Filtern
Erscheinungsjahr
Dokumenttyp
Sprache
- Englisch (28)
Referierte Publikation
- ja (28) (entfernen)
Schlagworte
- Experimental modelling (2)
- Liquid cargo (2)
- Pressure vessel (2)
- Sloshing (2)
- Tanker (2)
- Aerial survey (1)
- Ageing effects (1)
- Analytical solution (1)
- Avoid (1)
- Axial cracks (1)
Organisationseinheit der BAM
More than 400 Mt of dangerous materials are transported in Germany every year, of which 150 Mt are by road. Tank containers, tank vehicles and rail tank cars are used for the carriage of dangerous goods in large quantities. Data on the operating life of tanks are only available, in practice, to a minor degree. They are only partly published, mainly after accidents.
The BAM-List - Requirements for Tanks for the Carriage of Dangerous Goods, which has compatibility evaluations of metallic and polymeric materials, has been the basis for substance-related prototype approvals for tank containers and portable tanks designed for the carriage of dangerous goods by the BAM since publication of the first edition in 1989. These data are also used for the approval of rail tank cars and road tank cars and are used as a source of knowledge not only in Germany but also worldwide.
Tank leakages caused by tanks or rail tank cars being made of tank and sealing materials which are not resistant to the fill goods are avoided by using the material resistance data of the BAM.
Corrosion damage is among the main causes of damage. Uniform and non-uniform area corrosion without mechanical stress in aqueous substances is one of the most frequent types of corrosion during the transport of chemicals in tanks. Much damage by pitting corrosion occurs during the transport of substances containing chlorides or substances which separate chloride ions in the presence of moisture.
Operational stresses are caused by the effects of both the road and the dangerous goods being transported. Mechanical damage often results from long-term overstressing and occurs after longer operating times.
Operational failures cause damage which may appear during the service of tank containers, road tank cars or rail tank cars. The damage results from the inattention of employees when opening and closing the valves. Traffic accidents also cause damage to tanks and frames.
Many cases of damage are due to weld area cracks resulting from four basic errors in construction, material, manufacturing and operation. Manufacturing errors can be undetected and the starting point of cracks which only grow under service conditions.
Manufacturing errors result from variations in measurement and design, fittings, state of surface (hardness, abrasiveness) and mechanical surface damage (scratches, cracks). Incorrectly welded joints and errors during mechanical deformation are typical mistakes when installing the component parts. Variations in the wall thickness or combinations of different materials lead to manufacturing errors too. A lot of tanks are not used for the transport of dangerous goods before the end of their service life as they do not fulfil the revised technical safety requirements in the Dangerous Goods Regulations.
Predictions in the BAM-List based on literature data and corrosion test results are reflected in the service (operating) life. Rail tank cars made of carbon steel, for example, which are mainly used for the transport of petroleum products, can achieve a service life of 40 – 50 y.
Rail tank cars produced of austenitic CrNi- or CrNiMo-steel can reach an operating life of at least 30 y, whereby the corrosiveness of the transport substances plays an important role.
Steam generator (SG) tubes are part of the primary circuit of pressurised water reactors and therefore also part of the pressure retaining boundary components. Furthermore, steam generator tubes are the components which guarantee the separation between the primary and secondary circuits. Therefore the knowledge of the loss of tube integrity as soon as possible is an essential. Optimised nondestructive testing methods based on the eddy current array technique are used to find material degradation, especially intergranular stress corrosion cracks during the periodical in-service inspection. These methods are supported by the measurement of the leakage rate during operation based on radioactivity and Tritium measurement regarding a high crack grows. Shutdown criteria depending on leakage rates which are described in the operation procedures but there are no specifications about the conditions for the measured leakage. Is the leakage coming from a single crack or are there multiple cracks or is this the leakage of a critical crack. With the help of FE calculations answer about the uncertainties of leakage rate versus critical crack grows were found. Shutdown criteria must guarantee to avoid critical crack sizes, i.e. between the measured tritium activity and the critical crack size must be a safety gap.
Degradation of material properties significant for lifetime extension of nuclear power plants
(2010)
The discussion about the right energy sources or alternative energy generation goes around the world, mostly in connection with green-house gas reduction. Therefore, some countries have started to consider extending operation of nuclear power plants. This demands an extensive plant life management as well as the knowledge of the degradation in material properties. The Basis Safety Concept (BSC) in Germany observed this circumstance. Still, lifetime extension is not an issue in Germany due to phase out of nuclear energy. Part of the BSC is the application of non-destructive examination (NDE) methods from the beginning, i.e. from component manufacture, to the end of life. The application of a NDE method to detect and size defects in components in nuclear power plants is presented. Some material properties and their degradation during increase of operation time are also in the focus of this paper.
In Europe, tanks designed on different safety philosophies are used for transporting one and the same liquid dangerous goods (Krautwurst, 2011). Owing to this circumstance, the BAM was commissioned by the BMVBS to conduct a research project designed to analyse and assess the equipment of tanks. Furthermore in these project were researched some failure mechanism of pressure relief devices (PRD).
