Filtern
Erscheinungsjahr
Dokumenttyp
- Beitrag zu einem Tagungsband (46)
- Zeitschriftenartikel (34)
- Vortrag (34)
- Posterpräsentation (19)
- Buchkapitel (6)
- Beitrag zu einem Sammelband (2)
- Sonstiges (1)
Sprache
- Englisch (103)
- Deutsch (38)
- Mehrsprachig (1)
Schlagworte
- Fire (12)
- LNG (7)
- Sloshing (7)
- LH2 (5)
- Vessels (5)
- Pressure vessel (4)
- Road tankers (4)
- Tanker (4)
- Turning maneuvers (4)
- BLEVE (3)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (34)
Ermittlung explosionsfähiger Gemische beim Gefahrguttransport unter normalen Beförderungsbedingungen
(2009)
Degradation of material properties significant for lifetime extension of nuclear power plants
(2010)
The discussion about the right energy sources or alternative energy generation goes around the world, mostly in connection with green-house gas reduction. Therefore, some countries have started to consider extending operation of nuclear power plants. This demands an extensive plant life management as well as the knowledge of the degradation in material properties. The Basis Safety Concept (BSC) in Germany observed this circumstance. Still, lifetime extension is not an issue in Germany due to phase out of nuclear energy. Part of the BSC is the application of non-destructive examination (NDE) methods from the beginning, i.e. from component manufacture, to the end of life. The application of a NDE method to detect and size defects in components in nuclear power plants is presented. Some material properties and their degradation during increase of operation time are also in the focus of this paper.
Daten über Schadensursachen und die tatsächliche Nutzungsdauer der Tanks zum Transport von Gefahrgütern liegen nur in begrenztem Maße vor. Auf der Basis der Daten von Tankbaufirmen, Speditionen und Eisenbahnkesselwagen-Vermietgesellschaften wurde die durchschnittliche Lebensdauer von Tankcontainern, Tankfahrzeugen und Kesselwagen zur Beförderung von Gefahrgütern in der Praxis ermittelt und die Hauptschadensursachen analysiert. Korrosion, Risse an Schweißnähten, Gestaltungs- und Dimensionierungsfehler sowie fertigungs- und betriebsbedingte Fehler zählen zu den Hauptschadensursachen. Viele Tanks werden vor Ablauf ihrer Nutzungsdauer nicht mehr für den Transport von Gefahrgütern eingesetzt, da sie nicht mehr den geänderten gesetzlichen Anforderungen in den Gefahrgutvorschriften entsprechen. Die Voraussagen durch Literaturangaben und Ergebnisse von Korrosionsversuchen in der BAM-Liste – Anforderungen an Tanks zur Beförderung gefährlicher Güter – spiegeln sich in der Nutzungsdauer/Lebensdauer der Tanks wider.
Use of higher-alloyed metallic materials and duplex steels for transport tanks of dangerous goods
(2011)
Compatibility evaluations of selected metallic materials under the influence of dangerous goods are published in the BAM-List - Requirements for Tanks for the Transport of Dangerous Goods” as basis for substance-related prototype approvals for tank Containers designed for the carriage of dangerous goods.
There is a request of the tank manufacturing industry and transportation Companies to incorporate additional materials into the BAM-List, especially corrosion-resistant materials because of the large number of corrosive dangerous goods. One solution to solve corrosion Problems is to line the tank with a polymer, an alternative solution is the application of high-alloyed stainless steels and nickel-based alloys as there are 1.4529 (XINiCrMoCu 25-20-7, alloy 926), 1.4562 (X1NiCrMoCu32-28-7, alloy 31) and 2.4605 (NiCr23Mo16AI, alloy 59).
There is an interest to use cost-efficient steels with high strength values and concomitant adequate corrosion resistance such as duplex steel 1.4362 (X2CrNiN23-4).
This steel grade was originally developed as a substitute for the austenitic grades 1.4404 (X2CrNiMo17-12-2) and 1.4571 (X6CrNiMoTi17-12-2). Due to the lower content of the alloy elements nickel and molybdenum this duplex steel is a cost-efficient alternative to molybdenum containing austenite.
