve
Reduction in its travel speed
A railcar with a tank is a clear example of a multibody dynamic system with a nonlinear behavior.
This paper presents the study of the impact caused by a liquid Cargo on a railway infrastructure. The dynamic behavior of a tank car corresponds to a multibody dynamic system with several degrees of freedom. This study’s data were obtained from a scale experimental fixture consisting of a track and a railcar with a tank. The track was instrumented with strain gauges and the railcar with accelerometers. The data showed non-periodic and periodic terms; therefore, the results were analyzed with the Empirical Mode Decomposition method (EMD).
It was found that the EMD identified the signal components that were related to the sloshing. These components represent the mode shapes of the original signal.
The location of the sloshing in the track was found applying spectrograms to the accelerometer data. This paper’s experimental outputs suggest that the sloshing effect is detectable at the track and in the vehicle dynamics.
The US Department of Transportation, Federal Railroad Administration (FRA) current regulations for rail tank cars in the United States stipulate that, for certain hazardous materials, tank cars shall have a thermal protection system capable of preventing rupture of the tank for 100 minutes when exposed to an engulfing fire with a blackbody equivalent flame temperature of 871 °C (+/- 56°C), and that tanks shall have a pressure relief device set at an appropriate level (depending on the type of tank car and contents). Pressure relief devices are a source of non-accident releases, and hence may cause serious incidents when tanks are transporting hazardous materials. Industry in North America would therefore benefit from removal of pressure relief devices on tanks transporting certain hazardous materials. Such an approach is known as full Containment, and is standard practice in Europe. In 2014 the FRA commissioned an experimental study to investigate the ability of a specific design of rail tank to resist rupture without incorporating a pressure release valve. As a precursor to tests on tanks there was a need to develop and characterise a simulated pool fire capable of reliably exposing large-scale tanks to repeatable, uniform conditions. This paper describes such a fire test setup, developed using a burner array system fuelled by liquid propane and designed to produce luminous, low velocity flames representative of those found in large hydrocarbon pool fires. The experimental set-up is described, along with the Instrumentation (directional flame thermometers, infra-red camera, and thermally massive calorimeter) and methodology used to characterise the fire. Comparisons are made against previous fire tests on vessels to assess the suitability of the experimental set-up for future vessel testing.