Based on the knowledge gained, possible solutions were worked out under safety-relevant aspects that would benefit tank transport by providing a lower hazard potential. Besides looking at the mode of operation and the construction of PRV, their blow-off characteristics and total flow rate are considered from a safety engineering point of view.
Based on in-depth studies, a concept for and the further approach to examinations of the failure limits of PRD, especially of spring loaded relief valves, was developed and comprehensively described in the report “The use of safety devices, particularly safety valves, on transport containers” (Pötzsch, Reich, & Jochems, 2011).
The purpose of this study was to investigate failure causes of safety valves by normal modes and accidental fire heat loads. A series of investigations for different influences using safety valves for tanks were obtained. Testing vibration modes and corrosion presents some design limits. Experimental study of a pressure vessel engulfing in fire identify significant design limits. The complete set of results provides direct information of fail-safe modes and discusses the usage.
Hunting is a potentially dangerous phenomenon related to the lateral oscillation of the wheels that impacts the rails and causes the wear of the infrastructure’s components. Therefore, the analysis and timely detection of hunting can lead to the application of corrective maintenance tasks, reducing damages, and costs and even derailments as a result. In this work, the vibration response of a finite element model of a rail with hunting-induced loads by a single wheel is analyzed in three directions: longitudinal, lateral, and vertical. The contact patch forces are calculated by means of Simpack® using the Kalker linear theory and the contact Hertz theory. The system is solved by using the Newmark-_ approach. The results of the deflection and vibration analysis, following the proposed methodology, show how the different characteristics of the loads impact the rail.
The objective of this paper is to describe and to validate a simplified pendulum-analogy model to simulate the interaction of a liquid cargo with ist carrying vehicle. The resulting testing rig consists of a rectangular container, spring supported on a two wheelset-bogie having a scale down of 1/10 with respect to a full-size equipment. The testing rig is used to validate a simple pendulum-based, simplified three degree-of-freedom mathematical model of the response of a partially filled container to lateral accelerations. The length of the pendulum is set according to validated methodologies. The resulting mathematical scheme reveals a high correlation with the experimental output, on the order of 99%, while some other performance measures, related to the peak forces and the range of variation of the wheel-rail forces, also show good concordance with the experimental results.
A methodology is proposed for the experimental analysis of the liquid cargo effect under combined orthogonal accelerations. To simultaneously subject the vehicle-cargo system to longitudinal and lateral accelerations, the vehicle is set obliquely on a tilt table. The experimental outputs suggest that there is a significant effect of the liquid cargo on the lateral load transfer ratio (LTR), on the order of 20%, which is attributable to the resulting shifting of the liquid cargo’s centre of gravity. That is, the peak LTR values due exclusively to sloshing were not significant, in such a way that the liquid cargo would only pose a safety risk under a steady acceleration input.
Also, the inverse of the product of the magnitude of the acceleration times the free surface length, correlates with the liquid cargo effect. That is, the magnitude of the input acceleration is not fully determinant for greater load transfers.
This paper presents a method for processing acceleration data registered on a train and determining the health condition of a subway’s substructure. The acceleration data was converted into a dynamic deformation by applying a transfer function defined using the Empirical Mode Decomposition Method.
The transfer function was constructed using data produced on an experimental rig, and it was scaled to an existing subway system. The equivalent deformation improved the analysis of the dynamic loads that affect the substructure of the subway tracks because it is considered the primary load that acts on the track and substructure. The acceleration data and the estimated deformations were analyzed with the Continues Wavelet Transform. The equivalent deformation data facilitated the application of a health monitoring system and simplified the development of predictive maintenance programs for the subway or railroad operators. This method better identified cracks in the substructure than using the acceleration data.
Die Vorhersage der Beanspruchung bei plastischem Versagen von zylindrischen Druckbehältern wird häufig mittels Finite Elemente Berechnungen durchgeführt. Die Berechnung der zulässigen Beanspruchung erfordert ein elastisch-plastisches Werkstoffmodell und die Berücksichtigung von nichtlinearen geometrischen Effekten. Das plastische Versagen verursacht eine gesamte Strukturinstabilität und kann nicht direkt aus der Finite Elemente Analyse bestimmt werden. In dem vorliegenden Beitrag wird die Beanspruchung für plastisches Versagen eines zylindrischen Druckbehälters mittels eines analytischen Verfahrens basierend auf einem linear elastischen ideal-plastischen Materialmodell bestimmt. Wenn Plastizität auftritt, wird zum einen der Werkstoff als inkompressibel und zum anderen der Tensor der plastischen Dehnungen als parallel zum Spannungsabweichungstensor angenommen. In diesem Fall kann die Spannungs-Dehnungs-Beziehung von Henkel angewendet werden, um den Druck zu berechnen, bei dem plastisches Fließen und Versagen eintritt. Die analytischen Ergebnisse werden von den Finite Elemente Berechnungen vollkommen bestätigt.