Due to the limited number of corrosion test results with welded test samples of these high-alloyed materials and the duplex steel under the influence of corrosive dangerous goods a comprehensive test Programme was performed with these materials in Cooperation with ThyssenKrupp VDM and Deutsche Edelstahlwerke GmbH. It can be concluded from the test results that the superaustenitic steels 1.4529 and 1.4562 as well as the nickel-based alloy 2.4605 are a really good alternative as tank materials for the transport of dangerous goods in comparison to the lining of the tanks. The nickel-based alloy 2.4605 shows the best resistance and is suitable as material for tanks transporting all tested corrosive substances. One exception is the temperature limit during the transport of hydrochloric acid.
The superaustenit 1.4562 is a resistant material with a wide ränge of application. Exceptions for use are: ammonium bifluoride, brine, 34 % calcium Chloride solution, hydrochloric acid, perchloric acid, 90 % 2-chloropropionic acid, nitrating acid with nitric acid content > 50 % and molten monochloroacetic acid. The alloy is limited suitable for allyl Chloride, aluminum Chloride, copper (II) -Chloride and ferric Chloride. The superaustenit 1.4529 showed the lowest resistance compared to the other two materials. This steel is not resistant in hydrochloric acid, perchloric acid, sodium Chlorite and sodium hypochlorite. The application is limited in the concentration ränge of aqueous Solutions of aluminum Chloride, copper (II) Chloride and ferric Chloride. Due to the reduced alloying content of the duplex steel 1.4362 (X2CrNiN23-4) compared to the austenitic CrNiMo-steels, a lower resistance especially in acidic media like formic, acetic or sulfuric acid was observed. Within the more than 7.000 substances contained in the BAM-List there is a large amount of dangerous goods such as hydrocarbons, alcohols, aldehydes, ketones, ethers, esters, and inorganic alkaline substances which have a large transport volume and do not corrode the duplex steel 1.4362 (X2CrNiN23-4).
The test results are included in the actual 11th edition of the BAM-List and therefore available for the costumer.
In-service inspection Atucha
(2011)
Für die Bewertung der Integrität von Tanks ist die detaillierte Kenntnis der belastungsrelevanten Parameter unabdingbar. Die Wärmeübergangszahl a ist eine derartige Größe. Die Wärmeübergangszahl bestimmt direkt die Größe der vorhandenen Beanspruchungen im Tank. Insofern sollte die Wärmeübergangszahl bekannt sein. Aus diesem Grund wurden experimentelle Untersuchungen durchgeführt. Für einen sich im Feuer befindlichen Tank ergibt sich die Wärmeübergangszahl zu 50 W/m2K. Auf dieser Basis konnten die bereits durchgeführten experimentellen Untersuchungen mithilfe der Methode der finiten Elemente nachgerechnet werden. Die dabei erzielten Ergebnisse sind infolge der getroffenen modelltechnischen sowie thermodynamischen Vereinfachungen als zufriedenstellend zu bezeichnen. In einem nächsten Schritt wird an einer verbesserten Modellierung sowie thermodynamischen Beschreibung der Verhältnisse im Tank gearbeitet.
In einem von der BAM Bundesanstalt für Materialforschung und -prüfung durchgeführten Forschungsvorhaben wurde untersucht, inwieweit bei Gefahrguttanks im Brandfall ein 'BLEVE', d. h. ein Versagen der Umschließung mit anschließender Freisetzung der Flüssigkeit bzw. des verflüssigten Gases, verzögert bzw. verhindert werden kann.
Steam generator (SG) tubes are part of the primary circuit of pressurised water reactors and therefore also part of the pressure retaining boundary components. Furthermore, steam generator tubes are the components which guarantee the separation between the primary and secondary circuits. Therefore the knowledge of the loss of tube integrity as soon as possible is an essential. Optimised nondestructive testing methods based on the eddy current array technique are used to find material degradation, especially intergranular stress corrosion cracks during the periodical in-service inspection. These methods are supported by the measurement of the leakage rate during operation based on radioactivity and Tritium measurement regarding a high crack grows. Shutdown criteria depending on leakage rates which are described in the operation procedures but there are no specifications about the conditions for the measured leakage. Is the leakage coming from a single crack or are there multiple cracks or is this the leakage of a critical crack. With the help of FE calculations answer about the uncertainties of leakage rate versus critical crack grows were found. Shutdown criteria must guarantee to avoid critical crack sizes, i.e. between the measured tritium activity and the critical crack size must be a safety gap.
In der Vergangenheit führte die Bundesanstalt für Materialforschung und -prüfung (BAM) zahlreiche Tankbrandversuche mit und ohne Sicherheitseinrichtungen durch. Dabei stellte sich heraus, dass Gastanks mit nicht ausreichend dimensionierten Sicherheitseinrichtungen bei einer äußeren thermischen Belastung innerhalb von 6 bis 10 min in Form eines BLEVE (Boiling Liquid Expanding Vapour Explosion) versagen können. Um die Feuerwiderstandsdauer eines Tanks zu erhöhen, besteht die Möglichkeit, den Tank u. a. mit einer sog. reaktiven Brandschutzbeschichtung zu versehen. Bei einer Temperatureinwirkung ab ca. 200 °C (produktabhängig) beginnt die Schicht aufgrund einer thermochemischen Reaktion aufzuschäumen. Die Tankwand wird dabei temporär vor einer weiteren schnellen Erwärmung geschützt.
Gashochdruckleitungen
(2012)
More than 400 Mt of dangerous materials are transported in Germany every year, of which 150 Mt are by road. Tank containers, tank vehicles and rail tank cars are used for the carriage of dangerous goods in large quantities. Data on the operating life of tanks are only available, in practice, to a minor degree. They are only partly published, mainly after accidents.
The BAM-List - Requirements for Tanks for the Carriage of Dangerous Goods, which has compatibility evaluations of metallic and polymeric materials, has been the basis for substance-related prototype approvals for tank containers and portable tanks designed for the carriage of dangerous goods by the BAM since publication of the first edition in 1989. These data are also used for the approval of rail tank cars and road tank cars and are used as a source of knowledge not only in Germany but also worldwide.
Tank leakages caused by tanks or rail tank cars being made of tank and sealing materials which are not resistant to the fill goods are avoided by using the material resistance data of the BAM.
Corrosion damage is among the main causes of damage. Uniform and non-uniform area corrosion without mechanical stress in aqueous substances is one of the most frequent types of corrosion during the transport of chemicals in tanks. Much damage by pitting corrosion occurs during the transport of substances containing chlorides or substances which separate chloride ions in the presence of moisture.
Operational stresses are caused by the effects of both the road and the dangerous goods being transported. Mechanical damage often results from long-term overstressing and occurs after longer operating times.
Operational failures cause damage which may appear during the service of tank containers, road tank cars or rail tank cars. The damage results from the inattention of employees when opening and closing the valves. Traffic accidents also cause damage to tanks and frames.
Many cases of damage are due to weld area cracks resulting from four basic errors in construction, material, manufacturing and operation. Manufacturing errors can be undetected and the starting point of cracks which only grow under service conditions.
Manufacturing errors result from variations in measurement and design, fittings, state of surface (hardness, abrasiveness) and mechanical surface damage (scratches, cracks). Incorrectly welded joints and errors during mechanical deformation are typical mistakes when installing the component parts. Variations in the wall thickness or combinations of different materials lead to manufacturing errors too. A lot of tanks are not used for the transport of dangerous goods before the end of their service life as they do not fulfil the revised technical safety requirements in the Dangerous Goods Regulations.
Predictions in the BAM-List based on literature data and corrosion test results are reflected in the service (operating) life. Rail tank cars made of carbon steel, for example, which are mainly used for the transport of petroleum products, can achieve a service life of 40 – 50 y.
Rail tank cars produced of austenitic CrNi- or CrNiMo-steel can reach an operating life of at least 30 y, whereby the corrosiveness of the transport substances plays an important role.
Forschen für die Sicherheit
(2013)
Vergleich von Risiken
(2013)
Vielen Entscheidungsprozessen geht ein Vergleich voraus. Bei einem Produktvergleich werden dazu Kriterien festgelegt, etwa der Kaufpreis, die Güte, Haltbarkeit, Handhabung usw. Der Testsieger ist meist derjenige, der die am höchsten bewerteten Kriterien erfüllt. Voraussetzung für derartige Vergleiche ist also die Gleichartigkeit der Vergleichsobjekte. Risiken untereinander zu vergleichen ist komplizierter. Die Notwendigkeit von Risikovergleichen ergibt sich, wenn nur unklare Vorstellungen, z. B. über die Risiken einer neuen Transporttechnologie, existieren und keine Erfahrungswerte zur Verfügung stehen. Aus bekannten und akzeptierten Risiken soll mittels eines Vergleichs die Tolerierbarkeit eines (noch) unbekannten Risikos abgeleitet werden. Der Beitrag setzt sich mit der Problematik von Risikovergleichen auseinander.
Rückendeckung
(2013)
Im Gefahrgutrecht, insbesondere im Bereich der Gefahrguttanks für den Landverkehr, hat der Bezug zur technischen Norm aufgrund der Rechtsfortentwicklung eine fundamentale Bedeutung erlangt. Damit die Interessen der deutschen Tankhersteller genügend Berücksichtigung finden können, ist die kontinuierliche Mitarbeit der betroffenen Wirtschaftskreise in den nationalen und internationalen Normungsgremien erforderlich. Dieser Zusammenhang, der für den einzelnen Hersteller mit erhöhtem Aufwand verbunden ist, wird von den betroffenen Kreisen nicht flächendeckend wahrgenommen. Der Beitrag analysiert Gründe hierfür und macht Vorschläge zu leichten Korrekturen in der inhaltlichen Ausrichtung der Normung.
In Europe, tanks designed on different safety philosophies are used for transporting one and the same liquid dangerous goods (Krautwurst, 2011). Owing to this circumstance, the BAM was commissioned by the BMVBS to conduct a research project designed to analyse and assess the equipment of tanks. Furthermore in these project were researched some failure mechanism of pressure relief devices (PRD).
Based on the knowledge gained, possible solutions were worked out under safety-relevant aspects that would benefit tank transport by providing a lower hazard potential. Besides looking at the mode of operation and the construction of PRV, their blow-off characteristics and total flow rate are considered from a safety engineering point of view.
Based on in-depth studies, a concept for and the further approach to examinations of the failure limits of PRD, especially of spring loaded relief valves, was developed and comprehensively described in the report “The use of safety devices, particularly safety valves, on transport containers” (Pötzsch, Reich, & Jochems, 2011).
The purpose of this study was to investigate failure causes of safety valves by normal modes and accidental fire heat loads. A series of investigations for different influences using safety valves for tanks were obtained. Testing vibration modes and corrosion presents some design limits. Experimental study of a pressure vessel engulfing in fire identify significant design limits. The complete set of results provides direct information of fail-safe modes and discusses the usage.
Neben herkömmlichen Stahlflaschen, die seit Jahrzehnten in fast unveränderter Bauform für Flüssiggase (Propan-Butan-Gemische) eingesetzt werden, etablieren sich immer mehr Flaschen aus Faserverbundwerkstoffen (GFK) mit einer geringeren Masse. Die Bundesanstalt für Materialforschung und -prüfung (BAM) wurde beauftragt, das Verhalten dieser Gasflaschen unter den extremen Bedingungen eines Unfallfeuers zu untersuchen. In einem Brandprüfstand der BAM auf dem Testgelände Technische Sicherheit (TTS) in Horstwalde wurden deshalb beide Typen von Propangasflaschen einem simulierten Unfallfeuer ausgesetzt.
How can the risk of a BLEVE be reduced? That is the main question based on different research projects. In various large scale fire tests fire protection coating systems were used of different manufacturers. The degree of the coating as well as the layer thickness and the processing were varied. These experimental configurations were partly tested with and without pressure relief valve. The pressure relief valves were not protected again the thermal Load from the test fire. The ambition is to find a minimum of the thickness from the fire protection coating witch delay a BLEVE up to 90 minutes. Here are given the most interested configurations of tanks in fire and a description of the test-rigs.
Dangerous goods are transported as air freight in commercial aircrafts. Using plastic jerrycans or plastic containers, liquids or gases can escape by leakage or permeation effects. Prior research by the German Federal Institute for Materials Research and Testing (BAM) showed that the lower explosion limit can be reached when transporting dangerous goods in sea-freight containers under normal transportation situations. This motivated the presented study of the transportation situation of dangerous goods in cargo compartments of commercial airplanes. The scope of this paper is to present the experimental method used for validating a numerical model for CFD (Computational Fluid Dynamics) simulations. The CFD model will be used in a future study to evaluate the potential risk from transporting dangerous goods.
The objective of this paper is to present the model mock-up of an aircraft cargo compartment and some examples of three dimensional velocity profiles of the air flow in the mock-up. The velocity profiles are calculated using numerical simulations and measured by Laser-Doppler-Anemometry (LDA) experiments. The mock-up is a generic model of a wide-body aircraft lower deck cargo compartment in a 1:10 scale. Geometry, air exchange rates and inlet as well as outlet flow conditions in the cargo compartment are modeled using realistic boundary conditions. The commercial CFD (Computational Fluid Dynamics) code ANSYS CFX 14 is used for numerical flow simulations applying RANS (Reynolds-Averaged-Navier-Stokes) equations and turbulence models. The turbulence models studied are the renormalization group k-ε-model (RNG), the Reynolds-Stress model by Launder, Reece and Rodi (LRR) and the SST-k-ω-model by Menter (SST).
The flow measurement with LDA in the mock-up of a cargo compartment proves to be a feasible method for producing data to validate CFD simulations. Qualitative evaluation of the results shows a good overall agreement between numerical and experimental results. The experimental validation indicates that the implemented CFD model is capable of reproducing the flow situation in the model mock-up.
Die Vorhersage der Beanspruchung bei plastischem Versagen von zylindrischen Druckbehältern wird häufig mittels Finite Elemente Berechnungen durchgeführt. Die Berechnung der zulässigen Beanspruchung erfordert ein elastisch-plastisches Werkstoffmodell und die Berücksichtigung von nichtlinearen geometrischen Effekten. Das plastische Versagen verursacht eine gesamte Strukturinstabilität und kann nicht direkt aus der Finite Elemente Analyse bestimmt werden. In dem vorliegenden Beitrag wird die Beanspruchung für plastisches Versagen eines zylindrischen Druckbehälters mittels eines analytischen Verfahrens basierend auf einem linear elastischen ideal-plastischen Materialmodell bestimmt. Wenn Plastizität auftritt, wird zum einen der Werkstoff als inkompressibel und zum anderen der Tensor der plastischen Dehnungen als parallel zum Spannungsabweichungstensor angenommen. In diesem Fall kann die Spannungs-Dehnungs-Beziehung von Henkel angewendet werden, um den Druck zu berechnen, bei dem plastisches Fließen und Versagen eintritt. Die analytischen Ergebnisse werden von den Finite Elemente Berechnungen vollkommen bestätigt.
Nondestructive Testing (NDT) and fracture mechanics are two different disciplines in applied engineering science. Both areas are very important for the evaluation of the component integrity. Unfortunately the technical understanding in both disciplines is not identically, what lead to misunderstandings. In the present paper, the basic ideas about fracture mechanics and the input parameters coming from the NDT side are explained, concerning the integrity evaluation of the components. The widely used NDT methods are magnetic particle, dye penetrant, electrical eddy currents, radiography and ultrasonics. But not all of these common NDT methods can deliver parameters satisfy the fracture mechanics requirements. The first two can detect only surface-breaking or immediately sub-surface defects. Eddy current can also find defects in deeper sub-surface layers, while radiography and ultrasonics can also find embedded, remote defects. These three methods have furthermore a high potential for defect sizing and are therefore predestined to provide fracture mechanics input parameters. At the example of steam generator tube inspection the interplay of eddy current and fracture mechanics as related to tube integrity will be explained.
Pressure Vessel Fire Test
(2014)
Limit load analysis is a well known method to calculate the allowable design pressure of container components. A limit load of a pressurized container is achieved, when the stress of a wall and the flow stress are equal. In the following paper the transferability of limit load analysis from small scale tank containers up to large scale containers (railway tank) are investigated. Finite element calculations are carried out and compared with experimental results. It can be concluded that the limit load analysis works very well. Furthermore, the yield strength of the material should be used as flow stress.
The prediction of the plastic collapse load of cylindrical pressure vessels is very often made by using expensive Finite Element Computations. The calculation of the collapse load requires an elastic-plastic material model and the consideration of non-linear geometry effects. The plastic collapse load causes overalls structural instability and cannot be determined directly from a finite element analysis. The ASME (2007) code recommends that the collapse load should be the load for which the numerical solution does not converge. This load can be only determined approximately if a expensive nonlinear analysis consisting of a very large number of sub steps is done. The last load sub step leading to a convergent solution will be taken as the critical load for the structure. In the instability regime no standard finite element solution can be found because of the lack of convergence of the numerical procedure. Other methods for the calculation of the allowable pressure proposed by the ASME code are the elastic stress analysis and the limit load analysis. In the present paper the plastic collapse load for a cylindrical pressure vessel is determined by an analytical method based on a linear elastic perfectly plastic material model. When plasticity occurs the material is considered as incompressible and the tensor of plastic strains is parallel to the stress deviator tensor. In that case the finite stress-strain relationships of Henkel can be used for calculating the pressure for which plastic flow occurs at the inside of the vessel wall or in the case of full plasticity in the wall. The analytical results are fully confirmed by finite element predictions both for axisymmetric and high costs three dimensional models. The analytical model can be used for fast predictions of the allowable load for the design of a large variety of pressure vessels under safety considerations. The accuracy of the predicted collapse load largely depends on the quality of the temperature dependent wall material data used both in the analytical and numerical calculations.
The US Department of Transportation, Federal Railroad Administration (FRA) current regulations for rail tank cars in the United States stipulate that, for certain hazardous materials, tank cars shall have a thermal protection system capable of preventing rupture of the tank for 100 minutes when exposed to an engulfing fire with a blackbody equivalent flame temperature of 871 °C (+/- 56°C), and that tanks shall have a pressure relief device set at an appropriate level (depending on the type of tank car and contents). Pressure relief devices are a source of non-accident releases, and hence may cause serious incidents when tanks are transporting hazardous materials. Industry in North America would therefore benefit from removal of pressure relief devices on tanks transporting certain hazardous materials. Such an approach is known as full Containment, and is standard practice in Europe. In 2014 the FRA commissioned an experimental study to investigate the ability of a specific design of rail tank to resist rupture without incorporating a pressure release valve. As a precursor to tests on tanks there was a need to develop and characterise a simulated pool fire capable of reliably exposing large-scale tanks to repeatable, uniform conditions. This paper describes such a fire test setup, developed using a burner array system fuelled by liquid propane and designed to produce luminous, low velocity flames representative of those found in large hydrocarbon pool fires. The experimental set-up is described, along with the Instrumentation (directional flame thermometers, infra-red camera, and thermally massive calorimeter) and methodology used to characterise the fire. Comparisons are made against previous fire tests on vessels to assess the suitability of the experimental set-up for future vessel testing.
Given the frequent incidences of Non-Accident Releases (NARs) of hazardous materials from tank cars, there in an increasing interest in transporting hazardous materials in total containment conditions (i.e., no pressure relief devices). However, the ability of tank cars to meet thermal protection requirements provided in the Code of Federal Regulations under conditions of total containment has not been established. Also, the modeling tool commonly used by industry to evaluate thermal protection, AFFTAC, has not been validated under these conditions. The intent of this effort was to evaluate through a series of third-scale fire tests, the ability of tank cars to meet the thermal protection requirements under total containment conditions, and also, to validate AFFTAC for such conditions.
This paper describes the test design and planning effort associated with this research, including the design and evaluation of a fire test setup to simulate a credible, fully engulfing, pool fire that is consistent and repeatable, and the design and hydro-static testing of a third-scale tank specimen. The fire design includes controls on the spatial distribution and temperature variation of the flame temperature, the heat flux, and the radiative balance, to best reflect large liquid hydrocarbon pool fire conditions that may be experienced during derailment scenarios.
Using plastic jerrycans or plastic containers, dangerous goods are transported as air freight in commercial aircrafts. Liquids or gases can escape by leakage or permeation effects from these plastic containers. The German Federal Institute for Materials Research and Testing (BAM) conducted prior research which showed that the lower explosion limit can be reached when transporting dangerous goods in sea-freight containers under normal transportation situations. The presented study is motivated based on these findings. The research objective of this study is to analyze the transportation situation of dangerous goods in cargo compartments of commercial airplanes. The scope of this paper is to present the experimental method used for validating a numerical model for CFD (Computational Fluid Dynamics) simulations and to present some simulation results of the mass transport of dangerous goods in the cargo compartment.
The velocity profiles and the mass transport is calculated using numerical simulations and measured by Laser-Doppler-Anemometry (LDA) experiments. The mock-up is a generic model of a wide-body aircraft lower deck cargo compartment in a 1: 10 scale. Geometry, air exchange rates and inlet as well as outlet flow conditions in the cargo compartment are modeled using realistic boundary conditions. The commercial CFD (Computational Fluid Dynamics) code ANSYS CFX 14 is used for numerical flow simulations applying RANS (Reynolds-Averaged-Navier-Stokes) equations and turbulence models. The turbulence models studied are the renormalization group k-e-model (RNG), the BSL-Reynolds-Stress model (BSL) and the SST-k-co-model by Menter (SST).
The flow measurement with LDA in the mock-up of a cargo compartment proves to be a feasible method for producing data to validate CFD simulations. Qualitative evaluation of the results shows a good overall agreement between numerical and experimental results. The experimental validation indicates that the implemented CFD model is capable of reproducing the flow situation in the model mock-up